F2119 Force SPACER BEVEL GEAR REAR

Table 1
Diagnostic Codes for the Active Analog Sensors
J1939 Code CDL Code Code Description
(Code descriptions may vary) Comments
107-3 582-3 Engine Air Filter 1 Differential Pressure : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
107-4 582-4 Engine Air Filter 1 Differential Pressure : Voltage Above Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
1176-3 2738-3 Turbocharger #1 Compressor Inlet Pressure Sensor : Voltage Above Normal The ECM detects the following conditions:
The signal voltage for the low-pressure turbocharger compressor inlet pressure sensor is more than 4.8 VDC.
The ECM has been powered for at least 0.24 seconds.
The ECM will log the diagnostic code.
1176-4 2738-4 Turbocharger #1 Compressor Inlet Pressure Sensor : Voltage Below Normal The ECM detects the following conditions:
The signal voltage for the low-pressure turbocharger compressor inlet pressure sensor is less than 0.2 VDC.
The ECM has been powered for at least 0.24 seconds.
The ECM will log the diagnostic code.
1381–3 2247–3 Engine Fuel Supply Pump Inlet Pressure : Voltage Above Normal The ECM detects a signal voltage that is not in the acceptable range.
1381–4 2247–4 Engine Fuel Supply Pump Inlet Pressure : Voltage Below Normal The ECM detects a signal voltage that is not in the acceptable range.
5578–3 289–3 Engine Fuel Delivery Absolute Pressure : Voltage Above Normal The ECM detects a signal voltage that is not in the acceptable range.
5578–4 289–4 Engine Fuel Delivery Absolute Pressure : Voltage Below Normal The ECM detects a signal voltage that is not in the acceptable range.
5580–3 460–3 Engine Filtered Fuel Delivery Absolute Pressure : Voltage Above Normal The ECM detects a signal voltage that is not in the acceptable range.
5580–4 460–4 Engine Filtered Fuel Delivery Absolute Pressure : Voltage Below Normal The ECM detects a signal voltage that is not in the acceptable range.
Follow the troubleshooting procedure to identify the root cause of the fault.
For 107 (582) diagnostic codes, refer to the schematic shown in Illustration 1. For all other diagnostic codes, refer to the application schematic.
Illustration 1 g06308612
Schematic for the sensors on the J1 ECM connector
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P1/J1 ECM connectors and the engine pressure sensors.
Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the sensor connectors that are associated with the active diagnostic code.
C. Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
D. Check the harness for corrosion, abrasion, and pinch points from the engine pressure sensors to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check For Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Wait at least 10 seconds for activation of the diagnostic codes.
D. Verify if any of the diagnostic codes that are listed in Table 1 are active.
E. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: There are no active diagnostic codes for the active sensors.
If there are logged diagnostic codes for the active sensors, the fault may be intermittent.
Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" to identify intermittent faults.
Result: A diagnostic code is active for one or more of the active sensors.
Proceed to Test Step 3.
3. Check the Supply Voltage at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the connector for the suspect sensor.
C. Turn the keyswitch to the ON position. Do not start the engine.
D. Measure the voltage between the sensor supply terminal and the ground terminal on the harness connector for the suspect sensor.
E. Turn the keyswitch to the OFF position.
F. Reconnect the sensor.
4.8 VDC to 5.2 VDC
Result: The voltage measurement is not within the expected range. The fault is in the supply wire or the ground wire in the engine wiring harness.
Repair: Repair the faulty wiring or replace the faulty wiring.
Use the electronic service tool to clear all logged diagnostic codes. Return the engine to service.
Result: The voltage measurement is within the expected range. The correct supply voltage is reaching the sensor.
Proceed to Test Step 4.
4. Check the Type of Diagnostic Code that is Active
A. Turn the keyswitch to the ON position. Wait at least 10 seconds for activation of the diagnostic codes.
B. Use the electronic service tool to check for active diagnostic codes. Record all active diagnostic codes.
Diagnostic codes
Result: A -4 diagnostic code is active for one or more of the active sensors.
Proceed to Test Step 5.
Result: A -3 diagnostic code is active for one or more of the active sensors.
Proceed to Test Step 7.
5. Create An Open Circuit at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the connector for the sensor with the -4 diagnostic code.
C. Turn the keyswitch to the ON position. Wait for at least 10 seconds for activation of the diagnostic codes.
D. Use the electronic service tool to check the "Active Diagnostic Code" screen. Check for a -3 diagnostic code.
Diagnostic codes
Result: A -4 diagnostic code was active before disconnecting the sensor. A -3 diagnostic code became active after disconnecting the sensor - the sensor is faulty.
Repair: Temporarily connect a new sensor to the harness, but do not install the new sensor in the engine. Use the electronic service tool to verify that the repair eliminates the fault and then