F458695 Force SLEEVE, STEERING HANDLE GRIP FOR MANUAL START MODELS


F458695 SLEEVE, STEERING HANDLE GRIP FOR MANUAL START MODELS Force H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0062H79M, H0067H79C, H0070B79A, H0072H79B, H0072H80C, H0082H76G, H0082H78J, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H009201RS, H0092284D, H0092B80G, H0092H79F, H0092H84 SLEEVE
F458695 SLEEVE, STEERING HANDLE GRIP FOR MANUAL START MODELS Force
Rating:
98

Buy SLEEVE, STEERING HANDLE GRIP FOR MANUAL START MODELS F458695 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 83
 

Force entire parts catalog list:

H0060B76A 1976
H0060B78B 1978
H0060H79C 1979
H0060H80D 1980
H0062B78J 1978
H0062H79K 1979
H0062H79M 1979
H0067H79C 1979
H0070B79A 1979
H0072H79B 1979
H0072H80C 1980
H0082H76G 1976,1977
H0082H78J 1978
H0082H79K 1979
H0091B80B 1980
H0091H79A 1979
H0091H83C 1983
H0091H84D 1984
H009201RS 1995
H0092284D 1984,1985,1986,1987,1988,1989,1990,1991,1992,1993,1994,1995
H0092B80G 1980
H0092H79F 1979
H0092H84L 1984
H0092S88A 1988
H0092S91A 1991
H0093S91A 1991
H0094H81F 1981,1982
H0101B78A 1978
H0102H76C 1976,1977
H0102H78E 1978
H0121B79A 1979
H0122H79E 1979
H015201RS 1995
H0152B78D 1978
H0152B83J 1983,1984
H0152C84K 1984
H0152H79E 1979
H0152H80F 1980
H0152H81G 1981
H0152S89A 1989
H0202B80L 1980
H0202B81M 1981
H0202H79K 1979
H0202H82N 1982
H0252B83G 1983,1984
H0252H77B 1977
H0252H78C 1978
H0252H78D 1978
H0254H75A 1975,1976
H0352F90B 1990
H0352F90C 1990
H0352H77H 1977,1978
H0352H79L 1979
H0353E91A 1991
H0353E91B 1991
H0353H78K 1978
H0353H80M 1980
H0353H81N 1981
H0353H82P 1982
H0357F89C 1989
H0357G90A 1990
H0503B83A 1983

Information:


