95701-10105-08 Honda BOLT, FLANGE (10X105) (Honda Code 3169216).

Excavator Application ENGINE MODEL AND ENGINE NUMBER
Model, Classification, and Use
Engine model embossment and engine number stamp
(1) Embossment of engine model and cylinder volumeThe engine model and cylinder volume are embossed on the side of injection pump mounting portion of the cylinder block.
Engine Model and Cylinder Volume(2) Engine number stampThe engine number is stamped on the injection pump mounting portion of the cylinder block (on the upper side of the tie rod cover).It is a serial number beginning with 1001 as shown below.
Engine NumberSECTIONAL VIEWS
Longitudinal Section (L3C)
Cross Section (L3C)
Sectional Views of Governor (L3C)
Oil Pump and Oil FilterFEATURES
1. Aim of developmentThe L series aim at the through going compact, lightweight engines which are suitable for superseding gasoline engines to power lawn mowers, vehicles, etc. The high-speed (3600 rpm continuous) specification engines are also available to apply them to the generators, welders, and marine use. The L series are the smallest and lightest water-cooled diesel engines in the world.2. Features of the new series(1) Small and lightweight engineThe new L series are 10 to 20% smaller in weight and 15 to 20% smaller in contour volume than the same class of engines of competitors.(2) Low noise and economical fuel consumptionLow noise and economical fuel consumption are attained by the well designed cylinder block construction (having curved side faces), the rearranged combustion chambers, and the small-sized fuel injection system.
Injection Pump(3) Easy startingThe engine can be started instantly only by keeping the starting switch key in the ON position for about 6 seconds to allow automatic feeding of current to the glow plugs, eliminating the necessity of setting the key to the HEAT position. (For engines with the automatic glow plug system.)The new governor mechanism also contributes to easy engine start, because it increases fuel injection and delays injection timing for easy engine start without necessity of moving the throttle lever to the "full throttle" position.(4) Multipurpose engineThe L series engine can be equipped with various kinds of optional devices.
Nozzle Holders and Return PipePerformance Curves
L2 Series Performance Curves
L2A
L2C
L2EDIN 6270 : NETBarometric pressure : 736mmHgAmbient temperature : 20°CVapor pressure : 10.5mmHgL3 Series Performance Curves
L3A
L3C
L3CDIN 6270 : NETBarometric pressure : 736mmHgAmbient temperature : 20°CVapor pressure : 10.5mmHgENGINE SPECIFICATIONS
MAINTENANCE
Engine oil and oil filter
1. Checking and correcting the engine oil level.(1) Place the engine horizontally.(2) Check the oil level with the oil level gauge. If the oil level has fallen to the lower limit, add oil up to the upper limit.(3) Check the oil level before (everyday) operation of the engine. CAUTION* Whenever oil is added, check the oil level again after waiting for about 1 minute.* When adding oil, use only the same engine oil as used in the engine.* When checking the oil level in an engine which has been long out of use, run the engine for several minutes, stop the engine, and check the oil level after a while.
Checking Oil Level
Oil Level Gauge2. Oil change intervalsChange the oil after initial 50-hour operation of a new engine and, thereafter, every 100 hours of operation.Replace the oil filter after initial 50-hour operation of a new engine and, thereafter, every 200 hours of operation.3. Engine oil to be usedEngine oil must conform to the API classification and viscosity number specified in the table at right. 4. When replacing the oil filter, use only the genuine replacement filter.
Oil Filter5. Changing the oilTo change oil, first warm up the engine and remove the drain plug to let oil drain completely. Put back the drain plug and refill the oil pan with fresh engine oil through the oil filler.* Oil pan drain plug tightening torque: 5.0 - 6.0 kgf m [49 - 59 N m]* Oil capacity (Upper limit/Lower limit) 6. Replacing the oil filter(1) Remove the oil filter with a filter wrench or the like.(2) Thoroughly clean the filter mounting surface of the filter bracket. Install the new filter with the O-ring coated with engine oil and tighten securely by hand.* Tightening torque:1.0 - 1.3 kgf m [9.8 - 12.7 N m] CAUTION Be careful not to twist the O-ring.(3) Run the engine for several minutes and make sure that no oil leaks.(4) After stopping the engine, check the oil level. If necessary, add oil.
Oil Filter WrenchRetightening the cylinder head bolts
When retightening the cylinder head bolts, draw out coolant, loosen the bolts slightly, and then retighten the bolts to the specified torque in the numerical order illustrated at right.* Tightening torque: M10 bolt 7.5 - 8.5 kgf m [73.5 - 83.4 N m]M8 bolt 2.0 - 3.0 kgf m [19.6 - 29.4 N m]The rocker assembly (the rocker arms, shaft, and stays) is to be kept removed when the cylinder head bolts are retightened.* Rocker stay tightening torque: M8 bolt 1.5 - 2.2 kgf m [14.7 - 21.6 N m]
Cylinder Head Bolt Tightening Sequence (L2)
Cylinder Head Bolt Tightening Sequence (L3)Adjusting the valve clearance
CAUTION Be sure to retighten the cylinder head bolts before adjusting the valve clearance.(1) Set the cylinder to be adjusted to the top dead center of compression stroke.* Valve clearance: 0.25 mm (cold) for both intake and exhaust valves(2) The top dead center of compression stroke can be obtained by aligning the T.D.C. (Top Dead Center) mark (notch) on the crankshaft pulley with the mark on the gear case.(3) First align the T.D.C. mark for the No. 1 cylinder.Confirm that the valves do not move up and down when the crankshaft is turned about 20 in normal direction of rotation and in reverse direction.(4) When setting the top dead center for the No. 2 cylinder and that for the No. 3 cylinder, perform as follows:
Adj