41772 Force SCREW (10-24 X 1/2")


41772 SCREW (10-24 X 1/2") Force H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0407E92C, H0706A91B, H0903E91H, H1201A90A, H1501E89A SCREW
41772 SCREW (10-24 X 1/2") Force
Rating:
58

Buy SCREW (10-24 X 1/2") 41772 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

Force entire parts catalog list:

H005201RS 1995
H005201SD 1996,1997
H005201TS 1997
H005201UD 1998,1999
H0052C88A 1988,1989,1990,1991,1992,1993,1994,1995
H0407E92C 1992,1993,1994
H0706A91B 1991,1992,1993,1994,1995
H0903E91H 1991,1992,1993,1994
H1201A90A 1990,1991,1992,1993,1994
H1501E89A 1989,1990,1991,1992,1993,1994

Information:


Table 1
Event Code
Code Conditions which Generate this Code System Response
E021(2) High Exhaust Temperature Derate The exhaust temperature is above the trip point temperature. The engine is derated. The code is logged. Probable Causes
Diagnostic codes
Air inlet and exhaust system
Boost pressure below normal
Fuel supply or fuel pressure
Differential exhaust temperature is too high.
Aftercooler
Valve adjustment
Accessory equipment
TurbochargerRecommended Actions
Diagnostic Codes
Connect Cat ET in order to determine if any diagnostic codes for the injector solenoids are present. Repair any active diagnostic codes.Perform the "Injector Solenoid Test". Observe that the injector solenoids are being energized on Cat ET. Listen for an audible click at the valve covers as each injector is energized.Perform the "Cylinder Cutout Test". Analyze the data in order to determine if one of the injectors is misfiring. Refer to Troubleshooting, "Injector Solenoids".Air Inlet and Exhaust System
Check the air inlet manifold pressure. Use a VIMS boost trend to aid in this diagnosis. Check for air inlet restrictions and/or leaks. Refer to the Systems Operation/Testing and Adjusting manual for more information. Refer to Service Magazine, SEPD0712, "Procedure to Test the Air Induction System".Check for leaks between the exhaust manifold and the turbocharger. Check for exhaust restrictions. Refer to the Systems Operation/Testing and Adjusting manual for more information.Boost Pressure Below Normal
Ensure that the turbocharger is operating correctly. Periodic inspection and cleaning is recommended for the turbocharger compressor housing (inlet side). Any fumes from the crankcase are filtered through the air inlet system. Therefore, by-products from oil and from combustion can collect in the turbocharger compressor housing. Over time, this buildup can contribute to loss of engine power, increased black smoke and overall loss of engine efficiency.Fuel Supply or Fuel Pressure
Check the fuel level in the fuel tank. Ensure that adequate fuel is available for the application.Check the fuel lines for restrictions and for collapsed lines or pinched lines. Repair the lines and/or replace the lines.Check the fuel tank for foreign objects which may block the fuel supply. Check for air leaks in the suction line of the fuel pump. Prime the fuel supply system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuit
Replacement of unit injectorsCold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.Check the fuel pressure during engine operation. Check the fuel pressure after the fuel filter. Refer to the Systems Operation/Testing and Adjusting manual for the correct pressure values. If the fuel pressure is low, replace the fuel filters. If the fuel pressure is still low, check the following items: fuel transfer pump, fuel transfer pump coupling and fuel pressure regulating valve.Differential Exhaust Temperature Is Too High
Perform the torque converter stall speed check. Refer to Systems Operation/Testing and Adjusting, "Torque Converter" manual for the power train.Perform the "Cylinder Cutout Test". Analyze the data in order to determine if one of the injectors is misfiring. Refer to Troubleshooting, "Injector Solenoids".Normal intake manifold pressure with a high exhaust temperature can be caused by blockage of the fins of the aftercooler core. Check the aftercooler for correct operation. Check for blockage in the cores of the aftercooler.Aftercooler
Normal intake manifold pressure with a high exhaust temperature can be caused by blockage of the fins of the aftercooler core. Check the aftercooler for correct operation. Check for blockage in the cores of the aftercooler.Valve Adjustment
Ensure that the valve lash and valve bridge adjustment is correct. Refer to Systems Operation/Testing and Adjusting, "Valve Lash Check" and Systems Operation/Testing and Adjusting, "Valve Lash and Valve Bridge Adjustment".Accessory Equipment
Check all flywheel and damper driven equipment for proper operation. Ensure that the accessory equipment is not lugging down the engine.Turbocharger
Check the turbocharger for free operation and for excessive motion in the shaft of the turbocharger.
Examine the turbocharger for potential causes of failure.
If there is any damage to the turbine wheel, examine the exhaust system and the exhaust manifold in order to ensure that no foreign material remains.
If there is any damage to the compressor wheel, examine the air cleaner, the aftercooler, and the ducting in order to ensure that no foreign material remains.
If there is any sign of oil on the compressor side, inspect the accumulator/oil separator and the aftercooler.


Parts screw Force:

F12090
 
F12090 SCREW
H0032H84G, H0033H75C, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H0052C88A, H0054H76D, H0252H77B, H0254H75A, H0351H76K, H0356H75F, H0456B78J, H0456B79K, H0456B80
28636
 
28636 SCREW (1/4-20 X 3/4")
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H040312RD, H0407E92C, H0706A91
F660165
 
F660165 SCREW (LEVER TO ACTUATOR0
H0257F88A, H0257F88B, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0357C88B, H0357F88A, H0357F89C, H0357G90A, H0407E92C, H0504H88C, H0504H88D, H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91
F2217
 
F2217 SCREW, FILL HD. W/LOCKWASHER, 10 - 24 X 3/8
H0407E92C, H0504P89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507Z89B, H0706A91B, H0853F89C, H0853F89E, H0853F89F, H0853F89G, H0856A89A, H0856A89H, H0856L89D, H0856Y89B, H085LD89A, H085LD89
68101
 
68101 SCREW (.375-16 x 1.375)
H0903E91H, H1201A90A, H1501E89A
76213
 
76213 SCREW (1/4-20 X 1-1/8")
H0706A91B, H090312RD, H0903E91H, H1201A90A, H120412RD
Back to top