F654029 Force TRIGGER ASSY.


F654029 TRIGGER ASSY. Force H1251A88A, H1251A88B, H1251A88C, H1251A89A, H1251A89B, H1251A89C, H1251A89D, H1251A89E, H1251F86A, H1251F87A, H1251F87B TRIGGER
F654029 TRIGGER ASSY. Force
Rating:
88

Buy TRIGGER ASSY. F654029 Force genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$408.95
 

31-10-2022

-: -
Chrysler Force Trigger Sensor 4 Cyl 120 Hp 1990-1991 Model# E000001 - E0006550 WSM 136-4029-4 OEM# F654029, F654029-1, 300-888797, 300-F654029-1
High Performace Quality OEM Style Trigger Sensors. || Trigger Sensor meets OEM standards or higher. || PWC Engine brings Higher Quality for an awesome price!
$408.95
 

31-10-2022

-: -
Force Trigger Sensor Compatible with Chrysler 4 Cyl 125 Hp 1986 Model# B WSM 136-4029-4 OEM# F654029, F654029-1, 300-888797, 300-F654029-1
High Performace Quality OEM Style Trigger Sensors. || Trigger Sensor meets OEM standards or higher. || PWC Engine brings Higher Quality for an awesome price!
$408.95
 

31-10-2022

-: -
Chrysler Force Trigger Sensor 4 Cyl 125 Hp 1987-1988 Model# A and B WSM 136-4029-4 OEM# F654029, F654029-1, 300-888797, 300-F654029-1
High Performace Quality OEM Style Trigger Sensors. || Trigger Sensor meets OEM standards or higher. || PWC Engine brings Higher Quality for an awesome price!
Number on catalog scheme: 58
 

Force entire parts catalog list:

H1251A88A 1988
H1251A88B 1988
H1251A88C 1988
H1251A89A 1989
H1251A89B 1989
H1251A89C 1989
H1251A89D 1989
H1251A89E 1989
H1251F86A 1986
H1251F87A 1987
H1251F87B 1987

Information:

Start By:a. disassemble governorb. remove fuel injection pumps
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Remove cover (1) and gasket. 2. Remove rack (2).
If the original lifters are to be installed in the fuel injection pump housing, put identification marks on them as to their location in the housing.
3. Remove lifters (3). 4. Put the fuel injection pump housing on end on blocks. Use tool (A) to remove snap ring (4). 5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump housing to loosen washer (5). Remove washer (5). 6. Remove camshaft (6). 7. Remove bearings (7) from the drive end of the fuel injection pump housing. 8. Remove bearings (8) from the governor end of the fuel injection pump housing.Assemble Fuel Injection Pump Housing
Be sure all oil passages are clear, and put clean oil on all parts before assembly. 1. Use tooling (B) to install bearing (10) in the governor end of the fuel injection pump housing with junction (joint) (11) toward the top of the fuel injection pump housing. Install the bearing so it is 0.25 0.20 mm (0.10 0.008 in) below the surface of the housing.2. Use tooling (B) to install bearing (9) in the governor end of the fuel injection pump housing so it is 7.16 0.13 mm (0.282 0.005 in) below the surface of the housing. 3. Use tooling (B) to install bearing (12) in the drive end of the fuel injection pump housing with the junction (joint) in the bearing toward the top of the fuel injection pump housing. Install the bearing so it is 1.00 0.25 mm (9.039 0.010 in) below the surface of the housing. 4. Install plate (13) of tooling (C) on the drive end of the fuel injection pump housing to install the bearing for the rack. Use clean grease to hold the new rack bearing on driver (14) of tooling (C). Install the driver and bearing in plate (13) with the groove in the driver in alignment with the pin in the plate and use a hammer to push the bearing into position. The bearing will be installed to the correct depth when the shoulder of the driver is against plate (13).5. Remove tooling (C) from the fuel injection pump housing. The rack bearing must be installed so it is 0.25 0.25 mm (0.010 0.010 in) below the surface of the housing. 6. Install camshaft (6).7. Put the fuel injection pump housing on end, and place a block under the camshaft. 8. Put washer (5) over the end of the camshaft and use tooling (B) and a spacer (15) that has an inside diameter of 38.1 mm (1.5 in) and a length of 31.75 mm (1.25 in) to push the washer against its seat on the camshaft. Camshaft must have 0.285 0.235 mm (0.0112 0.0093 in) end play when washer is pushed against cam shoulder. 9. Use tool (A) to install snap ring (4). 10. Install six lifters (3) in the fuel injection pump housing with the groove in the lifter in alignment with the pin in the housing. 11. Install rack (2) with the groove in the end of the rack in alignment with the ear (tab) of the rack bearing, at the drive end of the fuel injection pump housing. The six lifters are all the same and can be mixed. 12. Install the gasket and cover (1).End By:a. assemble governorb. install fuel injection pumps


Parts trigger Force:

F615029
TRIGGER ASSY.
F615029 TRIGGER ASSY.
H0906R83D, H1158H84G, H1251F84A, H1251F86A, H1251X85A, H1258H81A
Back to top