24612-ZY9-000 Honda ARM, SHIFT


24612-ZY9-000 ARM, SHIFT Honda BF60AK1 LRTA, BF60AK1 XRTA, BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA ARM
24612-ZY9-000 ARM, SHIFT Honda
Rating:
58

Buy ARM, SHIFT 24612-ZY9-000 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

Honda entire parts catalog list:

BF60AK1 LRTA 2007
BF60AK1 XRTA 2007
BF75DK0 LHTA 2007
BF75DK0 LRTA 2007
BF75DK2 LRTA 2007
BF90DK0 LHTA 2007
BF90DK0 LRTA 2007
BF90DK0 XRTA 2007
BF90DK2 LRTA 2007
BF90DK2 XRTA 2007
BFP60AK1 LRTA 2007
BFP60AK1 LRTB 2007
BFP60AK1 XRTA 2007

Information:

start by:a) remove oil pumpb) remove oil pan plate 1. Remove the No. 1, 3, 5 and 7 main bearing caps (1). Remove the crankshaft thrust bearing from the No. 7 main bearing.2. Remove the lower half of the main bearing from the main bearing caps.
If the crankshaft is turned in the wrong direction, the tab on bearing will be pushed between the crankshaft and bearing area in block which can cause damage to the block or crankshaft.
3. Install tool (A) in the oil hole in the crankshaft journal and remove the upper half of the main bearing as the crankshaft is turned and the main bearing is moved out of the cylinder block. Install the main bearings dry when the clearance checks are made. Put clean engine oil on the main bearings for final assembly.
Make sure the upper and lower halves of the main bearings are installed so the bearing tabs fit into the notch in cylinder block and the main bearing caps.
4. Install new lower half of main bearings (2) in the main bearing caps. Use tool (A) and install the upper half of the main bearings in the cylinder block.5. Put clean oil on the thrust bearing and install a new thrust bearing for the No. 7 main bearing. Install the thrust bearing with the identification "BLOCK SIDE" toward the cylinder block and the tabs on the thrust bearings in the machined area in the cylinder block. The tabs will not let the thrust bearing be installed backward. When the bearing clearance is checked and the engine is in a vertical position, such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with the Plastigage. The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearances.6. Check the main bearing clearances with Plastigage (B) as follows: a) Put a piece of Plastigage (B) on the surface of the lower half of the main bearing.
Make sure the part number on the main bearing cap is toward the front of the engine and the number on the main bearing cap is the same as the number on the cylinder block on the left side of each main bearing cap.
Do not turn the crankshaft when Plastigage (B) is in position. b) Install main bearing caps (1) for No. 1, 3, 5 and 7 main bearings. Put clean engine oil on the bolt threads and the face of the washers and install the bolts. Tighten the bolts to a torque of 40 4 N m (30 3 lb.ft.).
Do not use an impact wrench to tighten the bolts the additional 90°.
c) Put a mark on each bolt and main bearing cap, then tighten the bolts 90° more.d) Remove the main bearings caps for No. 1, 3, 5 and 7 main bearings. Remove Plastigage (B) and measure the width of the Plastigage. The main bearing clearance must be 0.076 to 0.165 mm (.0030 to .0065 in.). Maximum permissible clearance with used bearings is 0.25 mm (.010 in.).7. Install main bearing caps (1) and tighten the bolts as in Steps 6b and 6c.8. Remove No. 2, 4 and 6 main bearing caps. Do Steps 2, 3, 4, 6 and 7 for the No. 2, 4 and 6 main bearings.
TYPICAL EXAMPLE9. Check the crankshaft end play with tooling (C). The end play is controlled by the thrust bearings on the No. 7 main bearing. End play with new bearings is 0.064 to 0.368 mm (.0025 to .0145 in.). The maximum permissible end play with used bearings is 0.64 mm (.025 in.).end by:a) install oil pan plateb) install oil pump


Parts arm Honda:

24845-ZV5-000
ARM, SHIFT LINK (Honda Code 3703170).
24845-ZV5-000 ARM, SHIFT LINK (Honda Code 3703170).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
24860-ZV5-000
ARM, LINK JOINT (Honda Code 3703212).
24860-ZV5-000 ARM, LINK JOINT (Honda Code 3703212).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
24845-ZW1-V01
ARM ASSY., SHIFT LINK (Honda Code 4898946).
24845-ZW1-V01 ARM ASSY., SHIFT LINK (Honda Code 4898946).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
24865-ZW1-V01
ARM ASSY., THROTTLE LINK (Honda Code 4898987).
24865-ZW1-V01 ARM ASSY., THROTTLE LINK (Honda Code 4898987).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
24813-ZW7-U01
ARM, NEUTRAL LOCK (Honda Code 6799571).
24813-ZW7-U01 ARM, NEUTRAL LOCK (Honda Code 6799571).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
17931-ZW4-H02
ARM, THROTTLE
17931-ZW4-H02 ARM, THROTTLE
BF25D4 LHA, BF25D4 LHTA, BF25D4 LRGA, BF25D4 LRTA, BF25D4 SHA, BF25D4 SHGA, BF25D4 SRGA, BF25D4 SRTA, BF25D5 LHA, BF25D5 LHTA, BF25D5 LRGA, BF25D5 LRTA, BF25D5 SHA, BF25D5 SHGA, BF25D5 SRGA, BF25D5 SRTA, BF25D6 LHA, BF25D6 LHTA, BF25D6 LRGA, BF25D6 L
17931-ZW4-H01
 
17931-ZW4-H01 ARM, THROTTLE (Honda Code 7744097).
BF25D4 LHA, BF25D4 LHTA, BF25D4 LRGA, BF25D4 LRTA, BF25D4 SHA, BF25D4 SHGA, BF25D4 SRGA, BF25D4 SRTA, BF25D5 LHA, BF25D5 LHTA, BF25D5 LRGA, BF25D5 LRTA, BF25D5 SHA, BF25D5 SHGA, BF25D5 SRGA, BF25D5 SRTA, BF25D6 LHA, BF25D6 LHTA, BF25D6 LRGA, BF25D6 L
14430-ZY9-000
ARM, IN. VALVE ROCKER
14430-ZY9-000 ARM, IN. VALVE ROCKER
BF60AK1 LRTA, BF60AK1 XRTA, BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
Back to top