F521552 Force SCREW, FLYWHEEL


F521552 SCREW, FLYWHEEL Force H0032H84G, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A SCREW
F521552 SCREW, FLYWHEEL Force
Rating:
63

Buy SCREW, FLYWHEEL F521552 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Force entire parts catalog list:

H0032H84G 1984
H0042081C 1981
H0042082D 1982
H0042083E 1983
H0042B78C 1978
H0042B80G 1980
H0042C84L 1984
H0042C87A 1987
H0042H77B 1977
H0042H78D 1978
H0042H78E 1978
H0042H79F 1979
H0043F85A 1985,1986
H005201RS 1995
H005201SD 1996,1997
H005201TS 1997
H005201UD 1998,1999
H0052C88A 1988,1989,1990,1991,1992,1993,1994,1995

Information:


The connection of any electrical equipment and the disconnection of any electrical equipment may cause an explosion hazard which may result in injury or death. Do not connect any electrical equipment or disconnect any electrical equipment in an explosive atmosphere.
Illustration 1 g01131019
Seal for a three-pin connector (typical example)
Table 1
Troubleshooting Test Steps Values Results
1. Check Connectors for Moisture and Corrosion
A. Inspect all the harnesses. Ensure that the routing of the wiring harness allows the wires to enter the face of each connector at a perpendicular angle. Otherwise, the wire will deform the seal bore. This will create a path for the entrance of moisture. Verify that the seals for the wires are sealing correctly.
B. Ensure that the sealing plugs are in place. If any of the plugs are missing, replace the plug. Ensure that the plugs are inserted correctly into the connector.
C. Disconnect the suspect connector and inspect the connector seal. Ensure that the seal is in good condition. If necessary, replace the connector.
D. Thoroughly inspect the connectors for evidence of moisture entry.
Note: It is normal to see some minor seal abrasion on connector seals. Minor seal abrasion will not allow the entry of moisture.
If moisture or corrosion is evident in the connector, the source of the moisture entry must be found and the source of the moisture entry must be repaired. If the source of the moisture entry is not repaired, the fault will recur. Simply drying the connector will not rectify the fault. Check the following items for the possible moisture entry path:
Missing seals
Incorrectly installed seals
Nicks in exposed insulation
Improperly mated connectors
Moisture can also travel to a connector through the inside of a wire. If moisture is found in a connector, thoroughly check the connector harness for damage. Also check other connectors that share the harness for moisture.
Note: The ECM is a sealed unit. If moisture is found in an ECM connector, the ECM is not the source of the moisture. Do not replace the ECM.
Harness, connectors, and seals are OK. Result: A fault has been found with the harness or the connectors.
Repair: Repair the connectors or the wiring, as required. Ensure that all of the seals are correctly installed. Ensure that the connectors have been reattached.
If corrosion is evident on the pins, sockets or the connector, use only denatured alcohol to remove the corrosion. Use a cotton swab or a soft brush to remove the corrosion.
If moisture was found in the connectors, run the engine for several minutes and check again for moisture. If moisture reappears, the moisture is wicking into the connector. Even if the moisture entry path is repaired, it may be necessary to replace the wires.
Use the electronic service tool in order to clear all logged diagnostic codes and then verify that the repair eliminates the fault.
Result: The harness, connectors, and seals are in good condition.
Proceed to Test Step 2.
2. Check the Wires for Damage to the Insulation
A. Carefully inspect each wire for signs of abrasion, nicks, and cuts.
Inspect the wires for the following conditions:
Exposed insulation
Rubbing of a wire against the engine
Rubbing of a wire against a sharp edge
B. Check all of the fasteners for the harness and the strain relief components on the ECM in order to verify that the harness is correctly secured. Also check all of the fasteners in order to verify that the harness is not compressed. Pull back the harness sleeves in order to check for a flattened portion of wire. A fastener that has been overtightened flattens the harness. This damages the wires that are inside the harness.
The wiring is OK
Result: There is damage to the harness.
Repair: Repair the wires or replace the wires, as required.
Use the electronic service tool in order to clear all logged diagnostic codes and then verify that the repair eliminates the fault.
Result: The wires are free of abrasion, nicks, and cuts and the harness is correctly clamped.
Proceed to Test Step 3.
3. Inspect the Connector Terminals
A. Visually inspect each terminal in the connector. Verify that the terminals are not damaged. Verify that the terminals are correctly aligned in the connector and verify that the terminals are correctly located in the connector.
Terminals are aligned and undamaged
Result: The terminals of the connector are damaged.
Repair: Repair the terminals and/or replace the terminals, as required.
Use the electronic service tool in order to clear all logged diagnostic codes and then verify that the repair eliminates the fault.
Result: The terminals are OK.
Proceed to Test Step 4.
Illustration 2 g01802454
A typical example of the lock wedge.
(1) Lock wedge
Table 2
Troubleshooting Test Steps Values Results
4. Perform a Pull Test on Each Wire Terminal Connection
A. Ensure that the locking wedge for the connector is installed correctly. Terminals cannot be retained inside the connector if the locking wedge is not installed correctly.
B. Perform the 30 N (6.7 lb) pull test on each wire. Each terminal and each connector should easily withstand 30 N (6.7 lb) of tension and each wire should remain in the connector body. This test checks whether the wire was correctly crimped in the terminal and whether the terminal was correctly inserted into the connector.
Pull test OK Result: A wire has been pulled from a terminal or a terminal has been pulled from the connector in the 30 N (6.7 lb) pull test.
Repair: Replace the terminal. Replace damaged connectors, as required.
Use the electronic service tool in order to clear all logged diagnostic codes and then verify that the repair eliminates the fault.
Result: All terminals pass the pull test.
Proceed to Test Step 5.
5. Check Individual Pin Retention into the Socket
A. Verify that the sockets provide good retention for the pins. Insert a new pin into each socket one at a time in order to check for a good grip on the pin by the socket.
The sockets provide good retention for the new pin. Result: Terminals are damaged.
Repair: Replace the damaged terminals. Verify that the repair eliminates the problem.
Use the electronic service tool in order to clear all logged diagnostic codes and then verify that the repair eliminates the fault.
Result: The terminals are OK.
Proceed to Test Step


Parts screw Force:

F12090
 
F12090 SCREW
H0032H84G, H0033H75C, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H0052C88A, H0054H76D, H0252H77B, H0254H75A, H0351H76K, H0356H75F, H0456B78J, H0456B79K, H0456B80
F901938-1
 
F901938-1 SCREW, CYLINDER HEAD
H0032H84G, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0054H76D, H0060B76A, H0060B78B, H0060H79C, H0060H80
F10071
 
F10071 SCREW
H0032H84G, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81
69022
 
69022 SCREW (10-32 X 1/2")
H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS, H025201U
F175634
 
F175634 SCREW-CONN ROD (STEEL ROD ONLY)
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A
28636
 
28636 SCREW (1/4-20 X 3/4")
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H040312RD, H0407E92C, H0706A91
824678
 
824678 SCREW, FRICTION
H005201SD, H005201TS, H005201UD, H0052C88A
34939
 
34939 SCREW (1/4-20 X 1/2")
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0407E92C, H0706A91B, H0903E91H, H1201A90A, H1501E89A
Back to top