F307660-1 Force LEG EXHAUST TUBE


F307660-1 LEG EXHAUST TUBE Force H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503B83A, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507C87C, H0507F87B, H0507F88A, H0507H81A, H0507H82B, H0555H74 LEG
F307660-1 LEG EXHAUST TUBE Force
Rating:
53

Buy LEG EXHAUST TUBE F307660-1 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 92
 

Force entire parts catalog list:

H0352H77H 1977,1978
H0352H79L 1979
H0353H78K 1978
H0353H80M 1980
H0353H81N 1981
H0353H82P 1982
H0356H75F 1975,1976,1977
H0456B78J 1978
H0456B79K 1979
H0456B80L 1980,1981
H0457H82N 1982
H0457H83P 1983,1984
H0503B83A 1983
H0503H84B 1984
H0507B85A 1985
H0507C86A 1986
H0507C87A 1987
H0507C87C 1987
H0507F87B 1987
H0507F88A 1988
H0507H81A 1981
H0507H82B 1982
H0555H74G 1974,1976

Information:


Illustration 1 g02237473
Clean the mounting surface of the gasket.
According to need, apply the sealant to prevent the gasket falling off.
Apply the sealant (three Bond 1211) to the mating surface (1) of the crankcase and main bearing cap, and spread, the sealant evenly.
With aligning to the dowel pin, install the gasket and the front plate.
Tighten the front plate mounting bolts (2) to 12 1 N m (106 95 lb in).Installing camshaft
Note: Be careful not to damage camshaft journals, cams, and camshaft holes during insertion.
Illustration 2 g02237474
Apply engine oil to the camshaft journals and cams.
Slowly insert the camshaft assembly.
Illustration 3 g02237475
(4) Socket P/N:34491-00300
Tighten the thrust plate bolt (3) to 12 1 N m (106 9 lb in).
Make sure that the camshaft rotates lightly. Move the camshaft gear back and forth, and make sure that there is end play.Installing oil pump
Illustration 4 g02237476
Insert the oil pump to the oil pump hole on the crankcase. Then, make sure that the oil pump gear and oil pump drive gear on the camshaft meshes correctly.
From the crankcase side face, tighten the oil pump set bolts (6) with gasket (5) to 34 4 N m (301 35 lb in).Installing oil pan
Illustration 5 g02237477
Clean both side of the oil pan gasket contact surfaces and the contact surfaces of other parts thoroughly.
Apply the sealant (three bond 1212) to the mating surface clearance of the No.1 and No.4 main bearings and crankcase. The filling amount should be approx. 5.0 mm (0.20 inch) protruding from the mating surface clearance (A). Enough to spill out when the oil pan gasket is installed.
Install the oil pan gasket to the crankcase under face, with pushing the gasket circular part into the No.1 and No.4 main bearing cap grooves. Pushing the gasket protrusion into the mating surface clearance where sealant is filled.
For press oil pan tighten the mounting bolts (7) to 8 1 N m (71 9 lb in). For cast oil pan tighten the mounting bolts (7) to 30 3 N m (22 2 lb ft).Inverting crankcase
Note: Do not place the engine directly on the ground. It causes cracking the oil pan.
Illustration 6 g02237478
Attach the wire rope to the crankcase. Using a crane, hoist the crankcase and lay the crankcase with side faced downwards.
After that, hoist the crankcase again and invert the crankcase.Installing front idler gear
Illustration 7 g02237479
Timing gear train (8) Crankshaft gear (9) Inspection pump gear (10) Idler gear (11) Camshaft gear
Apply engine oil to the idler gear shaft (13) .
Install the idler gear with all match marks on it aligned with the marks on the other gears.
Illustration 8 g02237481
Install the thrust plate (12) with hole matching the pin of the idler gear shaft.
Tighten the thrust plate bolt to the specified torque.
Move the idler gear back and forth, and make sure that there is end play.Inspecting and adjusting timing gear after installation
Illustration 9 g02237482
Be sure to inspect and adjust the timing gear when the timing gear has been reassembled.
Table 1
Item     Standard     Limit    
Backlash     Crankshaft gear to idler gear    
0.030 to 0.160 mm (0.0012 to 0.0063 inch)    
0.250 mm (0.0098 inch) &


Parts leg Force:

FA435135
 
FA435135 LEG COVER (PORT)
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507C87C, H0507F87B, H0507F88A, H0555H74G
FA435145
 
FA435145 LEG COVER (STARBOARD)
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507C87C, H0507F87B, H0507F88A, H0555H74G
FA366135
 
FA366135 LEG COVER (PORT)
H0352H77H, H0352H79L, H0353H78K, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0555H74G
FA366145
 
FA366145 LEG COVER (STARBOARD)
H0352H77H, H0352H79L, H0353H78K, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0555H74G
Back to top