F269122-1 Force CRANKCASE PARTING LINE SEAL (NOT SHOWN)


F269122-1 CRANKCASE PARTING LINE SEAL (NOT SHOWN) Force H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0357H83N, H0456B78J, H0456B79 CRANKCASE
F269122-1 CRANKCASE PARTING LINE SEAL (NOT SHOWN) Force
Rating:
43

Buy CRANKCASE PARTING LINE SEAL (NOT SHOWN) F269122-1 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

Force entire parts catalog list:

H0202B80L 1980
H0202B81M 1981
H0202H79K 1979
H0202H82N 1982
H0252B83G 1983,1984
H0252H77B 1977
H0252H78C 1978
H0252H78D 1978
H0254H75A 1975,1976
H0306B80C 1980
H0307H81D 1981
H0350H78L 1978
H0351H76K 1976
H0352H77H 1977,1978
H0352H79L 1979
H0353H78K 1978
H0353H80M 1980
H0353H81N 1981
H0353H82P 1982
H0356H75F 1975,1976,1977
H0357H83N 1983,1984
H0456B78J 1978
H0456B79K 1979
H0456B80L 1980,1981
H0457H82N 1982
H0457H83P 1983,1984
H0503B83A 1983
H0507H81A 1981
H0507H82B 1982
H0555H74G 1974,1976
H0558H79L 1979
H0559B80M 1980
H0559H77H 1977
H0559H77J 1977
H0559H78K 1978
H0559H80N 1980,1981
H0559H83R 1983
H0606H84A 1984,1985,1989
H0659B78B 1978

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     4C-5597     Anti-Seize Compound     -    
B     195-4609     Seal Pick     1    
C     -     Isopropyl Alcohol     -    
D     5P-4996     Plug     2    
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Illustration 1 g02300314
Remove sheet assembly (1) .
Illustration 2 g02300333
Illustration 3 g02300500
Remove tube assemblies (2) and tube assembly (7). Plug the coolant lines with Tooling (D) .
Disconnect cable assembly (4) and remove spark plug (3) .
Remove flame detection sensor (8) and disconnect heated nozzle (9) .
Remove nuts (5), combustion head (6), gasket (13), tube assembly (12), and gasket (11) .Note: Gaskets are one time use. Install new gaskets upon installation.
If required, remove studs (10) .
Illustration 4 g02482996
Use Tooling (B) in order to remove O-ring seals (14) and (15) from the heated nozzle (9). Discard the O-ring seals.Installation Procedure
Install combustion head (6) in the reverse order of removal.
Apply Tooling (A) onto the threads of studs (10). Tighten studs (10) to a torque of 17 2 N m (150 18 lb in).
Apply Tooling (A) onto the threads of the studs and nuts (5). Tighten nuts (5) in a crisscross pattern to a torque of 23 3 N m (204 27 lb in). Tighten nuts (5) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft). Tighten nuts (5) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft).
Use caution when you are using isopropyl alcohol. Avoid prolonged skin contact with isopropyl alcohol.Vapors may be harmful if inhaled. Use only in a well ventilated area. Do not smoke while using isopropyl alcohol.Isopropyl alcohol is flammable. Do not use near an open flame or near welding operations. Keep isopropyl alcohol away from heated surfaces exceeding 482°C (900°F).
Note: This connection is an electrical connection and cannot be lubricated with a petroleum-based lubricant. Isopropyl alcohol is the only approved lubrication for this connection.
Lubricate new O-ring seals (14) and (15) with Tooling (C) prior to installation.
Apply Tooling (A) to the threads of flame detection temperature sensor (8) and install the sensor. Tighten flame detection temperature sensor (8) to a torque of 45 5 N m (33 3 lb ft).
Tighten spark plug (3) to a torque of 47 4 N m (35 3 lb ft).
Check the coolant level. If necessary, refer to Operation and Maintenance Manual, "Coolant - Change" for the proper filling procedures.
Perform the ARD ignition test. Refer to Troubleshooting Manual, "ARD Ignition - Test".


Back to top