F522532 Force STERN BRACKET - PORT


F522532 STERN BRACKET - PORT Force H0456B80L, H0457H82N, H0457H83P, H0503B83A, H0507H81A, H0507H82B, H0558H79L, H0559B80M, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84A, H0659B78B STERN
F522532 STERN BRACKET - PORT Force
Rating:
63

Buy STERN BRACKET - PORT F522532 Force genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$188.09

19-10-2024
25.0[11.25] pounds
US: Performance Rotors
98-00 Lexus GS400 - Rear Cross Drilled and Slotted Rotors
SP Performance Rotors
Number on catalog scheme: 30
 

Force entire parts catalog list:

H0456B80L 1980,1981
H0457H82N 1982
H0457H83P 1983,1984
H0503B83A 1983
H0507H81A 1981
H0507H82B 1982
H0558H79L 1979
H0559B80M 1980
H0559H77J 1977
H0559H78K 1978
H0559H80N 1980,1981
H0559H83R 1983
H0606H84A 1984,1985,1989
H0659B78B 1978

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1U-9744     Floor Jack     1    
Inspect all parts and clean all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Illustration 1 g00778822
Install a new gasket, four bolts (24) and the four washers in order to secure bonnet (25) and the two brackets to the transmission oil cooler. Install four bolts (23) in order to secure the top half of tube (11) to the oil cooler.
Illustration 2 g00779122
Place the oil cooler and suitable cribbing onto tool (A). Carefully position the oil cooler under the machine before using tool (A) to lift the oil cooler into position. The weight of the oil cooler is 50 kg (110 lb).
Illustration 3 g00778736
Install a new gasket, six bolts (21) and the six washers in order to secure the oil cooler to elbow (22) .
Illustration 4 g00778734
Install a new gasket and position bracket (20) to the machine. Install three bolts (19) and the three washers in order to secure the bracket to the machine.Note: The uppermost bolt can be installed from the top side of the machine.
Illustration 5 g00778733
Install exhaust pipe (17) into the exhaust tube and tighten two clamp bolts (18) to a torque of 82 13 N m (60 10 lb ft).
Illustration 6 g00778732
Connect exhaust pipe (17) to the turbocharger and install clamp (16). Tighten the clamp to a torque of 11 1.2 N m (8 1 lb ft).
Illustration 7 g00778256
Install bolt (14) and the washer in order to secure oil drain adapter (15) for the engine to the oil cooler. Do not tighten the bolt at this stage.
Illustration 8 g00778250
Install the bottom half of tube (11) to the top half of the tube and to the transmission. Install four bolts (13) and the four washers in order to secure the tube to the transmission. Install clamp (10) in order to secure the bottom half of the tube to the top half of the tube. Install bolt (12) in order to secure the clip to the oil cooler. Tighten the bolt that was left loose in step 8.
Illustration 9 g00777991
Install stud (9) into the transmission oil cooler. The stud should be installed with the tapered end toward the oil cooler.
Illustration 10 g00777988
Install block (8) onto the stud in the oil cooler. Refer to step 10. Install the two halves of tube (7) to the transmission and to the oil cooler. Install three bolts (5), the nut and the four washers in order to secure the tube and the block to the oil cooler.
Install four bolts (4) and the four washers in order to secure tube (7) to the transmission. Install clamp (6) in order to assemble the two halves of tube (7) .
Illustration 11 g00777985
Install bolt (3), the two washers and the nut in order to secure the wiring clip to the bracket. Install bolt (2), the two washers and the nut in order to secure the wiring clip to the bracket. Connect electrical connector (1) and replace the cable strap.End By:
Install the turbocharger guard. Refer to Disassembly and Assembly, "Turbocharger - Remove and Install".
Install the crankcase guards. Refer to Disassembly and Assembly, "Crankcase Guard - Remove and Install.".
Refill the torque converter and transmission oil. Refer to Operation and Maintenance Manual, "Torque Converter and Transmission oil - Change".
Refill the engine coolant. Refer to Operati


Parts stern Force:

FA433113
 
FA433113 STERN BRACKET LOCK BAR W/HANDLE
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0357C88B, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503H84B, H0504H88C, H0504H88D, H0507B85A, H0507C86A, H0507C87C, H0507C88B, H0507F87B, H0507F88A, H0507H81
F522032
 
F522032 STERN BRACKET - STARBOARD
H0456B80L, H0457H82N, H0457H83P, H0503B83A, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507C87C, H0507F87B, H0507F88A, H0507H81A, H0507H82B, H0558H79L, H0559B80M, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84A, H0659B78B
F522286
 
F522286 STERN BRACKET FRICTION WASHER
H0257F88A, H0257F88B, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0357C88B, H0357F89C, H0357G90A, H0407E92C, H0456B80L, H0457H82N, H0457H83P, H0503B83A, H0503H84B, H0504H88C, H0504H88D, H0504P89B, H0505C89B, H0507A89C, H0507A89
Back to top