92201-06025-0B BOLT, HEX. (6X25) (Honda Code 3753696). Honda
BF8AM LA, BF8AM SA, BF8AM XA
BOLT
Price: query
Rating:
Honda entire parts catalog list:
- RECOIL STARTER » 92201-06025-0B
- RECOIL STARTER » 92201-06025-0B
- RECOIL STARTER » 92201-06025-0B
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 334-0114 Mounting Bar 2
B - Guide Stud
5/8 - 11 by 20 inch 4
8T-4122 Hard Washer 4
6V-4803 Thrust Bearing 4
4K-0367 Full Nut 8
C 4C-5591 Anti-Seize Compound -
D - Scotch Brite 1 Start By:
Remove the heat exchanger. Refer to Disassembly and Assembly, "Heat Exchanger - Remove". Note: The following story is for 373-2564 Sea Water Heat Exchanger Gp.Note: The disassembly procedure can be performed on the engine.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all hose assemblies and all plate assemblies for installation purposes. Plug all hose assemblies to prevent fluid loss, and to keep contaminants from entering the systems.
Illustration 1 g02149026
Use suitable cribbing to place the heat exchanger in a flat position on the rear frame. This position can help ensure proper alignment during the procedure.
Remove bolts (1) and the spacers. Install Tooling (B).
Apply Tooling (C) to the threads of the nut and the threads of the guide stud prior to installation. Install the thrust bearing, the hard washer, and the nuts on the guide stud. Ensure that Tooling (B) is securely installed.
Place two nuts together and tighten the outer nut in order to install Tooling (B). Position the thrust bearing, the hard washer, and one nut against the front frame.
Illustration 2 g02149025
Remove bolts (3) and the spacers from front frame (2). Install Tooling (A) in the rear frame.
Illustration 3 g02149028
Remove bolts (4) and spacers (5).
Illustration 4 g02149027
Loosen the nuts on Tooling (B) evenly. Ensure that Tooling (B) does not loosen from the rear frame. Note: Do not loosen the nuts more than one turn per nut until the heat exchanger plates are no longer compressed.Note: As the front frame rises, the heat exchanger plates will slide along Tooling (A).
Remove Tooling (B). Note: Note the order and orientation of the heat exchanger plates and the seals during removal.
Remove front frame (2), heat exchanger plates (6), and the seals. Note: A seal may stick to the front frame during removal.Note: Check the O-ring seals and the seals for wear or for damage. Replace the components, if necessary.
Illustration 5 g02149033
Remove seals (7) from the elbows and rear frame (8).
Illustration 6 g02720226
Remove the zinc plugs from elbow (19) and elbow (20). Remove elbow (19) and elbow (20) from rear frame (8). Note the orientation of the elbows prior to removal.
Remove bolts (9). Remove cover (10) and O-ring seal (13). Remove water temperature regulators (15). Remove lip seals (18) from rear frame (8).
Remove pressure cap (11).
Remove bolts (14).
Remove filler neck (16). Remove O-ring seal (17).
Remove hose connector (12) from the filler neck. Instructions for Cleaning
Clean the plates with a coarse nylon brush or new Tooling (D).
Do not use a dirty Tooling (D), steel wool, or a wire brush, which may scratch the titanium plates. Any iron scratches in the titanium plates can lead to corrosion of the plates.
The recommended cleaning solution for scale buildup (calcium carbonate) and sediment buildup (corrosion products) is a 4 percent solution of nitric, citric, or sulfuric acid.
The recommended cleaning solution for cleaning biological growth is a 4 percent solution of sodium hydroxide.
Rinse plates thoroughly with water.
Parts bolt Honda:
90105-ZV4-650
90105-ZV4-650 BOLT, OIL CHECK (8X8) (Honda Code 3744802).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
90124-ZV4-000
90124-ZV4-000 BOLT, HEX. (6X20) (Honda Code 2945012).
BF135A4 LA, BF135A4 XA, BF135A4 XCA, BF135A5 LA, BF135A5 XA, BF135A5 XCA, BF135A6 LA, BF135A6 XA, BF135A6 XCA, BF150A4 LA, BF150A4 XA, BF150A4 XCA, BF150A5 LA, BF150A5 XA, BF150A5 XCA, BF150A6 LA, BF150A6 XA, BF150A6 XCA, BF15A1 LA, BF15A1 LAS, BF15A
90109-ZV4-000
90109-ZV4-000 BOLT, SPECIAL (8X20) (Honda Code 2740868).
BF15A1 LA, BF15A1 LAS, BF15A1 SA, BF15A1 SAS, BF15A1 XAS, BF15A2 LA, BF15A2 LAS, BF15A2 SA, BF15A2 SAS, BF15A2 XAS, BF15AM LA, BF15AM LAS, BF15AM SA, BF15AM SAS, BF15AM XAS, BF15AW LA, BF15AW LAS, BF15AW SA, BF15AW SAS, BF15AW XAS, BF15AX LA, BF15AX
90108-881-000
90108-881-000 BOLT, HEX. (6X28) (Honda Code 0814616).
BF15A1 LA, BF15A1 LAS, BF15A1 SA, BF15A1 SAS, BF15A1 XAS, BF15A2 LA, BF15A2 LAS, BF15A2 SA, BF15A2 SAS, BF15A2 XAS, BF15AM LA, BF15AM LAS, BF15AM SA, BF15AM SAS, BF15AM XAS, BF15AW LA, BF15AW LAS, BF15AW SA, BF15AW SAS, BF15AW XAS, BF15AX LA, BF15AX
95701-06035-02
95701-06035-02 BOLT, FLANGE (6X35) (Honda Code 2801355).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115AX LA, BF115AX LCA, BF115AX XA, BF115AX XCA, BF115AY LA, BF115AY LCA, BF115AY XA, BF115AY XCA, BF130A1 LA, BF130A1 LCA, BF130A1 XA, BF130A1 XCA,
90107-881-000
90107-881-000 BOLT, STRAIGHT SLOT (4X6) (Honda Code 0499434).
BF8A3 LA, BF8A3 SA, BF8A4 LA, BF8A4 SA, BF8A5 LA, BF8A5 SA, BF8A6 LA, BF8A6 SA, BF8AK0 LA, BF8AK0 SA, BF8AM LA, BF8AM SA, BF8AM XA, BF8AW LA, BF8AW SA, BF8AW XA, BF8AX LA, BF8AX SA, BF8AX XA, BF8AY LA, BF8AY SA, BF8AY XA
90016-920-000
90016-920-000 BOLT, FLANGE (6X12) (Honda Code 0285593).
BF15A1 LA, BF15A1 LAS, BF15A1 SA, BF15A1 SAS, BF15A1 XAS, BF15A2 LA, BF15A2 LAS, BF15A2 SA, BF15A2 SAS, BF15A2 XAS, BF15AM LA, BF15AM LAS, BF15AM SA, BF15AM SAS, BF15AM XAS, BF15AW LA, BF15AW LAS, BF15AW SA, BF15AW SAS, BF15AW XAS, BF15AX LA, BF15AX
95701-06025-02
95701-06025-02 BOLT, FLANGE (6X25) (Honda Code 2801330).
BF115AX LA, BF115AX LCA, BF115AX XA, BF115AX XCA, BF115AY LA, BF115AY LCA, BF115AY XA, BF115AY XCA, BF130AX LA, BF130AX LCA, BF130AX XA, BF130AX XCA, BF130AY LA, BF130AY LCA, BF130AY XA, BF130AY XCA, BF15A1 LA, BF15A1 LAS, BF15A1 SA, BF15A1 SAS, BF15