681490 Force STOP, STARTER INTERIOCK


681490 STOP, STARTER INTERIOCK Force H0092S91A, H0093S91A STOP
681490 STOP, STARTER INTERIOCK Force
Rating:
8

Buy STOP, STARTER INTERIOCK 681490 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: L
 

Compatible models:

Force entire parts catalog list:

H0092S91A 1991
H0093S91A 1991

Information:

This procedure is for earlier 7000 series full injection nozzles with 55.12 mm (2.170 in) adapter bores.Start By:a. remove valve covers
Do not let the tops of the fuel nozzles turn when the fuel lines are loosened. The nozzles will be damaged if the top of the nozzles turn in the body.
1. Use Tool (A) to loosen fuel injection line (1) at the fuel injection nozzle. 2. Disconnect fuel injection line (2) from head adapter nut (3).3. Remove adapter nut (3) and the O-ring seal.4. Move adapter (4) out of valve cover base, and remove fuel injection line (1). 5. If necessary, remove seal (5) from fuel injection line (1). Clamp (6) cannot be removed until fuel injection nozzle (8) is lifted approximately 25.0 mm (1.00 in). 6. Remove bolt (7) that holds clamp (6).7. Remove fuel injection nozzle (8) with Tool (B) as follows: a. Install 6V6983 Adapter and 6V4152 Screw (9) part of Tool (B) into fuel injection nozzle (8).b. Install 6V6982 Tube Assembly (11) over the 6V4152 Screw. Use 2S5658 Washer and 1B2406 Nut (10) on the 6V4152 Screw to pull fuel injection nozzle (8) from the adapter. Items (10) and (11) are part of Tool (B).
A replacement of compression seal washer (13) and of carbon dam seal (12) must be made each time the fuel injection nozzle is removed. Be sure that the replacement compression seal washer (13) is the same color code and part number as the original compression seal washer. If the wrong thickness washer is used, engine damage could occur. See Specifications for 3412 Industrial and Marine Engines for more information.
8. Remove carbon dam seal (12) and compression seal washer (13) from fuel injection nozzle (8).Install Fuel Injection Nozzles (Earlier 7000 Series)
*part of 8S2245 Cleaning Tool Group Earlier fuel injection nozzles are installed in adapters that are below the surface of the cylinder head. 1. Use Tool (D) to clean adapter bore (1) for fuel injection nozzle. Use a tap driver to turn Tool (D). 2. Install compression seal washer (3) on fuel injection nozzle (4).3. Use Tool (A) to install carbon dam seal (2) on fuel injection nozzle (4). Refer to Special Instruction SEHS1292 for the use of Tool (C). 4. Install fuel injection nozzle (4) and clamp (5) as a unit. Install the bolt through the clamp into the adapter. 5. Install O-ring seal on fuel injection line (6), and put clean diesel fuel on it. 6. Install fuel injection line (6). Move adapter (7) into position in the rocker arm cover base.
Do not let the tops of the fuel nozzles turn when the fuel lines are tightened. The nozzles will be damaged if the top of the nozzles turn in the body.
7. Use Tool (B) to tighten the inner fuel line nuts to a torque of 41 7 N m (30 5 lb ft). 8. Put clean diesel fuel oil on O-ring seal (10). Install O-ring seal (10) and nut (9). Tighten nut (9) to a torque of 30 5 N m (22 4 lb ft).9. Install nut (8) for the fuel injection line, and tighten the fuel injection line nut to a torque of 41 7 N m (30 5 lb ft).10. After installation of the valve covers, bleed remove the air from the fuel system. See Testing and Adjusting for the correct procedure.End By:a. install valve covers


Parts stop Force:

F1997
 
F1997 STOP NUT, 8 - 32
H0091H83C, H0091H84D, H0092284D, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0095H82H, H0152B83J, H0152C84K, H0152S89A, H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75
F1803
 
F1803 STOP NUT
H0060B76A, H0062H79M, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H009201SD, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0095B80F, H0095B81G, H0095H82
F286490
 
F286490 STOP, STEERING HANDLE
H0060B76A, H0062H79M, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H009201RS, H009201SD, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0101B78A, H0102H76
F7026
 
F7026 STOP NUT
H0032H84G, H0042081C, H0042082D, H0042083E, H0042C84L, H0043F85A, H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0064H82H, H0071H84E, H0072B81D, H0072H82E, H0091H83C, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H81
F619161 1
 
F619161 1 STOP-REED (9.9 - BLACK)
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A
F715161
 
F715161 STOP (15)
H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A
F681490
 
F681490 STOP-STARTER PULLEY INTERLOCK
H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS, H025201US
7026
 
7026 STOP NUT
H0042C87A, H0092S91A, H0093S91A
Back to top