FA458480 Force ENGINE COVER RETAINER W/SCREWS & NUT


FA458480 ENGINE COVER RETAINER W/SCREWS & NUT Force H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0357C86A, H0357C87A, H0357F88 ENGINE
FA458480 ENGINE COVER RETAINER W/SCREWS & NUT Force
Rating:
98

Buy ENGINE COVER RETAINER W/SCREWS & NUT FA458480 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Force entire parts catalog list:

H0202B80L 1980
H0202B81M 1981
H0202H79K 1979
H0202H82N 1982
H0252B83G 1983,1984
H0252H77B 1977
H0252H78C 1978
H0252H78D 1978
H0254H75A 1975,1976
H0306B80C 1980
H0307H81D 1981
H0350H78L 1978
H0351H76K 1976
H0352H77H 1977,1978
H0352H79L 1979
H0353H78K 1978
H0353H80M 1980
H0353H81N 1981
H0353H82P 1982
H0356H75F 1975,1976,1977
H0357C86A 1986
H0357C87A 1987
H0357F88A 1988
H0357H83N 1983,1984
H0456B78J 1978
H0456B79K 1979
H0456B80L 1980,1981
H0457H82N 1982
H0457H83P 1983,1984
H0503H84B 1984
H0507B85A 1985
H0507C86A 1986
H0507C87A 1987
H0507C87C 1987
H0507F87B 1987
H0507F88A 1988
H0507H81A 1981
H0507H82B 1982
H0555H74G 1974,1976

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 194-3536 T40 Torx Socket 1
B 227-4389 E10 Torx Socket 1 Note: The crankshaft rear seal and the housing are manufactured as one assembly.Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The crankshaft rear seal must be installed dry.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01986153
Illustration 2 g01986154
Ensure that crankshaft flange (1) is clean, dry, and free from damage.
Ensure that the gasket surface of the cylinder block is clean, dry, and free from damage. Ensure that the gasket surface of isolating frame (6) is clean, dry, and free from damage.
Ensure that plastic sleeve (3) is squarely installed within new crankshaft rear seal (2). Note: The plastic sleeve is included in order to protect the lip of the seal as the crankshaft rear seal is pushed over crankshaft flange (1). Do not attempt to install a crankshaft rear seal without the plastic sleeve.
Place the assembly of crankshaft rear seal (2) over crankshaft flange (1). Align dowel (5) with the slot in crankshaft rear seal (2).
Ensure that plastic sleeve (3) is engaged on crankshaft flange (1). Push crankshaft rear seal (2) squarely onto the crankshaft. Ensure that the crankshaft rear seal is seated against the cylinder block. During this process, plastic sleeve (3) will be forced out of the crankshaft rear seal. Discard the plastic sleeve. Note: Ensure that dowel (5) is engaged in the slot in the crankshaft rear seal.
Use Tooling (A) in order to install two outer Torx bolts (7) at the base of crankshaft rear seal (2). Tighten Torx bolts (7) to a torque of 15 N m (133 lb in).
Use Tooling (B) in order to install two Torx bolts (4) to crankshaft rear seal (2) at Position (X). Tighten Torx bolts (4) to a torque of 22 N m (195 lb in).
Use Tooling (A) in order to unscrew Torx bolts (7) by one complete turn.
Use Tooling (A) in order to install remaining Torx bolts (7). Tighten all Torx bolts (7) to a torque of 22 N m (195 lb in).
Illustration 3 g02469677
Tighten all Torx bolts (4) in the numerical sequence that is shown in Illustration 3. Tighten all Torx bolts (4) to a torque of 22 N m (195 lb in). End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install" for the correct procedure. Installation Procedure Without Isolating Frame for the Oil Pan
Table 2
Required Tools
Tool Part Number Part Description Qty
A 194-3536 T40 Torx Socket 1
C - Alignment Tool 1
- Bolts (M8 by 20 mm) 4 Note: The crankshaft rear seal and the housing are manufactured as one assembly.Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The crankshaft rear seal must be installed dry.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 4 g01279001
Alignment tool
To install the crankshaft rear seal without the isolating frame for the oil pan in position, Tooling (C) must be used. The tool should be fabricated from 8 mm (5/16 inch) steel stock. The dimensions for the tool are given in Illustration 4. All dimensions are shown in millimeters.
Illustration 5 g02435316
Illustration 6 g01988593
Ensure that crankshaft flange (1) is clean, dry, and free from damage.
Ensure that the gasket surface of the cylinder block is clean and dry.
Ensure that plastic sleeve (3) is squarely installed within new crankshaft rear seal (2). Note: The plastic sleeve is included in order to protect the lip of the seal as the crankshaft rear seal is pushed over crankshaft flange (1). Do not attempt to install a crankshaft rear seal without the plastic sleeve.
Place the assembly of the crankshaft rear seal over crankshaft flange (1). Align dowel (5) with the slot in the crankshaft rear seal.
Ensure that plastic sleeve (3) is engaged on crankshaft flange (1)


Parts engine Force:

FS463712
 
FS463712 ENGINE COVER
H0352H77H, H0356H75F, H0555H74G
FA366778
 
FA366778 ENGINE COVER RETAINER, W/SCREWS AND NUTS
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507C87C, H0507F87B, H0507F88A, H0507H81A, H0507H82B, H0555H74G
2C 575712
2C 576712
818015A 1
 
818015A 1 ENGINE COVER
H0202B81M, H0202H82N, H0252B83G, H0307H81D, H0357C86A, H0357H83N
F2C661712
FS662712
 
FS662712 ENGINE COVER
H0507C87A, H0507C87C, H0507F87B, H0507F88A
F2C662712
 
F2C662712 ENGINE COVER COMPLETE
H0507C87A, H0507C87C, H0507F87B
Back to top