F525064 Force SCREW - C-D COIL


F525064 SCREW - C-D COIL Force H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0064H80F, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H79B, H0072H80C, H0072H82E, H0075H79A, H0082H78J, H0504H88C, H0507C87C, H0507C88B, H0507F88A, H120LD90 SCREW
F525064 SCREW - C-D COIL Force
Rating:
78

Buy SCREW - C-D COIL F525064 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 19
 

Force entire parts catalog list:

H0060B78B 1978
H0060H79C 1979
H0060H80D 1980
H0062B78J 1978
H0062H79K 1979
H0064H80F 1980
H0067H79C 1979
H0070B79A 1979
H0071H81B 1981
H0071H82C 1982
H0071H83D 1983
H0071H84E 1984,1985
H0072B81D 1981
H0072H79B 1979
H0072H80C 1980
H0072H82E 1982
H0075H79A 1979
H0082H78J 1978
H0504H88C 1988
H0507C87C 1987
H0507C88B 1988
H0507F88A 1988
H120LD90A 1990
H120LD90B 1990
H120LD90C 1990
H120LD91B 1991
H125LD89A 1989
H125LD89B 1989

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     5P-0332     Crowfoot Wrench     1    Start By:
Remove the fuel pressure relief valve, if necessary. Refer to Disassembly and Assembly, "Relief Valve (Fuel) - Remove and Install".
Remove the fuel lines. Refer to Disassembly and Assembly, "Fuel Lines - Remove and Install".
Contact with high pressure fuel may cause personal injury or death. Wait 60 seconds after the engine has stopped to allow fuel pressure to purge before any service or repair is performed on the engine fuel lines.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Fuel injection lines MUST only be used once. Discard all fuel injection lines after use.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Illustration 1 g01360608
Note: Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Disconnect harness assembly (1) .Note: A new fuel rail includes the fuel pressure sensor, the adapter, and the fuel pressure relief valve.
Fuel pressure sensor (2) must only be used once. Discard fuel pressure sensor (2) after use.
Use Tooling (A) in order to remove fuel pressure sensor (2) , if necessary. Discard fuel pressure sensor (2) if the sensor is removed.
Remove adapter (3) , if necessary.
Remove tube assembly (4) from fuel rail (5) .
Remove studs (6) and remove fuel rail (5) .Installation Procedure
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     5P-0332     Crowfoot Wrench     1    
B     161-9203     Grease Cartridge     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Fuel injection lines MUST only be used once. Discard all fuel injection lines after use.
Illustration 2 g01360608
Position fuel rail (5) and install studs (6) . Tighten studs (6) to a torque of 28 7 N m (21 5 lb ft).
Install new tube assembly (4) on fuel rail (5) . Install the fuel lines. Refer to Disassembly and Assembly, "Fuel Lines - Remove and Install".
Apply Tooling (B) to the threads and face of adapter (3) .Note: A new fuel rail includes the fuel pressure sensor, the adapter, and the fuel pressure relief valve.
Install adapter (3) , if necessary. Tighten adapter (3) to a torque of 95 3 N m (70 2 lb ft).
Use Tooling (A) in order to install new fuel pressure sensor (2) , if necessary. Tighten fuel pressure sensor (2) to a torque of 35 3 N m (26 2 lb ft).
Connect harness assembly (1) .End By: Install the fuel pressure relief valve, if necessary. Refer to Disassembly and Assembly, "Relief Valve (Fuel) - Remove and Install".


Parts screw Force:

F438165
 
F438165 SCREW, FUEL BOWL
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0357C86A, H0357C87A, H0357C88
F458519
 
F458519 SCREW, TILLER IDLE STOP FOR MANUAL START MODELS
H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H79B, H0072H80C, H0072H82E, H0082H78J, H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78
F901938-1
 
F901938-1 SCREW, CYLINDER HEAD
H0032H84G, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0054H76D, H0060B76A, H0060B78B, H0060H79C, H0060H80
F10275
 
F10275 SCREW-SEALING
H0091H84D, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS, H025201US, H040312RD, H040312SD, H0407E92C, H0507A90C, H0507A90
F10328
 
F10328 SCREW (9.9)
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015211SS, H0152C84K, H0152S89A, H0352F90C, H0353E91A, H0353E91B, H040312RD, H040312SD, H040312UD, H0407E92
F2200
 
F2200 SCREW, #2 - 24 X 1 HEX HD.
H0504H88C, H0504H88D, H0504P89B, H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507C87C, H0507C88B, H0507E91B, H0507F88A, H0507Z89B, H0853F89C, H0853F89E, H0853F89F, H0853F89G, H0856A89
817504
SCREW (.250-20 x 1.500)
817504 SCREW (.250-20 x 1.500)
H040312RD, H0407E92C, H0706A91B, H090312RD, H0903E91D, H0903E91H, H090LD90B, H090LD91D, H1201A90A, H120412RD, H120LD91B, H120LD91D, H120LD92B, H1501E89A
817458
 
817458 SCREW (#10-24 x 2.250)
H040312RD, H0407E92C, H0706A91B, H090312RD, H0903E91D, H0903E91H, H090LD90B, H090LD91D, H1201A90A, H120412RD, H120LD91B, H120LD91D, H120LD92B, H1501E89A
Back to top