F650450 Force RECTIFIER


F650450 RECTIFIER Force H0257F88A, H0257F88B, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0357C86A, H0357C87A, H0357C88B, H0357F88A, H0357F89C, H0357G90A, H0507C86A, H0507C87A, H0507C87C, H0507C88B, H0507F87B, H0507F88A, H0851X88A, H0853F88B, H0853F89 RECTIFIER
F650450 RECTIFIER Force
Rating:
83

Buy RECTIFIER F650450 Force genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$59.95
 

10-08-2024

US: Pwc Engine, Inc.
Chrysler Force Universal Rectifier 20 Amp 25 Hp 1975-1982 Model# Electric Start WSM 152-9209 OEM# F684450, F650450, F404470, F404470-1, F475450
Pwc Engine High Performace Quality OEM Style Rectifiers / Regulators. || Rectifier / Regulator meets OEM standards or higher. || PWC Engine brings Higher Quality for an awesome price!
$59.95
 

09-06-2024

US: Pwc Engine, Inc.
Universal Rectifier is Compatible with Chrysler Force 20 Amp 35 Hp 1983-1984 Model# W/CD-Alternator 152-9209 OEM# F684450, F650450, F404470, F404470-1, F475450
Pwc Engine High Performace Quality OEM Style Rectifiers / Regulators. || Rectifier / Regulator meets OEM standards or higher. || PWC Engine brings Higher Quality for an awesome price!
$59.95
 

06-05-2024

US: Pwc Engine, Inc.
Chrysler Force Universal Rectifier 20 Amp 35 Hp 1978 Model# W/CD-Alternator WSM 152-9209 OEM# F474470, F404470-0, F510450, F510450-1, FA617450, F650450
Pwc Engine High Performace Quality OEM Style Rectifiers / Regulators. || Rectifier / Regulator meets OEM standards or higher. || PWC Engine brings Higher Quality for an awesome price!
Number on catalog scheme: 23
 

Force entire parts catalog list:

H0257F88A 1988,1989
H0257F88B 1988,1989,1991
H0352F90B 1990
H0352F90C 1990
H0353E91A 1991
H0353E91B 1991
H0355D89A 1989
H0356F89B 1989
H0357C86A 1986
H0357C87A 1987
H0357C88B 1988
H0357F88A 1988
H0357F89C 1989
H0357G90A 1990
H0507C86A 1986
H0507C87A 1987
H0507C87C 1987
H0507C88B 1988
H0507F87B 1987
H0507F88A 1988
H0851X88A 1988
H0853F88B 1988,1989
H0853F89C 1989
H0856A89A 1989
H0856C87A 1987
H0856C87B 1987
H0856F86A 1986
H0856Y89B 1989
H1251A88A 1988
H1251A88B 1988
H1251A88C 1988
H1251A89B 1989
H1251A89C 1989
H1251F86A 1986
H1251F87A 1987
H1251F87B 1987

Information:

1. Remove bolts (1) from the alternator bracket.2. Remove the bolts that hold plate (3), and remove the plate.3. Disconnect water line (2) from the air compressor. Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt. 4. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.5. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb.).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
6. Remove the gasket and seals from the spacer plate.Install Cylinder Head Assembly
Be sure a new gasket has been installed between the spacer plate and the cylinder block. See Remove And Install Spacer Plate. 1. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (1) and two O-ring seals (2). 2. Fasten a hoist, and put cylinder head assembly (3) in position on the cylinder block.3. Put 5P3931 Anti-Seize Compound on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown in illustration A87019X1 on page 6-119.a. Tighten bolts 1 through 20 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).b. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).c. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.d. Install the rocker shaft assemblies and push rods. See Install Rocker Shaft Assemblies And Push Rods.e. Tighten bolts 21 through 26 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).f. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).g. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.h. Tighten the 3/8" bolts to a torque of 43 7 N m (32 5 lb.ft.). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 25 4 N m (18 3 lb.ft.).4. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in.) for intake and 0.76 mm (.030 in.) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb.ft.).5. Install the valve cover bases and the inner fuel lines. See Install Rocker Shaft Assemblies And Push Rods.6. Install the valve covers. See Install Valve Covers. 7. Install plate (4).8. Connect the water line to the air compressor.9. Install bolts (5) for the alternator bracket.END BY:a. install exhaust manifoldb. install fuel injection linesc. install aftercooler housingd. install water temperature regulator


Back to top