06942 Force THROTTLE SHUTTER RETAINING SCREW AND LOCKWASHER


06942 THROTTLE SHUTTER RETAINING SCREW AND LOCKWASHER Force H1209H76F THROTTLE
06942 THROTTLE SHUTTER RETAINING SCREW AND LOCKWASHER Force
Rating:
83

Buy THROTTLE SHUTTER RETAINING SCREW AND LOCKWASHER 06942 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

Compatible models:

H1209H76F   Force

Force entire parts catalog list:

H1209H76F 1976,1977

Information:

Introduction
This Special Instruction provides the procedure to repower a D9N Track-Type Tractor. The replacement engine for the machine will be a Tier II level 3408E Engine. The machine was originally equipped with a 3408B Engine. This Special Instruction will provide the information to install the Tier II level replacement engine.
Table 1
Engine Arrangement
Original Engine Replacement Engine
7W-2850 256-7537(1)
(1) New Repower EngineThis Special Instruction does not include procedures that can be found in your existing manuals. Refer to the original Service Manual, Parts Manual, and Operation and Maintenance Manual for more information.When you have completed this procedure, prepare the machine for service. Refer to the Operation and Maintenance Manual.Note: Do not perform any procedure in this Special Instruction until the information has been read and understood.Reference: Service Manual, Parts Manual, Operation and Maintenance Manual.Note: This instruction contains some procedures that come from dealer feedback. The emissions replacement engine is not a direct replacement. Additional parts and labor hours may be needed to complete this engine replacement. Variations in machine serial number breaks or options could cause discrepancy in the modifications, required parts, and labor hours to complete this procedure. This documentation is a guideline for Cat Dealer personnel to complete the repower procedure. If errors are found, submit feedback in SIS Web or contact the Emissions Solutions Group.Safety
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.
Do not attempt to assemble this machine until you read and you understand the assembly instructions.Improper assembly procedures could result in injury or death.
Personal injury or death can result from improper lifting or blocking.When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component.Approximate weights of the components are shown. Clean all surfaces where parts are to be installed.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Welding on Electronically Controlled Engines
Proper welding procedures are necessary to avoid damage to electronic controls. Perform welding on the engine according to the following procedure.
Set the engine control to the "STOP" mode.
Turn OFF the fuel supply to the engine.
Disconnect the negative terminal from the battery.
Disconnect the engine electronic components from the wiring harnesses: ECM, throttle actuator, actuator for the turbocharger compressor bypass, fuel metering valve and sensors.
Protect the wiring harnesses from welding debris and/or from welding spatter.
Do NOT use electrical components (ECM or sensors) or electronic component grounding points for grounding the welder.
Connect the ground cable of the welder directly to the engine component that will be welded. Place the clamp as close as possible to the weld to reduce the possibility of welding current damage.
Use standard welding procedures to weld the materials together.Required Parts
Refer to Parts Manual, SEBP4386.Note: The required parts are subject to some change. Refer to TMI for the most recent required parts list.Note: If part fabrication is necessary, ensure that all fabricated parts are deburred. Use caution when deburring parts. Avoid excessive grinding and notches.Note: A breakdown of the kit provides a parts list for the repower. The kit part number is not serviceable. Order the engine arrangement plus the list of parts provided in the kit.


Parts throttle Force:

FO3804
 
FO3804 THROTTLE SHAFT POSITION RETAINING SCREW WASHER
H0202B80L, H0202H79K, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0350H78L, H0351H76K, H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0357H83N, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0507H81A, H0507H82B, H0555H74
F333316
 
F333316 THROTTLE ROLLER SHAFT
H0091H83C, H0091H84D, H0092284D, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0095H82H, H0152B83J, H0152C84K, H0152S89A, H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75
F85502
 
F85502 THROTTLE LINK
H0033H75C, H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503B83A, H0503H84B, H0504H88C, H0504H88D, H0504P89B, H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90
F17014
 
F17014 THROTTLE ARM
H0091H83C, H0091H84D, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503B83A, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507F87B, H0507H81A, H0507H82B, H0555H74G, H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80
F17010-1
 
F17010-1 THROTTLE GEAR
H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503B83A, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507F87B, H0507H81A, H0507H82B, H0555H74G, H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84
FO16008
 
FO16008 THROTTLE SHAFT RETURN SPRING
H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0659B78B, H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0759H79A, H0850H79A, H0850H80A, H0850H81
FO15231
 
FO15231 THROTTLE SHAFT AND LEVER
H1000H79A, H1004H79A, H1006B80B, H1006B81C, H1007H79A, H1008H80A, H1057B78H, H1058H82G, H1059H76D, H1059H77G, H1159H77A, H1209H76F
FO13942
 
FO13942 THROTTLE SHUTTER
H1000H79A, H1004H79A, H1006B80B, H1006B81C, H1007H79A, H1008H80A, H1057B78H, H1058H82G, H1059H76D, H1059H77G, H1159H77A, H1209H76F
Back to top