13194 Force RING-Retaining


13194 RING-Retaining Force H0407E92C, H0706A91B, H075312SD, H075312UD, H075412VD, H090312RD, H0903E91H, H090412SD, H090412UD, H090422VD, H1201A90A, H120412RD, H120412SD, H120412UD, H1501E89A RING
13194 RING-Retaining Force
Rating:
93

Buy RING-Retaining 13194 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Force entire parts catalog list:

H0407E92C 1992,1993,1994
H0706A91B 1991,1992,1993,1994,1995
H075312SD 1996,1997
H075312UD 1998
H075412VD 1999
H090312RD 1995
H0903E91H 1991,1992,1993,1994
H090412SD 1996,1997
H090412UD 1998
H090422VD 1999
H1201A90A 1990,1991,1992,1993,1994
H120412RD 1995
H120412SD 1996,1997
H120412UD 1998,1999
H1501E89A 1989,1990,1991,1992,1993,1994

Information:

Problem 1: Engine Crankshaft Will Not Turn When Ignition Switch Is On.
Engine Crankshaft Will Not Turn When Ignition Switch Is On Probable Cause(s):1. Low or no battery voltage: Check battery voltage. If battery voltage is less than 8 volts for a 12 volt system, or 16 volts for a 24 volt system, put a charge on the battery. If battery will not hold a charge, load test the battery as shown in the Electrical System of the Testing And Adjusting Section of this Service Manual.2. Defective switch, defective wiring or connection in switch circuit: With ignition switch in the "START" position, check voltage at switch connection on starter solenoid. If there is no voltage, or if the voltage is low at this connection and there is good voltage at the battery, check for a defective cable or connection between the battery and the starter.3. Defective cable or connection (battery to starter) With ignition switch in the "START" position, check voltage at connection of battery cable to starter. If there is no voltage, or if the voltage is low at this connection and there is good voltage at the battery, check for a defective cable or connection between the battery and the starter.4. Defective starter solenoid: Remove and repair or replace a solenoid which does not work when voltage is correct at both the battery and ignition switches connections.5. Defective starter motor: If the solenoid works and the starter motor does not turn the crankshaft, the starter motor is defective. Before removing the starter motor, turn the crankshaft by hand to be sure a mechanical failure inside the engine, transmission, or power take-off is not preventing the crankshaft from turning. If the crankshaft turns freely by hand, engage the starter motor again. If the starter motor still will not work, remove the starter motor. Repair or replace the starter motor.6. Transmission or power take-off (if equipped) problem prevents crankshaft from turning: If the crankshaft cannot be turned by hand, disconnect the transmission and the power take-off. If the crankshaft will now turn, find the cause of the problem in the transmission or power take-off and make necessary corrections.7. Inside problem prevents crankshaft from turning: If the crankshaft cannot be turned after disconnecting the transmission and/or the power take-off, remove the fuel nozzles and check for fluid in the cylinders while turning the crankshaft. If fluid in the cylinders is not the problem, the engine must be disassembled to check for other internal problems. Some of the possible problems are bearing seizure, piston seizure, and valves making contact with the pistons.Problem 2: Engine Hard To Or Will Not Start.
Engine Hard To Or Will Not Start Engine Crankshaft Turns Too Slowly.
Probable Cause(s):1. Low battery voltage: Check battery voltage. If battery voltage is less than 8 volts for a 12 volt system, or 16 volts for a 24 volt system, put a charge on the battery. If battery will not hold a charge, load test the battery as shown in the Electrical System of the Testing And Adjusting Section of this Service Manual.2. Defective cable or connection (battery to starter) With ignition switch in the "START" position, check voltage at connection of battery cable to starter. If there is no voltage, or if the voltage is low at this connection and there is good voltage at the battery, check for a defective cable or connection between the battery and the starter.3. Oil too thick for free crankshaft rotation: Use the recommended Lubrication Viscosities as found in the Operation And Maintenance Guide.4. Defective starter motor: Remove and test starter motor. Make repairs as necessary or install a new starter motor.5. Extra outside loads: Damage to the power take-off equipment (if equipped) and/or transmission can put extra load on the engine. This prevents free rotation of the crankshaft. To check, disconnect the transmission and power take-off, and start the engine.6. Mechanical problem inside engine: Take the engine apart and check all components for damage.Problem 3: Engine Hard To Or Will Not Start. Engine Crankshaft Turns Freely
Engine Hard To Or Will Not Start Exhaust Smoke Can Be Seen While Starting
Probable Cause(s):1. Cold outside temperature: It may be necessary to use starting aids, or to heat engine oil or coolant at temperature below 10 °C (50 °F).2. Slow cranking speed: Cranking speed must be at least 100 rpm. Check the condition of the starting system.3. Air in the fuel system: With air in the fuel system the engine will normally be difficult to start, run rough and release a large amount of white smoke. To remove the air from the fuel system, loosen the return line to the fuel tank and put 35 kPa (5 psi) of air pressure to the fuel tank.
Do not use more than 55 kPa (8 psi) of air pressure in the fuel tank or damage to the tank may result.
Check for leaks at the connections between the fuel tank and the transfer pump. If leaks are found, tighten the connections or replace the lines. If there are no visual leaks, remove the fuel supply line from the tank and connect to an outside fuel supply. If this corrects the problem, the suction (standpipe) inside of the fuel tank has a leak.4. Low quality fuel: Remove a small amount of fuel from the tank and check for water in the fuel. If there is water in the fuel, remove fuel from the tank until the tank is free of water. Change the fuel filter and fill the fuel tank with a good quality fuel. The fuel priming pump (if equipped) may be used to fill the fuel filter and fuel gallery (in the cylinder head), from the fuel tank before the engine is started. If there is no water in the fuel, start the engine by using an outside source of fuel. If engine starts correctly using different fuel, remove all fuel from the tank and fill with a good quality fuel.5. Low fuel pressure: At starting rpm, the minimum fuel pressure


