13345-ZX2-003 Honda BEARING E, MAIN (LOWER) (PINK) (TAIHO)


13345-ZX2-003 BEARING E, MAIN (LOWER) (PINK) (TAIHO) Honda BF250A LA, BF250A XA, BF250A XCA, BF250A XXA, BF250A XXCA BEARING
13345-ZX2-003 BEARING E, MAIN (LOWER) (PINK) (TAIHO) Honda
Rating:
48

Buy BEARING E, MAIN (LOWER) (PINK) (TAIHO) 13345-ZX2-003 Honda genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$12.42
 

24-09-2017
.31[0.00] pounds
Honda: Honda
Honda 13345-ZX2-003 Bearing E, Main (Lower); 13345ZX2003 Made by Honda
HomeImprovement
Number on catalog scheme: 12
 

Honda entire parts catalog list:

BF250A LA 2007
BF250A XA 2007
BF250A XCA 2007
BF250A XXA 2007
BF250A XXCA 2007

Information:

Start By:a. remove air compressor 1. Disconnect the radiator hose from elbow (3).2. Remove two tube assemblies (2).3. Remove the bolts that hold elbow (3) to the water pump, and remove the elbow.4. Remove the bolts that hold elbow (1) to the water pump.5. Remove the bolts and retainers that hold elbow (1) to the tube assembly, and remove the elbow. 6. Remove the bolts and adapter assembly (4) from the front drive housing. 7. Remove O-ring seals (6) and (7) from adapter assembly (4).8. If necessary, remove bearing (5) from the adapter assembly. 9. Fasten a hoist and tooling (A) to water pump (8). Remove the bolts and the water pump from the front drive housing. The weight of the water pump is 25 kg (55 lb).10. Remove O-ring seal (9) from the water pump. The following steps are for installation of the Auxiliary Water Pump.11. Put O-ring seal (9) in position on the water pump. Put clean engine oil on the O-ring seal.12. Fasten a hoist and tooling (A) to water pump (8). Put the water pump in position on the front drive housing, and install the bolts that hold it. 13. If the bearing was removed from adapter assembly (4), align the hole in the bearing with the oil hole in the adapter assembly. Install the bearing with a press and tool (B). Install the bearing until it is 1.5 0.5 mm (.06 .02 in) below surface (X). The inside diameter of the bearing must be 75.000 0.055 mm (2.9528 .0022 in) after installation. 14. Put O-ring seals (6) and (7) in position on adapter assembly (4). Put clean oil on the O-ring seals.15. Put the adapter assembly in position on the front drive housing, and install the bolts that hold it. 16. Make sure the O-ring seal is in position on tube assembly (10). Put elbow (1) in position on the tube assembly, and install the retainers and bolts to hold it in place.17. Put the gasket in position between elbow (11) and the water pump, and install the bolts and nuts that hold the elbow to the water pump.18. Put the O-ring seal in position on the back of the water pump, and install elbow (3).19. Install two tube assemblies (2).20. Connect the radiator hose to elbow (3).End By:a. install air compressorDisassemble Auxiliary Water Pump
Start By:a. remove auxiliary water pump 1. Remove O-ring seals (3) and (4) from the pump housing.2. Remove the bolts and gear (2) from shaft (1). 3. Remove the bolts and adapter (5) from the pump housing. Remove the O-ring seal from adapter (5). 4. Loosen bolt (6) and the washer that hold impeller (7) to the shaft.5. Use tooling (A) to loosen impeller (7) from the end of the pump shaft. Remove tooling (A), bolt (6), the washer and impeller (7) from the pump shaft and housing. 6. Remove spring (9) from carbon seal assembly (10). Remove carbon seal assembly (10) from the end of shaft (8). 7. Remove the bolts that hold retainer washers (12) to the pump housing. Remove shaft (1) and washers (12) from the pump housing. 8. Remove the bolts that hold the shims and retainer washers (13) to the pump housing. Remove shaft (8), the shims and washers (13) from the pump housing.9. Remove the rubber ring and ceramic seal (11) from the pump housing. 10. Remove lip-type seal (14) from the pump housing. 11. Remove bearing (15) from the pump housing.Assemble Auxiliary Water Pump
1. Make sure the oil hole in the bearing is in alignment with the oil passage in housing (16). Use tool group (A) and a press to push the bearing in housing (16) until it is 1.5 0.5 mm (.06 .02 in) below the surface of housing (16). The inside diameter of the bearing must be 75.000 0.055 mm (2.9528 .0022 in). 2. Use tool group (A) to install the lip-type seal in housing (16). Make sure the lip of the seal is toward the bearing as shown. Put clean engine oil on the lip of the seal. 3. Install shaft (8) in the pump housing. Install retainer washers (13), the shims and bolts to hold shaft (8) in the pump housing. 4. Put clean engine oil on the bearing in the pump housing, and install shaft (1) and retainer washers (12) over shaft (8). Install the bolts to hold retainer washers (12) to the pump housing.
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surfaces of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
5. Install ceramic seal ring (11) in the rubber seal. Put clean water on the rubber seal and ceramic seal ring for lubrication. Use hand pressure and the tool (which is with the replacement seal group) to install the seal and seal ring as shown. 6. Remove the spring from carbon seal assembly (10). Put clean water on the inside diameter of the seal assembly for lubrication. Use hand pressure and the tool (which is with the replacement seal group) to push seal assembly (10) on the shaft until seal faces make light contact. 7. Install spring (9) on carbon seal assembly (10). 8. Put impeller (7) in position on the pump shaft as shown. 9. Install the bolt and washer that hold impeller to the pump shaft. Tighten the bolt to a torque of 38 4 N m (28 3 lb ft). 10. Install O-ring seal (17) around adapter (5) and put a small amount of clean engine oil or glycerin on it.11. Put adapter (5) in position, and install the bolts to hold it to the pump housing. 12. Put gear (2) in position on shaft (1), and install the bolts to hold gear (2). 13. Install O-ring seals (3) and (4) in the pump


