F516885 Force PLUG, SPRING HOLDING


F516885 PLUG, SPRING HOLDING Force H0060B76A, H0060H79C, H0060H80D, H0064H80F, H0070B79A, H0075H79A, H0091B80B, H0091H79A, H0095B80F, H0101B78A, H0121B79A, H0125H79E PLUG
F516885 PLUG, SPRING HOLDING Force
Rating:
48

Buy PLUG, SPRING HOLDING F516885 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 21
 

Force entire parts catalog list:

H0060B76A 1976
H0060H79C 1979
H0060H80D 1980
H0064H80F 1980
H0070B79A 1979
H0075H79A 1979
H0091B80B 1980
H0091H79A 1979
H0095B80F 1980
H0101B78A 1978
H0121B79A 1979
H0125H79E 1979

Information:


Illustration 1 g01233970
Schematic for the Cat Data Link
Test Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Illustration 2 g01167488
Typical engine view
(1) J1/P1 ECM connectors
Illustration 3 g01149983
Typical engine view
(2) P61 customer connector
(3) P63 service tool connector
Thoroughly inspect connectors (1), (2), and (3). Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Illustration 4 g01202018
P1 terminals that are associated with the Cat Data Link
(P1-8) Cat Data Link +
(P1-9) Cat Data Link −
Illustration 5 g01119122
J61 and P61 terminals that are associated with the Cat Data Link
(6) Cat Data Link −
(7) Cat Data Link +
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the Cat Data Link.
Check the allen head screw on each ECM connector for the proper torque. Also, check the allen head screw on the customer connector for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values. Expected Result:All connectors, pins, and sockets are completely inserted and coupled. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and the connectors appear to be OK. Proceed to Test Step 2.
Not OK - The connectors and/or the wiring are not OK.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the original problem is resolved.STOPTest Step 2. Check for a Short Circuit
Disconnect the J1 connector.
Disconnect Cat ET from the service tool connector.
Measure the resistance between the points that are listed in Table 1. Be sure to wiggle the wires in the harnesses as you make each resistance measurement.
Table 1
Resistance Measurements for the Cat Data Link
Connector and Terminal Terminal
P1-8 (Cat Data Link +) All of the other terminals on the P1 connector
Ground stud
P1-9 (Cat Data Link -) All of the other terminals on the P1 connector
Ground stud Expected Result:Each check of the resistance indicates an open circuit.Results:
OK - Each check of the resistance indicates an open circuit. Proceed to Test Step 3.
Not OK - At least one check of the resistance does not indicate an open circuit. There is a short circuit in the harness or in a connector.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Verify that the original problem is resolved.STOPTest Step 3. Check for an Open Circuit
Fabricate a jumper wire. Use the jumper wire in order to create a short circuit between terminals J63-D (Cat Data Link +) and J63-E (Cat Data Link −).
Measure the resistance between P1-8 (Cat Data Link +) and P1-9 (Cat Data Link −). Expected Result:Each check of the resistance is less than ten Ohms.Results:
OK - Each check of the resistance is less than ten Ohms.Repair: Perform the following procedure:
Connect the J1/P1 connectors. Connect Cat ET to the service tool connector.
Check the Cat Data Link for proper operation. If the Data Link does not operate correctly, there may be a problem with the ECM. Temporarily install a new ECM. Check the Cat Data Link again. If the new ECM solves the problem, install the original ECM and verify that the original problem returns. If the new ECM operates correctly and the original ECM does not operate correctly, replace the original ECM. Verify that the problem is resolved.STOP
Not OK - At least one check of the resistance is greater than ten Ohms. There is an open circuit or excessive resistance in the harness. There may be a problem with a connector.Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Verify that the original problem is resolved.STOP


Parts plug Force:

F50109
 
F50109 PLUG, GEAR HOUSING
H0032H84G, H0033H75C, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H78D, H0042H79F, H0043F85A, H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0054H76D, H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78
F388226-1
 
F388226-1 PLUG
H0060B76A, H0062H79M, H0082H79K
F387226-1
 
F387226-1 PLUG
H0060B76A, H0082H76G
F343226-1
 
F343226-1 PLUG
H0060B76A, H0062H79M, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0094H81F, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0152B78D, H0152B83J, H0152C84
FC503227
 
FC503227 PLUG, SPARK CHAMPION (QL-77J4) FOR MODELS 108B9B, 109B8B
H0091B80B, H0091H79A, H0091H83C, H0092H79F, H0095B81G, H0095H82H, H0102H78E, H0121B79A, H0122H79E, H0125H79E, H0152B78D, H0152B83J, H0152C84K, H0152H79E, H0202B81M, H0202H79K, H0252B83G, H0306B80C, H0307H81D, H0357C86A, H0357C87A, H0357C88B, H0357F88
F174227
Back to top