Parts ring Force:

FT8926
 
FT8926 RING EXPANDER
H0032H84G, H0033H75C, H0042081C, H0042082D, H0042083E, H0042B80G, H0042C84L, H0042H79F, H0043F85A, H005201SD, H005201TS, H0052C88A, H0054H76D, H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0062H79M, H0064H78D, H0064H80F, H0064H82
FT2996
 
FT2996 RING COMPRESSOR
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0352H77H, H0352H79L, H0353E91A, H0353E91B, H0353H78K, H0353H80
F10210
RING
F10210 RING
H0407E92C, H0504H88C, H0504H88D, H0504P89B, H0507B85A, H0507C86A, H0507C87A, H0507C87C, H0507C88B, H0507F87B, H0507F88A, H0507Z89B, H1501E89A
F660411
 
F660411 RING (RETAINING)
H0257F88A, H0257F88B, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0357C88B, H0357F88A, H0357F89C, H0357G90A, H0407E92C, H0504H88C, H0504H88D, H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91
FSA663260
 
FSA663260 RING SET (.010 OVER)
H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507E91B, H0507Z89B, H0853F89C, H0853F89E, H0853F89F, H0853F89G, H0856A89H, H0856L89D, H085LD89A, H085LD89B, H085LD89C, H0906A90A, H090LD90
828565A 1
 
828565A 1 RING SET (2 Rings) (STANDARD) SEE
H040312SD, H075312SD, H090412SD, H120412SD
828565A 2
 
828565A 2 RING SET (2 Rings) (.015 O.S.) NOTE
H040312SD, H075312SD, H090412SD, H120412SD
828565A 3
 
828565A 3 RING SET (2 Rings) (.030 O.S.) BELOW
H040312SD, H075312SD, H090412SD, H120412SD
Back to top