F369349 Force REVERSE LOCK


F369349 REVERSE LOCK Force H0709B79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H82E, H0850H81C, H0851X88A, H0853F88B, H0856A89A, H0856B80H, H0856C87A, H0856C87B, H0856F84A, H0856F85A, H0856F86A, H0856H82K, H0857B78F, H0857H79G, H0858C84 REVERSE
F369349 REVERSE LOCK Force
Rating:
53

Buy REVERSE LOCK F369349 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 37
 

Force entire parts catalog list:

H0709B79A 1979
H0756H80F 1980
H0756H81G 1981
H0756H82H 1982
H0757B79E 1979
H0757H75A 1975,1976
H0757H76C 1976
H0757H78D 1978
H0758H82E 1982,1983,1984
H0850H81C 1981
H0851X88A 1988
H0853F88B 1988,1989
H0856A89A 1989
H0856B80H 1980
H0856C87A 1987
H0856C87B 1987
H0856F84A 1984
H0856F85A 1985
H0856F86A 1986
H0856H82K 1982,1983
H0857B78F 1978
H0857H79G 1979
H0858C84H 1984
H0903E91D 1991
H0903E91H 1991,1992,1993,1994
H0903F90B 1990
H0903F90C 1990
H0903F91A 1991
H0903F91C 1991
H0906A90A 1990
H1006B80B 1980
H1006B81C 1981
H1007H79A 1979
H1057B78H 1978
H1058H82G 1982
H1059H76D 1976
H1059H77G 1977
H1156H80C 1980
H1156H81D 1981
H1157B79B 1979
H1157H78A 1978
H1158B82E 1982
H1209H76F 1976,1977
H1406H80C 1980
H1406H81D 1981
H1407B79B 1979
H1407H78A 1978
H1408H82D 1982

Information:


Illustration 1 g00812448
SchematicTest Step 1. Test Communication of the CAT Data Link
Turn the keyswitch to the OFF/RESET position.
Connect the electronic service tool to the service tool connector.
Turn the keyswitch to the ON position.
Select the engine ECM from the "ECM Selector" screen on the electronic service tool.Results:
OK - The CAT Data Link is functioning properly. Proceed to Test Step 2.
Not OK - The CAT Data Link is not functioning properly.Repair: Proceed to Troubleshooting, "Electronic Service Tool Will Not Communicate with ECM". Stop.Test Step 2. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect the J1/P1 ECM connector and all other connectors in the wiring harness. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.Note: Refer to the Electrical System Schematic for further information about the machine wiring.Expected Result:All connectors, pins, and sockets should be completely inserted and coupled. The harness and wiring should be free of corrosion, abrasion, and pinch points.Results:
OK - Proceed to Test Step 3.
Not OK - Repair: Repair the circuit.Verify that the repair eliminates the problem. Stop.Test Step 3. Check the Resistance of the ATA Data Link
Illustration 2 g00938667
J1/P1 Breakout
Illustration 3 g00755883
Service Tool Connector
Turn the keyswitch to the OFF position.
Disconnect the J1/P1 ECM connector.
Measure the resistance between P1:1 (ATA Data Link (-)) and P1:7 (ATA Data Link (+)).Note: Resistance should be greater than 20,000 ohms.
Install a jumper wire with Deutsch sockets on each end between J42:J and J42:H.
Measure the resistance between P1:1 (ATA Data Link (-)) and P1:7 (ATA Data Link (+)).Note: Resistance should be less than 10 ohms.
Remove the jumper wire and reconnect the J1/P1 ECM connector.Expected Result:Resistance should be less than 10 ohms when the jumper wire is installed. The resistance should be greater than 20,000 ohms, when the jumper wire is removed.Results:
OK - There does not appear to be a problem with the ATA data link at this time.Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent. Stop.
Not OK - There is either an open circuit or a short circuit in the ATA data link.Repair: Repair the circuit.Verify that the repair eliminates the problem. Stop.Test Step 4. Change the Electronic Service Tool Components
Use the same electronic service tool components and attempt to connect to another Caterpillar electronic engine.
If another engine is not available, find a different communication adapter and find a different set of electronic service tool cables. Ensure that the communication adapter and cables are a complete set. Connect the electronic service tool to the service tool connector with the new communication adapter and cables.
Turn the ignition key switch to the ON position. Determine if the electronic service tool communicates correctly with the engine.
If changing the communication adapter and cables causes the electronic service tool to properly communicate, use the following procedure:
Replace the new communication adapter and cables with the old communication adapter and cables by changing one component at a time.
Repower the electronic service tool after each component is changed. Use this method until you find the faulty component.Results:
Result 1 - The original communication adapter and cables work on another engine. Repair: The electronic service tool is working properly.Refer toTroubleshooting, "Electrical Connectors - Inspect". Stop.
Result 2 - A different communications adapter and cables work on the original engine. Repair: The original electronic service tool components are not working properly.Repair the electronic service tool component that is faulty. If a repair is not practical, replace the faulty electronic service tool component. Stop.


Parts reverse Force:

F85300
 
F85300 REVERSE LOCK SPRING
H0709B79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H82E, H0850H81C, H0851X88A, H0853F88B, H0856A89A, H0856B80H, H0856C87A, H0856C87B, H0856F84A, H0856F85A, H0856F86A, H0856H82K, H0857B78F, H0857H79G, H0858C84
F177350
 
F177350 REVERSE LOCK PIN
H0709B79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H82E, H0850H81C, H0851X88A, H0853F88B, H0856A89A, H0856B80H, H0856C87A, H0856C87B, H0856F84A, H0856F85A, H0856F86A, H0856H82K, H0857B78F, H0857H79G, H0858C84
F369364
REVERSE LOCK ARM
F369364 REVERSE LOCK ARM
H0709B79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H82E, H0850H81C, H0851X88A, H0853F88B, H0856A89A, H0856B80H, H0856C87A, H0856C87B, H0856F84A, H0856F85A, H0856F86A, H0856H82K, H0857B78F, H0857H79G, H0858C84
Back to top