Table 1
J1939 Code and Description CDL Code and Description System Response
5562-1
Supplemental Fan Speed : Low - most severe (3) E1190 (3)
Supplemental Fan Speed : Low - most severe (3) The code is logged if the fan speed is not within 300 rpm of the commanded speed. On Motor Grader Applications, the code will be logged if communication for the CAN data link is lost between the Electronic Control Module (ECM) and the fan.
N/A 3548-8
Aftertreatment Cooling Fan Control Module : Abnormal Frequency, Pulse Width, or Period The code is logged if the fan speed is not within 300 rpm of the commanded speed.
N/A 3548-11
Aftertreatment Cooling Fan Control Module : Other Failure Mode The aftertreatment cooling fan is receiving low supply voltage or has failed internally.
N/A E1352 (3)
High Aftertreatment Cooling Fan Temperature The internal temperature of the aftertreatment cooling fan exceeded the maximum allowable temperature/threshold. The fan is NOT failed.
N/A 3548-5
Aftertreatment Cooling Fan Control Module : Current Below Normal The ECM has detected an open circuit on the aftertreatment cooling fan circuit.
N/A 3548-6
Aftertreatment Cooling Fan Control Module : Current Above Normal The ECM has detected a short circuit on the aftertreatment cooling fan circuit. Note: The E1352 (3) code indicates that the aftertreatment cooling fan internal temperature has exceeded the maximum threshold. The fan will shut down, and the machine should be shut down as soon as possible to avoid damage. The aftertreatment cooling fan is not failed.Note: The following schematic is used for Motor Grader Applications
Illustration 1 g03684589
Motor Grader Applications
Note: The following schematic is used for Articulated Truck Applications
Illustration 2 g06073472
Articulated Truck Applications
Table 2
Troubleshooting Test Steps Values Results
1. Determine the Machine
Note: The aftertreatment cooling fan is equipped only on Articulated Truck and Motor Grader applications.
Machine Application
Result: The machine is an Articulated Truck.
Proceed to Test Step 2.
Result: The machine is a Motor Grader.
Proceed to Test Step 5.
2. Inspect the Fan
A. Inspect the fan for the following conditions:
- Damaged fan blades
- Debris against the fan blades
- Air flow is obstructed
Fan
Result: The fan is OK.
Proceed to Test Step 3.
Result: The fan is obstructed.
Repair: Remove the obstruction. Verify that the problem is resolved. Return to service.
Result: The fan is damaged.
Repair: Replace the fan. Verify that the problem is resolved.
Return to service.
3. Check for Voltage at the Fan
A. Turn the keyswitch to ON.
B. Start Engine
C. Connect Cat® Electronic Technician (ET).
D. Perform an "ARD Ignition Test".
E. Measure the voltage between the Battery+ and Battery- on the Aftertreatment Cooling Fan connector.
Battery Voltage
Result: The voltage is OK.
Proceed to Test Step 4.
Result: The voltage is NOT OK.
Repair: The problem is in the wiring between the fan and the battery. Check the power supply and ground to the VLPM, and the aftertreatment cooling fan relay. Repair the wiring.
Verify that the problem is resolved. If the problem is not resolved. Return to service.
4. Check for Continuity Between the Fan and the ECM
A. Turn the keyswitch to OFF.
B. Disconnect the 3-pin connector from the aftertreatment cooling fan.
C. Disconnect the J1 connector from the engine ECM.
D. Check for continuity between the following pins:
- Pin 3 (PWN In) on the 3-pin aftertreatment cooling fan connector and pin 31 on the J1 ECM connector.
- Pin A (Speed Feedback) on the 3-pin aftertreatment cooling fan connector and pin 1 on the J1 ECM connector.
Continuity
Result: There are less than 10 ohms of resistance on each wire.
Repair: Replace the aftertreatment cooling fan. Verify that the problem is resolved.
Result: There are more than 10 ohms of resistance on each wire.
Repair: Repair the wiring or replace the wiring. Verify that the problem is resolved.
Return to service.
5.Check for Fault Codes
A. Turn the keyswitch to ON.
B. Connect Cat ET.
C. Record the fault codes.
Codes
Result: An E1190 (3) or a 3548-8 is present.
Proceed to Test step 6.
Result: A 3548-5 or a 3548-6 is present.
Proceed to Test Step 10.
Result:A 3548-11 is present.
Proceed to Test Step 11.
Result: An E1352 (3) is present.
Proceed to Test Step 15.
6. Inspect the Fan
A. Inspect the fan for the following conditions:
- Damaged fan blades
- Debris against the fan blades
- Air flow is obstructed
Fan
Result: The fan is OK.
Proceed to Test Step 7.
Result: The fan is obstructed.
Repair: Remove the obstruction. Verify that the problem is resolved.
Result: The fan is damaged.
Repair: Replace the fan. Verify that the problem is resolved.
Return to service.
7. Check for Voltage at the Fan
A. Disconnect the two-pin connector to the fan.
B. Measure the voltage between pins 1 and 2 on the connector.
Battery Voltage
Result: The voltage is equal to battery voltage.
Proceed to Test Step 8.
Result: The voltage is not equal to battery voltage.
Repair: The problem is in the wiring between the fan and the battery. Check the fuse between the fan and the battery. Repair the wiring.
Return to service.
8. Check for Continuity Between the Fan and the ECM
A. Turn the keyswitch to OFF.
B. Disconnect the four-pin connector on the aftertreatment cooling fan.
C. Disconnect both the J1 and the J2 harness connectors from the engine ECM.
D. Check for continuity between the following pins:
- Pin 1 on the 4-pin aftertreatment cooling fan connector and pin 20 on the J1 ECM connector.
- Pin 3 on the 4-pin aftertreatment cooling fan connector and pin 12 on the J1 ECM connector.
- Pin 4 on the 4-pin aftertreatment cooling fan connector and pin 11 on the J2 ECM connector.
Continuity
Result: There are


Parts sleeve Force:

F94914
 
F94914 SLEEVE
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0507H81A, H0507H82B, H0555H74G
F15116
SLEEVE
F15116 SLEEVE
H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503B83A, H0507H81A, H0507H82B, H0555H74G
F15108
 
F15108 SLEEVE
H0202B81M, H0202H79K, H0252B83G, H0252H77B, H0252H78D, H0254H75A, H0306B80C, H0307H81D, H0357H83N
F12141
 
F12141 SLEEVE, HIGH TENSION LEAD
H0060B76A, H0062H79M, H0064H78D, H0064H82H, H0082H76G, H0082H79K, H0091H84D, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0102H76C, H0102H78E, H0122H79E, H0152B78D, H0152B83
F286914
 
F286914 SLEEVE WATER LINE
H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0094H81F, H0095B80F, H0095B81G, H0095H82H, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0125H79E, H0152B78D, H0152B83J, H0152C84
F681188
 
F681188 SLEEVE (91A/92B & SER. # E000001 THRU E034999)
H005201RS, H005201SD, H005201TS, H0052C88A, H0091H84D, H009201RS, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS, H0352F90B, H0352F90C, H0353E91A, H0353E91
F286914 1
 
F286914 1 SLEEVE-WATER LINE
H0091H84D, H009201RS, H009201SD, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS, H025201US
Back to top