F694615 ROD, INTERMEDIATE SHIFT Force
H0853F89F, H0853F89G, H0856A89H, H0856L89D, H0903E91H, H0906A90A, H1201A90A, H1251A89D, H1251A89E, H1501E89A
ROD
Price: query
Compatible models:
Force entire parts catalog list:
- GEAR HOUSING » F694615
- GEAR HOUSING » F694615
- GEAR HOUSING » F694615
- GEAR HOUSING » F694615
- GEAR HOUSING » F694615
H1201A90A 1990,1991,1992,1993,1994
- GEAR HOUSING » F694615
- GEAR HOUSING » F694615
- GEAR HOUSING » F694615
- GEAR HOUSING » F694615
Information:
1. Remove bolt (2) that holds suction bell (4) to the oil pan plate.2. Remove bolts (1) that hold the oil pump to the scavenge tube. Remove the gasket. Bend the locks away from bolts (3). Remove bolts (3) that hold the suction tube to the oil pump. Remove the gasket from between the suction tube flange and the oil pump. The suction tube, suction bell and oil pump can be removed as a unit. 3. Bend the locks away from bolts (6) that hold the oil pump to the cylinder block. Remove bolts (6).4. Remove oil pump (5). Weight is 14 kg (30 lbs). The following steps are for the installation of the oil pump.5. Put oil pump (5) in position under the cylinder block. Install a new gasket between the oil pump and the scavenge tube. Install bolts (1) that hold the oil pump to the scavenge tube.6. Install bolts (6), the washers and the locks that hold the oil pump to the cylinder block.7. Put suction bell (4) in position on the oil pump. Make sure there is a new gasket between the flange on the oil tube and the oil pump.8. Install bolts (3) that hold the suction tube to the oil pump. Bend the locks against the bolts. Install the bolt that holds the bracket on the suction bell to the oil pan plate. Install bolt (2).End By:a. install oil panDisassemble Oil Pump
Start By:a. remove oil pump 1. Remove idler gear (2). Remove the bearing from the idler gear with Tooling (B).2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with Tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), the keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with Tooling (B).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with Tooling (B) and a press as follows: a. Put bearings (9) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is 1.52 mm (.060 in) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30 15 degrees from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores. 2. Install the bearings in oil pump body assembly with Tooling (B) and a press as follows. a. Put bearings (10) in position on the inside of the oil pump body assembly with the chamber on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump at an angle of 30 15 degrees from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See the topic "Oil Pump" in the Specifications Manual.4. Put clean engine oil on all the parts of the oil pump. 5. Install pressure relief valve (11) cover (12) and bolt (6) in the oil pump body assembly. 6. Install shaft assemblies (13) in the oil pump body assembly.7. Install spacer (4). Install the key in the shaft assembly.8. Install the two gears on the shaft assemblies. 9. Install scavenge pump body assembly (14) and the bolts that hold it.10. Install key (15), drive gear (16), the washer and bolt (17). Tighten the bolt to a torque of 43 7 N m (32 5 lb ft).11. Install the bearing in the idler gear with Tooling (B) and a press until it is even with the outside surface of the gear.12. Install the suction bell on the oil pump. Install the idler gear on the oil pump.
The oil pump must turn freely by hand after it is assembled.
End By:a. install oil pump
Start By:a. remove oil pump 1. Remove idler gear (2). Remove the bearing from the idler gear with Tooling (B).2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with Tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), the keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with Tooling (B).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with Tooling (B) and a press as follows: a. Put bearings (9) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is 1.52 mm (.060 in) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30 15 degrees from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores. 2. Install the bearings in oil pump body assembly with Tooling (B) and a press as follows. a. Put bearings (10) in position on the inside of the oil pump body assembly with the chamber on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump at an angle of 30 15 degrees from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See the topic "Oil Pump" in the Specifications Manual.4. Put clean engine oil on all the parts of the oil pump. 5. Install pressure relief valve (11) cover (12) and bolt (6) in the oil pump body assembly. 6. Install shaft assemblies (13) in the oil pump body assembly.7. Install spacer (4). Install the key in the shaft assembly.8. Install the two gears on the shaft assemblies. 9. Install scavenge pump body assembly (14) and the bolts that hold it.10. Install key (15), drive gear (16), the washer and bolt (17). Tighten the bolt to a torque of 43 7 N m (32 5 lb ft).11. Install the bearing in the idler gear with Tooling (B) and a press until it is even with the outside surface of the gear.12. Install the suction bell on the oil pump. Install the idler gear on the oil pump.
The oil pump must turn freely by hand after it is assembled.
End By:a. install oil pump
Parts rod Force:
F98273
F98273 ROD END CONNECTOR STUD
H0064H80F, H0075H79A, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0095B80F, H0095B81
F500615-1
F500615-1 ROD, GEAR SHIFT UPPER (25 INCH MODELS)
H0853F89C, H0853F89E, H0853F89F, H0853F89G, H0856A89H, H0856L89D, H0856Y89B, H0903F90B, H0903F90C, H0903F91A, H0903F91C, H0906A90A, H1251A89A, H1251A89B, H1251A89C, H1251A89D, H1251A89E
F694705
F694705 ROD, LOWER SHIFT
H0853F89F, H0853F89G, H0856A89H, H0856L89D, H085LD89A, H085LD89B, H085LD89C, H0903E91H, H0906A90A, H090LD90A, H1201A90A, H120LD90A, H1251A89D, H1251A89E, H125LD89A, H125LD89B, H1501E89A
F523705-1
F523705-1 ROD-Lower Gear Shift
H0903E91D, H0903E91H, H0903F91A, H0903F91C, H0906A90A, H1201A90A, H120LD92B, H1501E89A
F500615-2
F85445-1
F85445-1 ROD-Spark Control
H0706A91B, H075312SD, H075312UD, H075412VD, H090312RD, H0903E91D, H0903E91H, H090412SD, H090412UD, H090422VD, H090LD90B, H090LD91D, H1201A90A, H120412RD, H120412SD, H120412UD, H120LD91B, H120LD91D, H120LD92B, H1501E89A
F2A654017
F2A654017 ROD ASSEMBLY
H0903E91D, H0903E91H, H0903F90B, H0903F90C, H0903F91A, H0903F91C, H0906A90A, H1201A90A, H1501E89A