817750A 4 Force SWIVEL BRACKET W/GREASE FITTING


817750A 4 SWIVEL BRACKET W/GREASE FITTING Force H0091B80B, H0091H79A, H0091H83C, H0091H84D, H009201RS, H009201SD, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0095B81G, H0095H82H, H0101B78A, H0102H76C, H0102H78E, H0121B79 SWIVEL
817750A 4 SWIVEL BRACKET W/GREASE FITTING Force
Rating:
93

Buy SWIVEL BRACKET W/GREASE FITTING 817750A 4 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 75
 

Force entire parts catalog list:

H0091B80B 1980
H0091H79A 1979
H0091H83C 1983
H0091H84D 1984
H009201RS 1995
H009201SD 1996,1997
H0092284D 1984,1985,1986,1987,1988,1989,1990,1991,1992,1993,1994,1995
H0092B80G 1980
H0092H79F 1979
H0092H81H 1981
H0092H81J 1981,1982
H0092H83K 1983
H0092H84L 1984
H0092S88A 1988
H0092S91A 1991
H0093S91A 1991
H0094H81F 1981,1982
H0095B81G 1981
H0095H82H 1982
H0101B78A 1978
H0102H76C 1976,1977
H0102H78E 1978
H0121B79A 1979
H0122H79E 1979
H0125H79E 1979
H015201RS 1995
H015211SS 1996,1997
H0152B78D 1978
H0152B83J 1983,1984
H0152C84K 1984
H0152H79E 1979
H0152H80F 1980
H0152H81G 1981
H0152S89A 1989

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6192 Pliers 1
B 7M-3978(1) Piston Ring Expander Gp 1
7B-7974(2) Piston Ring Expander Gp 1
C 5P-8639 Hydraulic Press (Connecting Rod Bearing) 1
8F-0024 Hose Assembly 1
1P-2375 Connecting Coupler 1
1P-2376 Connecting Coupler 1
5P-8651 Spacer 1
5P-8649 Adapter 1
5P-8650 Bushing Adapter 1
9U-6600 Hand Hydraulic Pump 1
(1) For use with 137 mm (5.4 inch) bores.
(2) For use with 145 mm (5.7 inch) bores.Note: Prior to removal from the engine, the pistons and connecting rod assemblies were marked. The components must be reassembled together. The components must be installed in the original location in the engine. Do not interchange any of the components.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01017742
Illustration 2 g01018268
The connecting rod must be heated for the installation of the piston pin bearing. Do not use a torch.
Raise heat of connecting rod (6) along Length (Y). (Y) Maximum Length for heating the connecting rod ... 95 mm (3.7 inch)
Allow the connecting rod and the bearing to cool to room temperature.
Use Tooling (C) to remove the old bearing and install new bearing (7) at the same time. The adapter of Tooling (C) should make full contact with the surfaces of connecting rod (6). Note: Orient the bearing joint within 5 degrees of either Location (X).
Use a pin boring machine to machine the bore of bearing (7) to the correct diameter. Diameter of bearing bore ... 60.035 0.008 mm (2.3636 0.0003 inch)
Illustration 3 g01056145
Position the spring for the oil control piston ring in the oil ring groove in the piston body assembly.
Position oil control piston ring (3) over the spring. Position the oil control piston ring so that the gap is 180 degrees from the joint in the spring. Install the oil control piston ring on the piston with Tooling (B).
Use Tooling (B) to install intermediate piston ring (2) with the side that has the identification “UP-2” toward the top of the piston.
Use Tooling (B) to install top piston ring (1) with the side that has the identification “UP-1” toward the top of the piston.
Position piston rings (1), (2), and (3) so the gaps are 120 degrees from each other.
Check the clearance between the ends of piston rings (1), (2), and (3). Refer to Specifications, "Pistons And Rings".
Position piston body assembly (4) on connecting rod (6). Apply clean engine oil to connecting rod pin (8) and install the connecting rod pin. Install pin retainer (5) with Tooling (A).
Install upper connecting rod bearing (9) in connecting rod (6). Note: Ensure that the bearing locking tab is located in the notch of the connecting rod.
Install lower connecting rod bearing (10) in connecting rod bearing cap (11). Note: Ensure that the bearing locking tab is located in the notch of the connecting rod bearing cap.
Ensure that the dowels are installed in the connecting rod bearing cap. End By:
Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".


Parts swivel Force:

F184033-1
 
F184033-1 SWIVEL, CHOKE ROD
H0091H83C, H0091H84D, H0092H81J, H0095H82H, H0202B81M, H0202H79K, H0252B83G, H0252H77B, H0252H78D, H0254H75A, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0352H77H, H0352H79L, H0353E91A, H0353E91B, H0353H78
F681033
 
F681033 SWIVEL
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A
681033
 
681033 SWIVEL
H0092S91A, H0093S91A
Back to top