FSA463260 Force RING SET (.010 OVERSIZE) 2 RINGS PER SET


FSA463260 RING SET (.010 OVERSIZE) 2 RINGS PER SET Force H0257F88A, H0257F88B, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0357C87A, H0357C88B, H0357F88A, H0357F89C, H0357G90A RING
FSA463260 RING SET (.010 OVERSIZE) 2 RINGS PER SET Force
Rating:
43

Buy RING SET (.010 OVERSIZE) 2 RINGS PER SET FSA463260 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

Force entire parts catalog list:

H0257F88A 1988,1989
H0257F88B 1988,1989,1991
H0352F90B 1990
H0352F90C 1990
H0353E91A 1991
H0353E91B 1991
H0355D89A 1989
H0356F89B 1989
H0357C87A 1987
H0357C88B 1988
H0357F88A 1988
H0357F89C 1989
H0357G90A 1990

Information:

Operation
Under certain operating conditions, it could be dangerous to have the marine propulsion engine stop unexpectantly. Examples of such conditions are: Docking, passing bridge abutments, and locking through a lock-and-dam. Marine engines are usually equipped with various alarm systems which will warn the operator when an abnormal engine operating condition is arising. When an alarm is activated, corrective measures should be taken before the situation becomes an emergency. If corrective measures are not taken in reasonable time, engine damage may result; or if equipped, a corresponding shutoff device will stop the engine.Each alarm switch is electrically connected to an indicating light, bell or horn. The alarm will continue until the condition is corrected and then the light, bell or horn will turn off.To silence the bell or horn while repairs are being made, a two-way switch and a red indicator light may be installed. When the alarm is turned OFF, the red indicator light will light.
If the switch is left in the OFF position after the repairs have been made, the red light will indicate the engine is not protected.
Testing
Most control panels are equipped with a test switch. By turning the switch ON, all of the indicator lights can be checked for proper operation. Test the indicator lights periodically, replace burned-out light bulbs immediately.
TEST SWITCH AND LIGHTSAll alarms on the engine should be checked twice a year for proper operation by authorized dealer personnel. Abnormal operating conditions must be simulated which could cause engine damage if the tests are incorrectly performed.
ENGINE JACKET WATER TEMPERATURE SWITCH
INLET AIR TEMPERATURE SWITCH - Left Bank
INLET AIR TEMPERATURE SWITCH - Right Bank.
MARINE GEAR OIL TEMPERATURE SWITCH
ENGINE OIL PRESSURE SWITCH
ENGINE JACKET WATER LEVEL SWITCH
ENGINE OIL PRESSURE SWITCH AND OIL PRESSURE ALARM SWITCHAlarm Systems And Troubleshooting
Listed below are the different alarm systems usually found on an engine. Several causes for the alarm to function are listed, followed by possible corrective measures which should be performed. Additional measures may be required by the operator depending upon the circumstances and conditions present. On multi-engine powered vessels, one engine may be shut down for repairs while proceeding at reduced power on the remaining engine(s).An authorized Caterpillar dealer should analyze major engine problems.High Engine Jacket Water Temperature Alarm:
This alarm switch is usually installed in the water temperature regulator housing on all engines. If the alarm sounds, check to see if any of the following conditions have occurred. High Inlet Air Temperature Alarm:
This alarm switch is used on 6.25 inch (159 mm) and 5.4 inch (137 mm) bore V-engines equipped with 85°F (29°C) sea water aftercooling. The switch is mounted in the inlet manifold after the aftercooler. If this alarm sounds, check the following: High Oil Temperature Alarm:
This alarm is installed on all Caterpillar 7200 Series Marine Gear and most V-engines. The switch is located in the oil line between the oil pump and oil strainer or oil filter. If this alarm sounds, check the following: Low Oil Pressure Alarm:
This alarm switch is usually mounted on the side of the engine block with oil lines connected to the switch. If this alarm sounds, check the following:


Parts ring Force:

FT8926
 
FT8926 RING EXPANDER
H0032H84G, H0033H75C, H0042081C, H0042082D, H0042083E, H0042B80G, H0042C84L, H0042H79F, H0043F85A, H005201SD, H005201TS, H0052C88A, H0054H76D, H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0062H79M, H0064H78D, H0064H80F, H0064H82
FT2996
 
FT2996 RING COMPRESSOR
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0352H77H, H0352H79L, H0353E91A, H0353E91B, H0353H78K, H0353H80
818120A 1
 
818120A 1 RING SET (.030 OVERSIZE) 2 RINGS PER SET
H0257F88A, H0257F88B, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0357C87A, H0357C88B, H0357F88A, H0357F89C, H0357G90A
F660411
 
F660411 RING (RETAINING)
H0257F88A, H0257F88B, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0357C88B, H0357F88A, H0357F89C, H0357G90A, H0407E92C, H0504H88C, H0504H88D, H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91
Back to top