821756 Force SEAL, DRIVESHAFT


821756 SEAL, DRIVESHAFT Force H040312RD SEAL
821756 SEAL, DRIVESHAFT Force
Rating:
28

Buy SEAL, DRIVESHAFT 821756 Force genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$201.41
 

17-07-2024
7.0[3.15] Pounds
US: WunderCarParts
Koni Classic Shocks 821756
Koni Part Number 821756 || One Shock Absorber || Rebound adjustable (off the vehicle), provides fine tuning ability of ride characteristics || KONI's Warranty protects the original purchaser against defects in materials and workmanship, excluding mounting hardware and bushings, when used under normal operating conditions.
$197.98
 

17-07-2024
5.0[2.25] Pounds
US: Jinnspeed
Koni KD 821756 Damper Part Performance
Koni Koni shock absorber Porsche 911 behind Koni OE & # x202 F; 911.333.051.11 + 13 || Premium 100% perfect fit brand product, || Improvement of motor skills
Number on catalog scheme: 2
 

Compatible models:

H040312RD   Force

Force entire parts catalog list:

H040312RD 1995

Information:


Table 1
Diagnostic Trouble Codes
J1939 Code CDL Code Code Description Comments
4215-3 267-3 Remote Shutdown Input : Voltage Above Normal If both contacts from the ground level shutdown switch change to the same state and the engine is running, the engine will continue to run. The code is logged.
4215-4 267-4 Remote Shutdown Input : Voltage Below Normal If both contacts from the ground level shutdown switch change to the same state and the engine is running, the engine will continue to run. The code is logged.
4215-31 E678 (1) Ground Level Shutdown The inputs from the ground level shutdown switch to the ECM have changed states.
The engine will shut down. The code is logged.
4215-31 E678 (2) Ground Level Shutdown The inputs from the ground level shutdown switch to the ECM have changed states.
The engine will shut down. The code is logged.
4215-31 E678 (3) Ground Level Shutdown The inputs from the ground level shutdown switch to the ECM have changed states.
The engine will shut down. The code is logged. The shutdown switch will shut down the engine. The engine ECM remains active. Caterpillar Electronic Technician (ET) can be used to communicate with the ECM. The shutdown switch must be returned to the RUN position before the ECM will allow the engine to start.The ECM reads the position of the shutdown switch. If the engine is running, the ECM disables the fuel injection. The status screen will display"Injection Disabled" and "Remote Shutdown".
Illustration 1 g03018516
Schematic
Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Determine the Diagnostic Code
A. Establish communication between Cat® ET and the ECM . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Observe the "Active Diagnostic" screen on Cat ET. Wait at least 30 seconds so that any codes may become active.
C. Look for these codes:
E678 or 4215-31
267-3 or 4215-3
267-4 or 4215-4
Diagnostic Trouble Codes
Result: A E678 or 4215-31 diagnostic code is active.
Proceed to Test Step 2.
Result: A 267-3 or 4215-3 diagnostic code is active.
Proceed to Test Step 3.
Result: A 267-4 or 4215-4 diagnostic code is active.
Proceed to Test Step 4.
2. Check the Status of the Shutdown Switch on Cat ET
A. Activate the shutdown.
B. Use Cat ET to verify that the engine rpm is 0. Return the shutdown switch to the RUN position.
C. Use Cat ET to observe the status of the shutdown switch.
Switch Status
Result: The status of the shutdown switch changed states after returning the shutdown switch to the RUN position.
The shutdown switch is operating correctly.
Result: The status of the shutdown switch does not change states after returning the shutdown switch to the RUN position.
Proceed to Test Step 3.
3. Create a Short at the Connector for the Shutdown Switch
A. Turn the keyswitch to the OFF position.
B. Disconnect the connector for the shutdown switch.
C. Create a short circuit at the connector for the shutdown switch between terminal 1 and terminal 2.
D. Turn the keyswitch to the ON position.
E. Use Cat ET to observe the status of the shutdown switch.
F. Remove the wire short.
Short Circuit
Result: The status of the shutdown switch changed states after creating the short circuit.
Repair: Install a new shutdown switch.
Verify that the problem is resolved.
Result:The status of the shutdown switch did not change states after creating the short circuit.
Repair: Repair the wiring or replace the harness.
Use Cat ET to verify that the problem is resolved.
4. Create an Open at the Connector for the Shutdown Switch
A. Turn the keyswitch to the OFF position.
B. Disconnect the connector for the shutdown switch.
C. Turn the keyswitch to the ON position.
D. Use Cat ET to observe the status of the shutdown switch.
Open Circuit Detected
Result: The status of the shutdown switch changed states after creating the open circuit.
Repair: Install a new shutdown switch.
Use Cat ET to verify that the problem is resolved.
Result: The status of the shutdown switch did not change states after creating the open circuit.
Repair: Repair the harness or replace the harness.
Use Cat ET to verify that the problem is resolved.


Parts seal Force:

F474146
 
F474146 SEAL, CRANKSHAFT
H040312RD, H0407E92C, H0504H88C, H0504H88D, H0504P89B, H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507C87C, H0507C88B, H0507E91B, H0507F88A, H0507Z89B, H0558H79L, H0559B80M, H0559H77
42941
 
42941 SEAL, Water Tube
H040312RD, H040312SD, H040312UD, H0706A91B, H075312SD, H075312UD
819394
 
819394 SEAL, CRANKSHAFT LOWER
H040312RD, H040312SD, H040312UD, H0407E92C
820355
SEAL, CABLE ENTRY
820355 SEAL, CABLE ENTRY
H040312RD, H040312SD, H040312UD
19624A 1
 
19624A 1 SEAL KIT
H040312RD, H040312SD, H040312UD
821510
 
821510 SEAL, BOTTOM COWL
H040312RD, H040312SD, H040312UD
824942 2
822404
 
822404 SEAL
H040312RD, H040312SD, H040312UD
Back to top