F373512 Force PLATE, INSERT


F373512 PLATE, INSERT Force H0757H75A, H0757H76C, H0859H77A, H0859H78A, H1059H76D, H1059H77G, H1159H77A, H1159H78B, H1209H76F, H1409H78A PLATE
F373512 PLATE, INSERT Force
Rating:
98

Buy PLATE, INSERT F373512 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

Force entire parts catalog list:

H0757H75A 1975,1976
H0757H76C 1976
H0859H77A 1977
H0859H78A 1978
H1059H76D 1976
H1059H77G 1977
H1159H77A 1977
H1159H78B 1978
H1209H76F 1976,1977
H1409H78A 1978

Information:


Table 1
Diagnostic Trouble Codes
J1939 Code and Description CDL Code and Description Comments
3216-7
Aftertreatment #1 Intake NOx : Not Responding Properly E1431 (2)
Aftertreatment #1 Intake NOx : Not Responding Properly The aftertreatment intake NOx level is not responding as expected.
The code is logged.
3226-7
Aftertreatment #1 Outlet NOx : Not Responding Properly E1432 (2)
Aftertreatment #1 Outlet NOx : Not Responding Properly The aftertreatment outlet NOx level is not responding as expected.
The code is logged.
Table 2
Required Tools
Qty Part Number Part Description
1 441-0451 Tool Gp Reference: Refer to the Disassembly and Assembly for the appropriate procedure for the removal and installation of components.
Table 3
Troubleshooting Test Steps Values Results
1. Check the Diesel Exhaust Fluid (DEF) Quality.
A. Measure the DEF quality. Refer to Testing and Adjusting, "Diesel Exhaust Fluid Quality - Test" for the correct procedure.
DEF Quality
Result : The DEF is not contaminated and the concentration is not within the acceptable range.
Repair : Drain the DEF from the tank. Refill the tank with DEF that meets ISO 22241 quality standards.
Proceed to Test Step 3.
Result : The DEF is not contaminated and the concentration is within the acceptable range.
Proceed to Test Step 2.
Result : The DEF is contaminated.
Repair : Contact the Dealer Solution Network (DSN) for further information.
2. Perform the "DEF Dosing System Accuracy Test" Using Cat® Electronic Technician (ET)
A. Refer to Testing and Adjusting, Aftertreatment SCR System Dosing Test, for the correct procedure.
DEF Dosing System Accuracy Test
Result : The quantity collected is within specifications.
Repair : Install the DEF injector.
Proceed to Test Step 4.
Result : The quantity collected is below specification.
Proceed to Test Step 3.
Result : The quantity collected is above specification. A failed DEF injector has been detected.
Repair : Replace the failed DEF injector.
Proceed to Test Step 4.
3. Check the DEF Pressure Line.
A. Turn the keyswitch to OFF. Allow 2 minutes to elapse before proceeding.
B. Visually inspect the lines for leaks or damage.
C. Remove the DEF pressure line between the DEF pump and the DEF injector.
D. Inspect the DEF pressure line for obstructions. Flush the line with water or low-pressure air, if necessary.
Note: Possible obstructions are ice, DEF deposits, or debris.
Restrictions, Obstructions, or Leaks
Result : An obstruction was found.
Repair : Flush or replace the line. Install the DEF injector.
Proceed to Test Step 4.
Result : An obstruction was not found.
Repair : Proceed to Troubleshooting, "DEF Pressure is Low".
4. Perform an "Aftertreatment System Functional Test"
A. Establish communication between Cat ET and the engine Electronic Control Module (ECM).
B. Perform a "Aftertreatment System Functional Test" using Cat ET.
Successful Test
Result : The test completed successfully.
Return the unit to service.
Result : The test did not complete successfully.
Proceed to Test Step 5.
5. Check for an Engine Misfire
A. Establish communication between Cat ET and the engine ECM.
B. Perform a "Cylinder Cutout Test".
Misfire
Result : A misfire was detected.
Repair : Replace or repair the failed component or components.
Proceed to Test Step 7.
Result : A misfire was not detected.
Proceed to Test Step 6.
6. Check the Exhaust System for Leaks
A. Check the entire exhaust system for leaks.
Exhaust Leaks
Result: There were not any exhaust leaks found.
Repair : For a 3216-7 or E1431 (2) code replace the intake NOx sensor.
Repair : For a 3226-7 or E1432 (2) code replace the outlet NOx sensor.
Proceed to Test Step 7.
Result : There were exhaust leaks found.
Repair : Repair the exhaust leaks.
Proceed to Test Step 7.
7. Perform the "Aftertreatment System Functional Test" in Cat ET
A. Establish communication between Cat ET and the engine ECM.
B. Perform the "Aftertreatment System Functional Test".
Successful Test
Result: The test completed successfully.
Return the unit to service.


Parts plate Force:

F480386
 
F480386 PLATE, REAR
H0757H75A, H0757H76C
F333392
 
F333392 PLATE, SIDE
H0757H75A, H0757H76C, H0859H77A, H0859H78A, H1059H76D, H1059H77G, H1159H77A, H1159H78B, H1209H76F, H1409H78A
F480711
 
F480711 PLATE, ENGINE COVER FRONT
H0757H75A, H0757H76C, H0859H77A, H0859H78A
F489386
 
F489386 PLATE REAR
H1059H76D, H1059H77G, H1209H76F
F489711
 
F489711 PLATE, ENGINE COVER FRONT
H1059H76D, H1059H77G, H1159H77A, H1159H78B, H1209H76F, H1409H78A
F370386
 
F370386 PLATE, REAR
H0859H77A, H0859H78A
FA449799
 
FA449799 PLATE ASSEMBLY
H0859H77A, H1159H77A
F333386
 
F333386 PLATE, REAR
H1159H77A, H1159H78B, H1409H78A
Back to top