FK10353 REPAIR KIT Force
H0091H84D, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015211SS, H0152C84K, H0152S89A
REPAIR
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Compatible models:
Force entire parts catalog list:
H009201SD 1996,1997
H0092284D 1984,1985,1986,1987,1988,1989,1990,1991,1992,1993,1994,1995
H0092H84L 1984
H0092S88A 1988
H0092S91A 1991
H0093S91A 1991
H015201RS 1995
- CARBURETOR » FK10353
- CARBURETOR (15 HP MODEL) (1300-F715061-1) » FK10353
- CARBURETOR » FK10353
H0152S89A 1989
Information:
start by: a) remove valve cover The following steps can be used for the direct injection and precombustion engines except the direct injection engines do not have glow plugs and wires. 1. Remove clip (2) for glow plug wire and fuel injection line (1). Use tool (A) to remove the fuel injection line from the fuel injection valve. 2. Remove fuel line adapters (4) and the spacers from valve cover base (3). Remove the O-ring seal from the adapter.3. Remove bolts (5) and washers (6) that hold rocker shaft assembly (7).4. Remove the rocker shaft assembly. All push rods except those at each end can be removed without removal of the rocker shaft.5. Remove the push rods from the cylinder head.6. Remove intake bridge (9) and exhaust bridge (8) from the bridge dowels. Put identification on the parts to prevent a mix at installation.Install Rocker Shaft Assembly And Push Rods
1. Put clean SAE 30 oil on the bridge dowel and install exhaust bridge (3) and intake bridge (2) in their correct locations.2. Put finger pressure on top of the bridge and turn the adjusting screw clockwise until it makes contact with the valve stem. Turn the adjusting screw 20° to 30° more. Hold the adjusting screw in this position and tighten the locknut to a torque of 22 3 lb.ft. (28 4 N m).3. Put clean SAE 30 oil on top of the pad on the bridge.4. Install push rods (1) and the rocker shaft assembly. Put clean SAE 30 oil on the threads of the bolts that hold the rocker shaft in position. Install the bolts and washers. 5. Tighten the bolts that hold rocker shaft assembly (8) as follows: a) Tighten the bolts in number sequence to a torque of 200 20 lb.ft. (270 25 N m).b) Tighten the bolts again in number sequence to a torque of 330 15 lb.ft. (447 20 N m).c) Tighten the bolts again in number sequence to a torque of 330 15 lb.ft. (447 20 N m).6. Make an adjustment of the correct valve clearances. The clearance must be .015 in. (0.38 mm) for intake and .030 in. (0.76 mm) for exhaust. See VALVE CLEARANCE SETTING in TESTING AND ADJUSTING. 7. Put clean SAE 30 oil on the O-ring seal and install O-ring seal (9) on adapter (10). Install the adapter in valve cover base (11). Install the locks, spacers and nuts that hold it.8. Install the fuel injection line on the adapter and the fuel injection valve. Tighten the nut on the fuel injection valve with tool (A) to a torque of 55 5 lb.ft. (75 7 N m). Tighten the nut on the adapter with tool (A) to a torque of 30 5 lb.ft. (40 7 N m).9. Connect the wire to the glow plug. Connect the clip for the glow plug to the fuel injection line with the wire on the same side as the glow plug.end by: a) install valve cover
1. Put clean SAE 30 oil on the bridge dowel and install exhaust bridge (3) and intake bridge (2) in their correct locations.2. Put finger pressure on top of the bridge and turn the adjusting screw clockwise until it makes contact with the valve stem. Turn the adjusting screw 20° to 30° more. Hold the adjusting screw in this position and tighten the locknut to a torque of 22 3 lb.ft. (28 4 N m).3. Put clean SAE 30 oil on top of the pad on the bridge.4. Install push rods (1) and the rocker shaft assembly. Put clean SAE 30 oil on the threads of the bolts that hold the rocker shaft in position. Install the bolts and washers. 5. Tighten the bolts that hold rocker shaft assembly (8) as follows: a) Tighten the bolts in number sequence to a torque of 200 20 lb.ft. (270 25 N m).b) Tighten the bolts again in number sequence to a torque of 330 15 lb.ft. (447 20 N m).c) Tighten the bolts again in number sequence to a torque of 330 15 lb.ft. (447 20 N m).6. Make an adjustment of the correct valve clearances. The clearance must be .015 in. (0.38 mm) for intake and .030 in. (0.76 mm) for exhaust. See VALVE CLEARANCE SETTING in TESTING AND ADJUSTING. 7. Put clean SAE 30 oil on the O-ring seal and install O-ring seal (9) on adapter (10). Install the adapter in valve cover base (11). Install the locks, spacers and nuts that hold it.8. Install the fuel injection line on the adapter and the fuel injection valve. Tighten the nut on the fuel injection valve with tool (A) to a torque of 55 5 lb.ft. (75 7 N m). Tighten the nut on the adapter with tool (A) to a torque of 30 5 lb.ft. (40 7 N m).9. Connect the wire to the glow plug. Connect the clip for the glow plug to the fuel injection line with the wire on the same side as the glow plug.end by: a) install valve cover
Parts repair Force:
FK10114
FK10114 REPAIR KIT
H0091H83C, H0091H84D, H0092284D, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0095H82H, H0152C84K, H0152S89A
FK10123
FK10123 REPAIR PARTS KIT.
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0152B83J, H0152C84K, H0152S89A
FK10295
FK10295 REPAIR KIT-CARBURETOR (9.9/15)
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015211SS, H0152C84K, H0152S89A
FK10244
K10295
854219A 1
854210A 1