828564A 1 Force RING SET (2 Rings)


828564A 1 RING SET (2 Rings) Force H075312UD, H090412UD, H090422VD RING
828564A 1 RING SET (2 Rings) Force
Rating:
58

Buy RING SET (2 Rings) 828564A 1 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 21
 

Compatible models:

Force entire parts catalog list:

H075312UD 1998
H090412UD 1998
H090422VD 1999

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     150-3992     Timing Pin (1)     1    
150-3993 Timing Pin (2)     1    
( 1 ) The timing pin is required in order to install Bosch fuel injection pumps.
( 2 ) The timing pin is required in order to install Lucas and Stanadyne fuel injection pumps.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00567719
Typical example
Check the condition of O-ring seal (1) from fuel injection pump (2). If the seal is worn or damaged, use a new part for replacement.
Lightly lubricate O-ring seal (1) with clean engine oil. Install O-ring seal (1) on fuel injection pump (2) .
The number 1 cylinder must be at the top center position on the compression stroke before the fuel injection pump is installed. If the crankshaft needs to be rotated, the fuel injection pump must be mounted temporarily or the loose gear could cause damage to the front housing.
Illustration 2 g00567718
Typical example
Put fuel injection pump (2) in position on the engine. Ensure that the timing gear is aligned with the hub of fuel injection pump (2). Install three nuts (3) and tighten the nuts to a torque of 28 N m (21 lb ft).
Illustration 3 g00567717
Typical example
Illustration 4 g00567737
Typical example
Position gear (5) on the shaft of the fuel injection pump.
Put the timing gear plate in position and install four bolts (4). Tighten the four bolts finger tight.Note: The fuel injection pump gear will only fit in one position. Install the gear with the letters "C" and "M" facing away from the engine.Note: The location of Tool (A) for Bosch fuel injection pumps will be located toward the top of the fuel injection pump. The location of Tool (A) for Lucas and Stanadyne fuel injection pumps will be located toward the bottom of the fuel injection pump.
Install Tool (A) through hole (6) in the timing gear and hole (7) in the hub. Push Tool (A) into position in hole (8) in the fuel injection pump body. If Tool (A) can be fully seated, the fuel injection pump timing is correct. No resistance should be felt when the timing pin is inserted into hole (8) of the fuel injection pump body.
The fuel injection pump may be supplied with the fuel injection pump shaft in the locked position. The drive shaft of the fuel injection pump must not be rotated without the spacer in position under the locking screw. Damage to the drive shaft of the fuel injection pump will result.
When the timing plate is installed, rotate gear (5) by hand in a counterclockwise direction in order to remove the backlash between gear (5) and the idler gear. Do not rotate the crankshaft or the fuel injection pump shaft. Tighten bolts (4) to a torque of 28 N m (21 lb ft).
Remove Tool (A) from the fuel injection pump gear.End By:
Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install".
Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".


Parts ring Force:

FT2996
 
FT2996 RING COMPRESSOR
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0352H77H, H0352H79L, H0353E91A, H0353E91B, H0353H78K, H0353H80
12576
 
12576 RING-Thrust
H075412VD, H090312RD, H0903E91H, H090412SD, H090412UD, H090422VD, H1201A90A, H120412RD, H120412SD, H120412UD, H1501E89A
13194
 
13194 RING-Retaining
H0407E92C, H0706A91B, H075312SD, H075312UD, H075412VD, H090312RD, H0903E91H, H090412SD, H090412UD, H090422VD, H1201A90A, H120412RD, H120412SD, H120412UD, H1501E89A
F749208
 
F749208 RING, RETAINING
H0407E92C, H0507A91C, H0507E91B, H0706A91B, H075312SD, H075312UD
67684
 
67684 RING, Retaining
H075412VD, H090312RD, H090412SD, H090412UD, H090422VD, H120412RD, H120412SD, H120412UD
52035
 
52035 RING-Lock
H040312SD, H040312UD, H075312SD, H075312UD, H075412VD, H090412SD, H090412UD, H090422VD, H120412SD, H120412UD
828564A 2
 
828564A 2 RING SET (2 Rings)
H075312UD, H090412UD, H090422VD
828564A 3
 
828564A 3 RING SET (2 Rings)
H075312UD, H090412UD, H090422VD
Back to top