F286914 1 Force SLEEVE-WATER LINE


F286914 1 SLEEVE-WATER LINE Force H0091H84D, H009201RS, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS, H025201US SLEEVE
F286914 1 SLEEVE-WATER LINE Force
Rating:
13

Buy SLEEVE-WATER LINE F286914 1 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 40
 

Force entire parts catalog list:

Information:


Illustration 1 g03041356
Table 1
Specification for 211-3218 Piston and 256-9837 Piston
Item Qty Part Specification Description
Thoroughly lubricate the ring grooves of the entire piston with the clean engine oil before installation of the piston rings. After assembly, completely lubricate the mating surfaces of the rings to the cylinder liner with the clean engine oil.
1 1 262-3066 Piston Ring Install the piston ring with the "Up-1" side toward the top of the piston. The top piston ring must be installed with the red colored stripe to the right of the ring end gap.
Width of groove in new piston for the top piston ring is 3.600 0.010 mm (0.1417 0.0004 inch).
Clearance between the groove and the new piston ring is 0.130 to 0.190 mm (0.0051 to 0.0075 inch).
When the piston ring is installed in a cylinder liner with a bore size of 170 mm (6.7 inch), the clearance between the ends of the piston ring is 0.575 0.125 mm (0.0226 0.0049 inch).
The increase in the clearance between the ends of the piston ring for each 0.03 mm (0.001 inch) increase in the cylinder liner bore size is 0.08 mm (0.003 inch).
Thickness of the new top piston ring is 3.45 to 3.49 mm (0.136 to 0.137 inch).
2 1 8N-1234 Ring Install the piston ring with the "Up-2" side toward the top of the piston. The intermediate piston ring must be installed with the green colored stripe to the right of the ring end gap.
When the piston ring is installed in a cylinder liner with a bore size of 170 mm (6.7 inch), the clearance between the ends of the piston ring is 0.80 0.20 mm (0.031 0.008 inch).
The increase in the clearance between the ends of the piston ring for each 0.03 mm (0.001 inch) increase in the cylinder liner bore size is 0.08 mm (0.003 inch).
Thickness of the new intermediate piston ring is 3.470 0.020 mm (0.1366 0.0008 inch).
Width of groove in new piston for intermediate piston ring is 3.600 0.010 mm (0.1417 0.0004 inch).
Clearance between the groove and the new intermediate piston ring is 0.100 to 0.160 mm (0.0039 to 0.0063 inch).
3 1 7W-2221 Ring The spring ends of the oil control piston ring should be assembled 180 degrees from the ring end gap. The white-colored portion of the piston ring must be visible at the ring end gap.
Thickness of new oil piston ring is 4.954 0.019 mm (0.1950 0.0007 inch).
Clearance between groove and new oil piston ring is 0.067 to 0.125 mm (0.0026 to 0.0049 inch).
When the piston ring is installed in a cylinder liner with a bore size of 170 mm (6.7 inch), the clearance between the ends of the piston ring is 0.70 0.19 mm (0.028 0.007 inch).
The increase in the clearance between the ends of the piston ring for each 0.03 mm (0.001 inch) increase in the cylinder liner bore size is 0.08 mm (0.003 inch).
Width of groove in piston for the new oil piston ring is 5.050 0.010 mm (0.1988 0.0004 inch).
After all piston rings have been installed, rotate the piston rings, so that the end gaps are 120 degrees from each other.
4 - - Bore diameter for piston pin is 70.38 0.10 mm (2.771 0.004 inch).
5 1 138-8506 Piston Pin Before assembly, completely lubricate the piston pin, the piston pin bore, the connecting rod eye, and the connecting rod pin bearing with clean engine oil.
Diameter is 69.962 0.005 mm (2.7544 0.0002 inch).
Length of piston pin is 137.60 0.13 mm (5.417 0.005 inch).
6 2 8N-7296 Pin Retainer Assemble the pin retainer with the gap towards the top of the piston.
Thickness of the new retainer ring is 2.40 0.08 mm (0.094 0.003 inch).
Width of groove in the new piston for the retainer ring is 2.75 0.15 mm (0.108 0.006 inch).


Parts sleeve Force:

F458695
 
F458695 SLEEVE, STEERING HANDLE GRIP FOR MANUAL START MODELS
H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0062H79M, H0067H79C, H0070B79A, H0072H79B, H0072H80C, H0082H76G, H0082H78J, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H009201RS, H0092284D, H0092B80G, H0092H79F, H0092H84
F12141
 
F12141 SLEEVE, HIGH TENSION LEAD
H0060B76A, H0062H79M, H0064H78D, H0064H82H, H0082H76G, H0082H79K, H0091H84D, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0102H76C, H0102H78E, H0122H79E, H0152B78D, H0152B83
F286914
 
F286914 SLEEVE WATER LINE
H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0094H81F, H0095B80F, H0095B81G, H0095H82H, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0125H79E, H0152B78D, H0152B83J, H0152C84
F681188
 
F681188 SLEEVE (91A/92B & SER. # E000001 THRU E034999)
H005201RS, H005201SD, H005201TS, H0052C88A, H0091H84D, H009201RS, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS, H0352F90B, H0352F90C, H0353E91A, H0353E91
828406
SLEEVE-STEERING HANDLE GRIP
828406 SLEEVE-STEERING HANDLE GRIP
H009201SD, H009201UD, H009201US, H0092S88A, H015201US, H015211SS, H025201RD, H025201TD, H025201TS, H025201US
286914
SLEEVE, WATER IINE
286914 SLEEVE, WATER IINE
H0092S91A, H0093S91A
458695
SLEEVE
458695 SLEEVE
H0092S91A, H0093S91A
286914 1
Back to top