F12346 Force STATOR PLATE W/LAMINATIONS


F12346 STATOR PLATE W/LAMINATIONS Force H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0350H78L, H0351H76K STATOR
F12346 STATOR PLATE W/LAMINATIONS Force
Rating:
98

Buy STATOR PLATE W/LAMINATIONS F12346 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

Force entire parts catalog list:

H0202B80L 1980
H0202B81M 1981
H0202H79K 1979
H0202H82N 1982
H0252B83G 1983,1984
H0252H77B 1977
H0252H78C 1978
H0252H78D 1978
H0254H75A 1975,1976
H0350H78L 1978
H0351H76K 1976

Information:

Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque Values.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
Note: If all connecting rod bearings require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that both pairs of the connecting rod bearings are installed before changing from one pair of cylinders to another pair of cylinders. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Install" for the correct procedure.
Illustration 1 g02798265
Remove bolt (2), the O-ring seal, and oil pump screen (1).
Illustration 2 g02798267
The connecting rod and the connecting rod cap should have an etched Number (X) on the side. The number on the connecting rod and the connecting rod cap must match. If necessary, make a temporary mark on the connecting rod and connecting rod cap (4) in order to identify the cylinder number.
Remove bolts (3). Remove connecting rod cap (4) from the connecting rod.
Illustration 3 g02798268
Carefully push connecting rod (5) into the cylinder bore until connecting rod (5) is clear of the crankshaft. Remove lower bearing shell (7) and then remove upper bearing shell (6) from connecting rod (5). Keep the bearing shells together.
Repeat Step 3 through Step 4 for the remaining bearing shells.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
Ensure that the bearing shells are clean and free from wear and damage. If necessary, replace the bearing shells.
Illustration 4 g02798268
Illustration 5 g02798267Note: Connecting rods and bearing are marked with color codes. The color codes are blue and unmarked. The bearings must match up with the corresponding connecting rods. It is possible to have different color codes in the same engine.
Install upper bearing shell (6) into connecting rod (5). Ensure that the locating tab for the upper bearing shell is correctly seated in the slot in connecting rod (5). Note: The ends of the upper bearing shell must be centered in the connecting rod. The ends of the upper bearing shell are to be positioned equally in relation to the mating faces of the connecting rod.
Lubricate upper bearing shell (6) with clean engine oil.
Carefully pull connecting rod (5) against the crankshaft.
Clean connecting rod cap (4). Install lower bearing shell (7) into connecting rod cap (4). Ensure that the locating tab for lower bearing shell (7) is correctly seated in the slot in connecting rod cap (4).
Lubricate the crankshaft and lubricate lower bearing shell (7) with clean engine oil.
Install connecting rod cap (4) to the connecting rod.Note: Ensure that etched Number on connecting rod cap (4) matches etched Number on the connecting rod. Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.
For the C3.3B install new bolts (3) to the connecting rod. Apply clean engine oil to the threads of bolts. Tighten the bolts evenly to a torque of 69 to 73 N m (51 to 54 lb ft).
For the C2.6 install new bolts (3) to the connecting rod. Apply clean engine oil to the threads of bolts. Tighten the bolts evenly to a torque of 45 to 49 N m (33 to 36 lb ft).
Illustration 6 g02798265
Position engine oil screen (1) and install the O-ring seal and bolt (2).
Repeat Step 2 through Step 8 for the remaining connecting rod bearings.Note: If all connecting rod bearings require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that both pairs of the connecting rod bearings are installed before changing from one pair of cylinders to another pair of cylinders. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Install" for the correct procedure.End By:
Install the engine oil pan.


Parts stator Force:

F505095-1
 
F505095-1 STATOR, ALTERNATOR
H0252H77B, H0254H75A, H0351H76K
F12366
 
F12366 STATOR PLATE
H0252H77B, H0254H75A, H0351H76K
F460664
 
F460664 STATOR GROUND WIRE
H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0352H77H, H0352H79L, H0353E91A, H0353E91B, H0353H78K, H0353H80M, H0353H81
F529095
 
F529095 STATOR, ALTERNATOR
H0202B81M, H0202H79K, H0252B83G, H0252H78D, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0352F90B, H0352F90C, H0353E91B, H0356F89B, H0357C86A, H0357C87A, H0357C88B, H0357F88A, H0357F89C, H0357G90A, H0357H83N
F4670664
Back to top