90008-ZY9-003 BOLT-WASHER (10X105) (Honda Code 8577850). Honda
BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA
BOLT
Price: query
Rating:
Compatible models:
Honda entire parts catalog list:
- CYLINDER BLOCK » 90008-ZY9-003
- CYLINDER BLOCK » 90008-ZY9-003
- CYLINDER BLOCK » 90008-ZY9-003
- CYLINDER BLOCK » 90008-ZY9-003
- CYLINDER BLOCK » 90008-ZY9-003
- CYLINDER BLOCK » 90008-ZY9-003
- CYLINDER BLOCK » 90008-ZY9-003
- CYLINDER BLOCK » 90008-ZY9-003
Information:
START BY:a. remove air conditioning compressor 1. Disconnect negative wire (3) from the terminal on the compressor.2. Remove plates (1) and (2) from the compressor. 3. Put tool (A) in a vise, and fasten the compressor to it as shown.4. Remove screws (4) and dust cover (5) from the drive plate. 5. Use the 5P7417 Wrench (6) from tooling (B) to hold the drive plate while the nut is removed from the compressor shaft. 6. Install the 5P7415 Puller (7) from tooling (B) on the drive plate. Be sure the puller is fully engaged in the drive plate. Use puller (7) to pull drive plate (8) off the compressor shaft. Remove the key from the drive plate. 7. Use a screwdriver to remove shield (9) [part of the bearing shield assembly] from the pulley. 8. Use a screwdriver to remove the remainder of bearing shield (10) from the pulley. 9. Use the 1P1863 External Retaining Ring Pliers (11) from tooling (B) to remove snap ring (12) from the shaft for the pulley. 10. Use the 5P7411 Pulley Puller Group (13) and the 5P7394 Puller Adapter (14) both from tooling (B) to pull the clutch and pulley assembly off the shaft. 11. Use the 5P7384 Pulley Bearing Remover and 5P7400 Driver Handle (15) both from tooling (B) to remove the bearing from clutch and pulley assembly (16).Install Compressor Clutch And Pulley
Do not use the inner race to install the bearing. The bearing must turn freely after it is installed.
1. Clean the new bearing. Use 5P7400 Driver Handle (1) and 5P7388 Bearing And Pulley Installer (2) from tooling (B) to install bearing (3) in the clutch and pulley assembly. 2. Use the 5P7400 Driver Handle (1) and the 5P7388 Bearing And Pulley Installer (2) from tooling (B) to install clutch and pulley assembly (4) on the compressor. 3. Use the 1P1863 External Retaining Ring Pliers (5) to install retainer ring (6). The flat surface of the ring must be toward the bearing.
It is very important to keep all foreign material out of the bearing and the area below the bearing. DO NOT use air pressure.
4. Thoroughly clean the top of the clutch and pulley assembly and the area of the bore for the shield assembly.5. Install a new bearing shield retainer (8) with driver handle (1) and 5P7418 Dust Shield Retainer Installer (7). 6. Use 5P7416 Shield Installer (9) and the 5P7411 Pulley Puller Group both from tooling (B) to install a new shield (10).
When the drive plate is ready for installation, clean the friction surfaces of the drive plate and the clutch and pulley assembly. DO NOT use any lubricant.
7. Install square key (11) in the groove in drive plate (12).
Never use a hammer to install the drive plate. The compressor is easily damaged.
8. Put the groove on the compressor shaft in alignment with the key in the drive plate. Install the drive plate. 9. Use 5P7423 Hub and Drive Plate Installer (13) from tooling (B) to install drive plate (12) onto the shaft until there is approximately 2.38 mm (.094 in.) clearance between the friction surfaces of the drive plate and clutch and pulley assembly (4). 10. Install a new nut on the compressor shaft. Use 5P7417 Clutch Hub Holding Wrench (14) to hold the drive plate while the nut on the compressor shaft is tightened to a torque of 19 to 22 N m (14 to 16 lb.ft.). 11. Use a feeler gauge (15) to check the clearance between the friction surfaces of the drive plate and clutch and pulley assembly. The clearance must now be 0.56 to 1.45 mm (.022 to .057 in.). The clutch and pulley assembly must turn freely. 12. Put dust cover (16) in position on the drive plate, and install the screws that hold it in place. 13. Install plate (17) on the compressor as shown. Install plate (18) and negative wire (19) on the compressor as shown. Connect the wire to the terminal on the clutch coil.14. Install the air conditioning compressor. See Install Air Conditioning Compressor.15. Start the engine and operate the air conditioning system. Turn the unit off and on at least twenty times at approximately one second intervals. This will let the clutch and pulley assembly engage the drive plate correctly during normal operation.
Do not use the inner race to install the bearing. The bearing must turn freely after it is installed.
1. Clean the new bearing. Use 5P7400 Driver Handle (1) and 5P7388 Bearing And Pulley Installer (2) from tooling (B) to install bearing (3) in the clutch and pulley assembly. 2. Use the 5P7400 Driver Handle (1) and the 5P7388 Bearing And Pulley Installer (2) from tooling (B) to install clutch and pulley assembly (4) on the compressor. 3. Use the 1P1863 External Retaining Ring Pliers (5) to install retainer ring (6). The flat surface of the ring must be toward the bearing.
