40019104 Force SCREW (M5 X 8)


40019104 SCREW (M5 X 8) Force H040312RD, H040312SD, H040312UD, H075412VD, H090312RD, H090412SD, H090412UD, H090422VD, H120412RD, H120412SD, H120412UD SCREW
40019104 SCREW (M5 X 8) Force
Rating:
63

Buy SCREW (M5 X 8) 40019104 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 28
 

Force entire parts catalog list:

H040312RD 1995
H040312SD 1996,1997
H040312UD 1998,1999
H075412VD 1999
H090312RD 1995
H090412SD 1996,1997
H090412UD 1998
H090422VD 1999
H120412RD 1995
H120412SD 1996,1997
H120412UD 1998,1999

Information:


The Engine Monitoring System is not a guarantee against catastrophic failures. Programmed delays and derate schedules are designed to minimize false alarms and provide time for the operator to stop the engine.
Programmable features monitor the following conditions:
Coolant temperature
Oil pressure
Inlet manifold air temperature (if equipped)
Cooling system level (if equipped)
Fuel temperature
Fuel pressure (if equipped)Coolant Level Sensor (If Equipped)
Note: The coolant level sensor is an optional feature.The system can be programmed with one of the following options:"ENABLED" - The system will monitor the input from the coolant level sensor. The system is programmed to this value when the engine is shipped by Caterpillar."DISABLED" - The system will not monitor the input from the coolant level sensor.Programmable Options and Systems Operation
If the Warning/Derate/Shutdown mode has been selected and the warning indicator activates, bring the engine to a stop whenever possible. Depending on the application, special precautions should be taken to avoid personal injruy.
The engine can be programmed to the following modes:
"OFF"
"Warning"
"Warning/Derate"
"Warning/Derate/Shutdown""Warning"
The "DIAGNOSTIC" lamp and the warning signal (red lamp or buzzer) turn "ON" and the warning signal is activated continuously in order to alert the operator that one or more of the engine parameters is not within normal operating range."Warning/Derate"
The "DIAGNOSTIC" lamp turns "ON" and the warning signal (red lamp or buzzer) is activated. After the warning, the engine will derate rpm and power. The warning lamp will begin to flash when the derating occurs.When the engine is fully derated, the engine power is limited to 120 kW (160 hp). During a low oil pressure condition, the engine can be limited to 1350 rpm."Warning/Derate/Shutdown"
The "DIAGNOSTIC" lamp turns "ON" and the warning signal (red lamp or buzzer) is activated. After the warning, the engine will derate rpm and power. The engine will continue to derate rpm until a shutdown of the engine occurs. The engine can be restarted after a shutdown for use in an emergency.A shutdown of the engine may occur in as little as 20 seconds. The engine can be restarted after a shutdown for use in an emergency. However, the cause of the initial shutdown may still exist. The engine may shut down again in as little as 20 seconds.If there is a signal for coolant loss, there will be a 10 second delay in order to verify the condition. The system will derate the engine rpm for 40 seconds before the engine will shut down if the engine has been programmed to shut down.If there is a signal for low oil pressure or for coolant temperature, there will be a two second delay in order to verify the condition. The system will derate the engine rpm for 30 seconds before the engine will shut down if the engine has been programmed to shutdown.For more information or assistance for repairs, consult your Caterpillar dealer.Note: The Customer Specified Parameters may be secured by customer passwords. The engine may have all of the parameters that are programmed or any combination of the parameters that are programmed. Refer to the Operation and Maintenance Manual, "Customer Specified Parameters" topic (Product Information Section) for more information on the programmed parameters of the engine. Refer to the Electronic Troubleshooting for more information.


Parts screw Force:

F901938-1
 
F901938-1 SCREW, CYLINDER HEAD
H0032H84G, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0054H76D, H0060B76A, H0060B78B, H0060H79C, H0060H80
F2228
 
F2228 SCREW, CRANKCASE COVER TO CYLINDER 3/8 - 16 X 3 AT UPR MAIN
H040312RD, H040312SD, H0407E92C, H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507Z89B, H1501E89A
19926100
 
19926100 SCREW (#10-24 x 1.00)
H040312RD, H040312SD, H040312UD, H0407E92C, H0706A91B, H075312SD, H075312UD, H075412VD, H090312RD, H0903E91H, H090412SD, H090412UD, H090422VD, H1201A90A, H120412RD, H120412SD, H120412UD, H1501E89A
824832 4
 
824832 4 SCREW (M6 x 1 x 16MM)
H025201RD, H025201TD, H025201TS, H025201US, H040312RD, H040312SD, H040312UD, H0706A91B, H075312SD, H075312UD
40056105
 
40056105 SCREW (M5 X 10)
H040312RD, H040312SD, H040312UD
40003 80
 
40003 80 SCREW (M10 X 45)
H040312RD, H040312SD, H040312UD
40107 50
 
40107 50 SCREW (M8 x 50)
H075412VD, H090312RD, H090412SD, H090412UD, H090422VD, H120412RD, H120412SD, H120412UD
853652
 
853652 SCREW (.250-20 x 1.125)
H040312SD, H040312UD, H075312SD, H075312UD, H075412VD, H090412SD, H090412UD, H090422VD, H120412SD, H120412UD
Back to top