FA286582 Force STEERING ARM W/SPRING PIN & BUMPER


FA286582 STEERING ARM W/SPRING PIN & BUMPER Force H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0094H81F, H0095B81G, H0095H82H, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0125H79E, H0152B78D, H0152B83J, H0152C84K, H0152H79 STEERING
FA286582 STEERING ARM W/SPRING PIN & BUMPER Force
Rating:
13

Buy STEERING ARM W/SPRING PIN & BUMPER FA286582 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 90
 

Force entire parts catalog list:

H0091B80B 1980
H0091H79A 1979
H0091H83C 1983
H0091H84D 1984
H0092B80G 1980
H0092H79F 1979
H0092H81H 1981
H0092H81J 1981,1982
H0092H83K 1983
H0092H84L 1984
H0094H81F 1981,1982
H0095B81G 1981
H0095H82H 1982
H0101B78A 1978
H0102H76C 1976,1977
H0102H78E 1978
H0121B79A 1979
H0122H79E 1979
H0125H79E 1979
H0152B78D 1978
H0152B83J 1983,1984
H0152C84K 1984
H0152H79E 1979
H0152H80F 1980
H0152H81G 1981
H0152S89A 1989

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3939 Link Bracket 2
D 8T-5096 Dial Indicator 1
E 8T-3052 Degree Wheel 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01150312
Install dowel (8) in the crankshaft.Protrusion of dowel (8) from the crankshaft face ... 8.4 mm (0.33 inch)
Install dowel (9) in the crankshaft.Protrusion of dowel (9) from the crankshaft ... 4.1 0.5 mm (0.16 0.02 inch)
Install crankshaft gear (7) on the crankshaft with the keyway in alignment with dowel (9). Timing Mark "V" of the gear should face away from crankshaft (6).Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.
Install the upper halves of the main bearings in the cylinder block.Note: Ensure that the main bearings are installed so that the bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.
Illustration 2 g01150344
Install Tooling (A) and a suitable lifting device on each end of crankshaft (6). The weight of crankshaft (6) is approximately 188 kg (415 lb).
Install crankshaft (6) with Timing Mark "V" on the crankshaft gear in alignment with Timing Mark "V" on the cluster gear.
Install the thrust plates on each side of the No. 4 main bearing.Note: Install the thrust plates with the words "Block Side" toward the cylinder block.
Install the lower halves of the crankshaft main bearings in the main bearing caps.Note: Ensure that the main bearings are installed so that the bearing tabs fit into the notch in the main bearing cap.
Position main bearing caps (4) on the crankshaft.Note: Ensure that the numbers on the main bearing caps match the numbers on the cylinder block. Also ensure that the "FRONT" on the main bearing cap is installed toward the front of the cylinder block.
Lubricate the threads of bolts (3) with clean engine oil. Install bolts (3) and the washers.
Lubricate the threads of bolts (5) and the seal of the washer with clean engine oil. Install bolts (5) and the washers.Note: Inspect the washers that go on bolts (5).
Tighten bolts (3) and bolts (5) for the main bearing caps, as follows:
Tighten Bolt (A) to a torque of 258 14 N m (190 10 lb ft).Note: Bolt (A) is on the bearing tab side of the main bearing cap.
Tighten Bolt (B) to a torque of 258 14 N m (190 10 lb ft).Note: Bolt (B) is on the opposite side of the bearing tab of the main bearing cap.
Tighten Bolt (B) for an extra 120 5 degrees (2 flats).Note: If Tooling (E) is not used, place an index mark on the bolt and the main bearing cap.
Tighten Bolt (A) for an extra 120 5 degrees (2 flats).Note: If Tooling (E) is not used, place an index mark on the bolt and the main bearing cap.
Tighten Bolt (D) to a torque of 80 10 N m (59 7 lb ft).Note: Bolt (D) is on the opposite side of the bearing tab of the main bearing cap.
Tighten Bolt (C) to a torque of 80 10 N m (59 7 lb ft).Note: Bolt (C) is on the bearing tab side of the main bearing cap.
Rotate the crankshaft to ensure that the crankshaft turns freely.
Use Tooling (D) to check the crankshaft end play. Ensure that Tooling (D) is against a machined surface. The end play is controlled by the thrust plates of No. 4 main bearing (center).Crankshaft end play (new thrust plates) ... 0.10 to 0.60 mm (0.004 to 0.024 inch)Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the connecting rod bearings for final assembly.
Illustration 3 g01150364
Position the connecting rod against the crankshaft. Install connecting rod bearing cap (2) on the connecting rod.Note: Ensure that the number on the side of the connecting rod bearing cap is on the same side as the number on the connecting rod. The bearing tabs of the connecting rod bearing cap and the connecting rod are on the side opposite of the piston cooling jet.
Lubricate the threads of bolts (1) with clean engine oil. Install the bolts.
Tighten bolts (1), as follows:
Tighten Bolt (A) and Bolt (C) to a torque of 70 4 N m (52 3 lb ft).
Tighten Bolt (B) and Bolt (D) to a torque of 70 4 N m (52 3 lb ft).
Turn Bolt (B) and Bolt (D) for an extra 60 5 degrees (1/6 turn).Note: If Tooling (E) is not used, place an index mark on each bolt and connecting rod cap.
Tighten Bolt (A) and Bolt (C) again to a torque of 70 4 N m (52 3 lb ft).
Turn Bolt (A) and Bolt (C) for an extra 60 5 degrees (1/6 turn).Note: If Tooling (E) is not used, place an index mark on each bolt and connecting rod cap.
Rotate the crankshaft to ensure that the crankshaft turns freely.End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install".
Install the rear housing. Refer to Disassembly and Assembly, "Housing (Rear) - Install".
Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".


Parts steering Force:

FA456137
 
FA456137 STEERING HANDLE GRIP W/SLEEVE FOR MANUAL START MODELS
H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062H79M, H0070B79A, H0082H76G, H0082H79K, H0091H79A, H0091H83C, H0091H84D, H0092284D, H0092B80G, H0092H79F, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0101B78A, H0102H76C, H0102H78E, H0121B79
F286079-1
 
F286079-1 STEERING HANDLE
H0060B76A, H0062H79M, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0094H81F, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0152B78D, H0152B83J, H0152C84
F286573-1
 
F286573-1 STEERING FRICTION LAMP
H0060B76A, H0062H79M, H0064H78D, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91
818009 1
 
818009 1 STEERING HANDLE GEAR
H0060B76A, H0062H79M, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0101B78A, H0102H76C, H0102H78E, H0121B79
817751A 3
 
817751A 3 STEERING HANDLE BRACKET W/GREASE FITTING
H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0095B81G, H0095H82H, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0125H79
Back to top