It is very important to keep all foreign material out of the bearing and the area below the bearing. DO NOT use air pressure.
4. Thoroughly clean the top of the clutch and pulley assembly and the area of the bore for the shield assembly.5. Install a new bearing shield retainer (8) with driver handle (1) and 5P7418 Dust Shield Retainer Installer (7). 6. Use 5P7416 Shield Installer (9) and the 5P7411 Pulley Puller Group both from tooling (B) to install a new shield (10).
When the drive plate is ready for installation, clean the friction surfaces of the drive plate and the clutch and pulley assembly. DO NOT use any lubricant.
7. Install square key (11) in the groove in drive plate (12).
Never use a hammer to install the drive plate. The compressor is easily damaged.
8. Put the groove on the compressor shaft in alignment with the key in the drive plate. Install the drive plate. 9. Use 5P7423 Hub and Drive Plate Installer (13) from tooling (B) to install drive plate (12) onto the shaft until there is approximately 2.38 mm (.094 in.) clearance between the friction surfaces of the drive plate and clutch and pulley assembly (4). 10. Install a new nut on the compressor shaft. Use 5P7417 Clutch Hub Holding Wrench (14) to hold the drive plate while the nut on the compressor shaft is tightened to a torque of 19 to 22 N m (14 to 16 lb.ft.). 11. Use a feeler gauge (15) to check the clearance between the friction surfaces of the drive plate and clutch and pulley assembly. The clearance must now be 0.56 to 1.45 mm (.022 to .057 in.). The clutch and pulley assembly must turn freely. 12. Put dust cover (16) in position on the drive plate, and install the screws that hold it in place. 13. Install plate (17) on the compressor as shown. Install plate (18) and negative wire (19) on the compressor as shown. Connect the wire to the terminal on the clutch coil.14. Install the air conditioning compressor. See Install Air Conditioning Compressor.15. Start the engine and operate the air conditioning system. Turn the unit off and on at least twenty times at approximately one second intervals. This will let the clutch and pulley assembly engage the drive plate correctly during normal operation.
Parts bolt Honda:
92101-05016-4J
92101-05016-4J BOLT, HEX. (5X16) (Honda Code 3706959).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
90110-881-000
90110-881-000 BOLT, HEX. (6X14) (Honda Code 3174927).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
90019-ZW9-000
90019-ZW9-000 BOLT, FLANGE (6X35) (Honda Code 6643894).
BF115A6 LA, BF115A6 LCA, BF115A6 XA, BF115A6 XCA, BF115AK0 LA, BF115AK0 XA, BF15D3 LGA, BF15D3 LHA, BF15D3 LHGA, BF15D3 LHSA, BF15D3 LHTA, BF15D3 LRA, BF15D3 LRTA, BF15D3 SHA, BF15D3 SHGA, BF15D3 SHSA, BF15D3 SHTA, BF15D3 SRTA, BF15D3 XHA, BF15D3 XHG
90154-ZW9-000
90154-ZW9-000 BOLT, FLANGE (10X25) (Honda Code 6644066).
BF115DK1 LA, BF115DK1 XA, BF115DK1 XCA, BF15D3 LGA, BF15D3 LHA, BF15D3 LHGA, BF15D3 LHSA, BF15D3 LHTA, BF15D3 LRA, BF15D3 LRTA, BF15D3 SHA, BF15D3 SHGA, BF15D3 SHSA, BF15D3 SHTA, BF15D3 SRTA, BF15D3 XHA, BF15D3 XHGA, BF15D4 LGA, BF15D4 LHA, BF15D4 LH
90169-ZW4-000
90169-ZW4-000 BOLT, FLANGE (6X25) (SH) (Honda Code 7219942).
BF25A2 LHSA, BF25A2 LRSA, BF25A2 SHSA, BF25A2 SRSA, BF25A2 XRSA, BF25A3 LHSA, BF25A3 LRSA, BF25A3 SHSA, BF25A3 SRSA, BF25A3 XRSA, BF25D4 LHTA, BF25D4 LRGA, BF25D4 LRTA, BF25D4 SHGA, BF25D4 SRGA, BF25D4 SRTA, BF25D5 LHTA, BF25D5 LRGA, BF25D5 LRTA, BF2
90147-ZW4-000
90147-ZW4-000 BOLT, FLANGE (6X55) (Honda Code 7207566).
BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA, BF115A6 LA, BF115A6 LCA, BF115A6 XA, BF115A6 XCA, BF115AK0 LA, BF115AK0 XA, BF130A3 LA, BF130A3 LCA,
90159-ZW4-000
90159-ZW4-000 BOLT, FLANGE (10X35) (Honda Code 7207640).
BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA, BF115A6 LA, BF115A6 LCA, BF115A6 XA, BF115A6 XCA, BF115AK0 LA, BF115AK0 XA, BF130A3 LA, BF130A3 LCA,
90214-HW1-671
90214-HW1-671 BOLT, FLANGE (6X25) (SUS-D)
BF40DK2 LHA, BF40DK2 LRTA, BF50DK2 LRTA, BF50DK2 XRTA, BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA