F563 Force TERMINAL BLOCK KIT

Table 1
Cross-Reference from Event Codes on Cat Data Link to Troubleshooting Procedure
Code and Description Troubleshooting Procedure
E096(1) High Fuel Pressure Troubleshooting, "Fuel Pressure Is High"
E172(1) High Air Filter Restriction Troubleshooting, "Inlet Air Is Restricted"
E172(2) High Air Filter Restriction
E194(2) High Exhaust Temperature Troubleshooting, "Exhaust Temperature Is High"
E265(3) User Defined Shutdown Troubleshooting, "Shutdown (Ground Level) - Test"
E360(1) Low Engine Oil Pressure Troubleshooting, "Oil Pressure Is Low"
E360(3) Low Engine Oil Pressure
E361(1) High Engine Coolant Temperature Troubleshooting, "Coolant Temperature Is High"
E361(2) High Engine Coolant Temperature
E362(2) Engine Overspeed Troubleshooting, "Engine Overspeeds"
E363(1) High Fuel Supply Temperature Troubleshooting, "Fuel Temperature Is High"
E363(2) High Fuel Supply Temperature
E390(1) Fuel Filter Restriction Troubleshooting, "Fuel Filter Is Restricted"
E390(2) Fuel Filter Restriction
E441(1) Idle Elevated to Increase Battery Voltage Troubleshooting, "Idle Speed Is High"
E539(1) High Intake Manifold Air Temperature Troubleshooting, "Intake Manifold Air Temperature Is High"
E539(2) High Intake Manifold Air Temperature Parts of the Event Code
Event Code - The "E" identifies the code as an event code. The "XXX(X)" represents a numeric identifier for the event code. The fourth "(X)" assigns one of three levels to the active event code according to the severity of the abnormal system condition. This is followed by a description of the code. Refer to the following example:
E360(1) Low Oil Pressure
E360(2) Low Oil Pressure
E360(3) Low Oil PressureThe definition for the levels of severity for an event are defined below:Level 1 - Level 1 alerts the operator that an engine system requires attention. The operator should check the involved system condition or the operator should perform maintenance on the involved system at the earliest possible time.Level 2 - Level 2 requires a change in the operation of the engine or the performance of a maintenance procedure. Failure to correct the problem that caused this warning may result in damage to the engine components.Level 3 - Level 3 requires an immediate safe shutdown of the engine in order to avoid damage to the engine or injury to personnel around the engine. The problem that caused the event must be corrected before engine operation can resume.Active Event Codes
An active event code represents a problem with engine operation. Correct the problem as soon as possible.Active event codes are listed in ascending numerical order. The code with the lowest number is listed first.Illustration 1 is an example of the operating range of a temperature sensor. Do not use the Illustration to troubleshoot temperature sensors.
Illustration 1 g01138880
Example of the typical operating range of a temperature sensor
(1) This area represents the normal operating range of the parameter. The normal output voltage of the sensor is between 0.2 VDC and 4.2 VDC.
(2) In this area, the temperature above 107 °C (225 °F) is higher than normal. The output voltage of the sensor will generate an event code. The sensor does not have an electronic problem.
(3) In these areas, the output voltage of the sensor is too high or too low. The voltage is outside of the normal range. The electronic problem will generate a diagnostic code. Refer to Troubleshooting, "Diagnostic Trouble Code List" for additional information on diagnostic codes. Logged Event Codes
When the Electronic Control Module (ECM) generates an event code, the ECM logs the code in permanent memory. The ECM has an internal diagnostic clock. The ECM will record the following information when an event code is generated:
The hour of the first occurrence of the code
The hour of the last occurrence of the code
The number of occurrences of the codeLogged events are listed in chronological order. The most recent event code is listed first.This information can be helpful for troubleshooting intermittent problems. Logged codes can also be used to review the performance of the engine.Clearing Event Codes
A code is cleared from memory when one of the following conditions occur:
The code does not recur for 100 hours.
A new code is logged and there are already ten codes in memory. In this case, the oldest code is cleared.
The service technician manually clears the code.Always clear logged event codes after investigating and correcting the problem which generated the code.Troubleshooting
For basic troubleshooting of the engine, perform the following steps in order to diagnose a malfunction:
Obtain the following information about the complaint:
The event and the time of the event
Determine the conditions for the event. The conditions will include the engine rpm and the load.
Determine if there are any systems that were installed by the dealer or by the customer that could cause the event.
Determine whether any additional events occurred.
Verify that the complaint is not due to normal engine operation. Verify that the complaint is not due to error of the operator.
Narrow the probable cause. Consider the operator information, the conditions of operation, and the history of the engine.
Perform a visual inspection. Inspect the following items:
Fuel supply
Oil level
Oil supply
Wiring
ConnectorsBe sure to check the connectors. This is very important for problems that are intermittent. Refer to Troubleshooting, "Inspecting Electrical Connectors".If these steps do not resolve the problem, refer to Table 1 for the procedure to troubleshoot the event code.Trip Points for the "Caterpillar Monitoring System"
The monitoring system determines the level of action that is taken by the ECM in response to a condition that can damage the engine. When any of these conditions occur, the appropriate event code will be generated.Table 2 contains the parameters that are monitored and the appropriate event code(s) that can be generated for that parameter. Table 2 also contains the minimum and maximum ranges for the parameter and the default trip points for each parameter. The actual settings for each parameter can be viewed with Caterpillar Electronic Technician (ET). The trip points for some of the parameters may be adjustable with Cat ET.
Table 2
Monitoring System Parameters
Parameter Action Delay Time in Seconds Trip Point Default State
Min Max Default Min Max