F269316 Force ROLLER SHAFT


F269316 ROLLER SHAFT Force H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0095B80F, H0095B81G, H0095H82H, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79 ROLLER
F269316 ROLLER SHAFT Force
Rating:
83

Buy ROLLER SHAFT F269316 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

Force entire parts catalog list:

H0060B76A 1976
H0062H79M 1979
H0064H78D 1978
H0082H76G 1976,1977
H0082H79K 1979
H0091B80B 1980
H0091H79A 1979
H0091H83C 1983
H0091H84D 1984
H0092B80G 1980
H0092H79F 1979
H0092H81H 1981
H0092H81J 1981,1982
H0092H83K 1983
H0092H84L 1984
H0095B80F 1980
H0095B81G 1981
H0095H82H 1982
H0101B78A 1978
H0102H76C 1976,1977
H0102H78E 1978
H0121B79A 1979
H0122H79E 1979
H0125H79E 1979
H0152H79E 1979
H0152H80F 1980
H0152H81G 1981

Information:


This engine uses high voltage to control the fuel injectors.Disconnect electronic fuel injector enable circuit connector to prevent personal injury.Do not come in contact with the fuel injector terminals while the engine is running.
Note: Valve lash is measured between the rocker arm and the valve bridge. All measurements and adjustments must be made with the engine stopped and the valves fully closed.Valve Lash Check
An adjustment is not necessary if the measurement of the valve lash is in the acceptable range. Check the valve lash while the engine is stopped. The range is specified in Table 1.
Table 1
Quick Reference for Engine Valve Lash Setting
Inlet Valves Exhaust Valves
Valve Lash Setting 0.38 0.08 mm (0.015 0.003 inch) 0.76 0.08 mm (0.030 0.003 inch)
TC Compression Stroke of No. 1 Piston 1-2-3-7-8-10 1-2-5-6-9-10
TC Compression Stroke of No. 11 Piston(1) 4-5-6-9-11-12 3-4-7-8-11-12
Firing Order 1-10-9-6-5-12-11-4-3-8-7-2(2)
(1) 360° from TC compression stroke
(2) Refer to Illustration 1 in order to locate the No. 1 cylinder.If the measurement is not within this range adjustment is necessary. Refer to "Valve Lash Adjustment".Valve Lash Adjustment
Illustration 1 g01386737
(A) Inlet valves
(B) Exhaust valves
(C) Left side of the engine
(D) Cylinder number
(E) Flywheel end of the engine
(F) Front of the engine
(G) Right side of the engine
Illustration 2 g01386742
Typical example
(1) Valve adjustment locknut
(2) Exhaust adjustment screw
(3) Valve adjustment locknut
(4) Inlet adjustment screw
(5) Feeler gauge
Table 2
Valve Lash
Valves Thickness of Gauge
Inlet 0.38 mm (0.015 inch)
Exhaust 0.76 mm (0.030 inch) Adjust the valve lash while the engine is stopped. Use the following procedure in order to adjust the valves:
Put the No. 1 piston at the top center position. Note: See Testing and Adjusting, "Finding Top Center Position for the No. 1 Piston" for further details.
With No. 1 piston at the top center position of the compression stroke, an adjustment can be made to the valves. Before any adjustments are made, lightly tap each rocker arm at the top of the adjustment screw. Use a soft mallet to ensure that the lifter roller seats against the camshaft's base circle.
Make an adjustment to the valve lash on the inlet valves for cylinders 1, 2, 3, 7, 8, and 10.
Loosen valve adjustment locknut (3).
Place the appropriate feeler gauge (5) between the inlet rocker arm and the inlet valve bridge. Turn inlet adjustment screw (4) while valve adjustment locknut (3) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (3) while valve adjustment screw (4) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Make an adjustment to the valve lash on the exhaust valves for cylinders 1, 2, 5, 6, 9, and 10.
Loosen valve adjustment locknut (1).
Place the appropriate feeler gauge (5) between the exhaust rocker arm and the exhaust valve bridge. Turn exhaust adjustment screw (2) while valve adjustment locknut (1) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (1) while valve adjustment screw (2) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Remove the timing bolt, and turn the flywheel by 360 degrees in the direction of engine rotation. This will position the No. 11 piston at the top center at the beginning of the compression stroke. Install the timing bolt in the flywheel.
Make an adjustment to the valve lash on the inlet valves for the following cylinders 4, 5, 6, 9, 11, and 12.
Loosen valve adjustment locknut (3).
Place the appropriate feeler gauge (5) between the inlet rocker arm and the inlet valve bridge. Turn inlet adjustment screw (4) while valve adjustment locknut (3) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (3) while valve adjustment screw (4) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Make an adjustment to the valve lash on the exhaust valves for cylinders 3, 4, 7, 8, 11, and 12.
Loosen valve adjustment locknut (1).
Place the appropriate feeler gauge (5) between the exhaust rocker arm and the exhaust valve bridge. Turn exhaust adjustment screw (2) while valve adjustment locknut (1) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (1) while valve adjustment screw (2) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Remove the timing bolt from the flywheel after all valve lash adjustments have been made.


Parts roller Force:

F92759
 
F92759 ROLLER
H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0094H81F, H0095B80F, H0095B81G, H0095H82H, H0101B78A, H0102H76C, H0102H78E, H0121B79
F78318
 
F78318 ROLLER
H0033H75C, H0091B80B, H0091H79A, H0092B80G, H0092H79F, H0092H81H, H0095B81G, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0125H79E, H0152B78D, H0152H79E, H0152H80F, H0152H81G
F286571
 
F286571 ROLLER SET, MAIN BEARING (26 PER SET)
H0054H76D, H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0062H79M, H0064H78D, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H79B, H0072H80C, H0072H82E, H0075H79A, H0082H76
318318
 
318318 ROLLER, THROTTLE CAM FOLLOWER
H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K
F286228
 
F286228 ROLLER SET, CONNECTING ROD (26 PER SET)
H0102H76C, H0102H78E, H0152B78D
Back to top