2862B6 1 Force WASHER


2862B6 1 WASHER Force H0092S91A, H0093S91A WASHER
2862B6 1 WASHER Force
Rating:
8

Buy WASHER 2862B6 1 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Compatible models:

Force entire parts catalog list:

H0092S91A 1991
H0093S91A 1991

Information:

This procedure is for earlier 7000 series fuel injection nozzles with 55.12 mm (2.170 in.) adapter bores.START BY:a. remove valve covers
Do not let the tops of the fuel nozzles turn when the fuel lines are loosened. The nozzles will be damaged if the top of the nozzles turn in the body.
1. Use tooling (A) to loosen fuel injection line (1) at the fuel injection nozzle. 2. Disconnect fuel injection line nut (2) from head adapter nut (3).3. Remove adapter nut (3) and the O-ring seal.4. Move adapter (4) out of the valve cover base, and remove fuel injection line (1). 5. If necessary, remove seal (5) from fuel injection line (1). Clamp (6) cannot be removed until fuel injection nozzle (8) is lifted approximately 25.0 mm (1.00 in.).6. Remove bolt (7) that holds clamp (6). 7. Remove fuel injection nozzle (8) with tooling (B) as follows:a. Install 6V6983 Adapter and 6V4152 Screw (9) [part of tooling (B)] into fuel injection nozzle (8).b. Install 6V6982 Tube Assembly (11) over the 6V4152 Screw. Use 2S5658 Washer and 1B2406 Nut (10) on the 6V4152 Screw to pull fuel injection nozzles (8) from the adapter. Items (10) and (11) are part of tooling (B).
A replacement of compression seal washer (13) and of carbon dam seal (12) must be made each time the fuel injection nozzle is removed. Be sure that the replacement compression seal washer (13) is the same color code and part number as the original compression seal washer. If the wrong thickness washer is used, engine damage could occur. See Specifications For 3408 Vehicular Engines for more information.
8. Remove carbon dam seal (12) and compression seal washer (13) from fuel injection nozzle (8).Install Fuel Injection Nozzles (Earlier)
Earlier fuel injection nozzles are installed in adapters that are below the surface of the cylinder head. 1. Use tool (D) to clean adapter bore (1) for the fuel injection nozzle. Use a tap driver to turn tool (D). 2. Install compression seal washer (3) on fuel injection nozzle (4).3. Use tool (A) to install carbon dam seal (2) on fuel injection nozzle (4). Refer to Special Instruction SEHS1292 for the use of tooling (C). 4. Install fuel injection nozzle (4) and clamp (5) as a unit. Install the bolt through the clamp into the adapter. 5. Install O-ring seal on fuel injection line (6), and put clean diesel fuel on it. 6. Install fuel injection line (6). Move adapter (7) into position in the rocker arm cover base.
Do not let the tops of the fuel nozzles turn when the fuel lines are tightened. The nozzles will be damaged if the top of the nozzles turn in the body.
7. Use tooling (B) to tighten the inner fuel line nuts to a torque of 41 7 N m (30 5 lb.ft.). 8. Put clean diesel fuel oil on O-ring seal (10). Install O-ring seal (10) and nut (9). Tighten nut (9) to a torque of 30 5 N m (22 4 lb.ft.).9. Install nut (8) for the fuel injection line, and tighten the fuel injection line nut to a torque of 41 7 N m (30 5 lb.ft.).10. After installation of the valve covers, bleed remove the air from the fuel system. See Testing And Adjusting for the correct procedure.END BY:a. install valve covers.


Parts washer Force:

F10242
 
F10242 WASHER
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201T
18552
 
18552 WASHER
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H0407E92C, H0706A91B, H0903E91
10242
 
10242 WASHER
H0092S91A, H0093S91A
8088
 
8088 WASHER
H0092S91A, H0093S91A
1907
 
1907 WASHER
H0092S91A, H0093S91A
525286
WASHER
525286 WASHER
H0092S91A, H0093S91A
8143
 
8143 WASHER, PLAIN #10
H0092S91A, H0093S91A
658504
 
658504 WASHER
H0093S91A
Back to top