Parts bearing Honda:

31111-PT0-003
BEARING, RR. GENERATOR (Honda Code 3275963).
31111-PT0-003 BEARING, RR. GENERATOR (Honda Code 3275963).
BF175AK1 LA, BF175AK1 XA, BF175AK1 XCA, BF175AK2 LA, BF175AK2 XA, BF175AK2 XCA, BF200A2 LA, BF200A2 XA, BF200A2 XCA, BF200A2 XXA, BF200A2 XXCA, BF200A3 LA, BF200A3 XA, BF200A3 XCA, BF200A3 XXA, BF200A3 XXCA, BF200A4 LA, BF200A4 XA, BF200A4 XCA, BF200
31114-PT0-013
BEARING, FR. GENERATOR (Honda Code 4483368).
31114-PT0-013 BEARING, FR. GENERATOR (Honda Code 4483368).
BF175AK1 LA, BF175AK1 XA, BF175AK1 XCA, BF175AK2 LA, BF175AK2 XA, BF175AK2 XCA, BF200A2 LA, BF200A2 XA, BF200A2 XCA, BF200A2 XXA, BF200A2 XXCA, BF200A3 LA, BF200A3 XA, BF200A3 XCA, BF200A3 XXA, BF200A3 XXCA, BF200A4 LA, BF200A4 XA, BF200A4 XCA, BF200
91001-ZY3-003
BEARING, NEEDLE (20X28X13) (Honda Code 7426364). (SOLID)
91001-ZY3-003 BEARING, NEEDLE (20X28X13) (Honda Code 7426364). (SOLID)
BF115DK1 LA, BF115DK1 XA, BF115DK1 XCA, BF135A4 LA, BF135A4 XA, BF135A4 XCA, BF135A5 LA, BF135A5 XA, BF135A5 XCA, BF135A6 LA, BF135A6 XA, BF135A6 XCA, BF135AK0 LA, BF135AK0 XA, BF135AK0 XCA, BF135AK2 LA, BF135AK2 XA, BF135AK2 XCA, BF150A4 LA, BF150A4
13211-RYE-A01
BEARING A, CONNECTING ROD (BLACK) (TAIHO)
13211-RYE-A01 BEARING A, CONNECTING ROD (BLACK) (TAIHO)
BF250A LA, BF250A XA, BF250A XCA, BF250A XXA, BF250A XXCA
13212-RYE-A01
BEARING B, CONNECTING ROD (BROWN) (TAIHO)
13212-RYE-A01 BEARING B, CONNECTING ROD (BROWN) (TAIHO)
BF250A LA, BF250A XA, BF250A XCA, BF250A XXA, BF250A XXCA
13213-RYE-A01
BEARING C, CONNECTING ROD (GREEN) (TAIHO)
13213-RYE-A01 BEARING C, CONNECTING ROD (GREEN) (TAIHO)
BF250A LA, BF250A XA, BF250A XCA, BF250A XXA, BF250A XXCA
13344-ZX2-003
BEARING D, MAIN (LOWER) (YELLOW) (TAIHO)
13344-ZX2-003 BEARING D, MAIN (LOWER) (YELLOW) (TAIHO)
BF250A LA, BF250A XA, BF250A XCA, BF250A XXA, BF250A XXCA
13346-ZX2-003
BEARING F, MAIN (LOWER) (RED) (TAIHO)
13346-ZX2-003 BEARING F, MAIN (LOWER) (RED) (TAIHO)
BF250A LA, BF250A XA, BF250A XCA, BF250A XXA, BF250A XXCA
Back to top