04601-881-000ZA Honda BRACKET KIT, STERN *NH282MU* (Honda Code 8020463). (OYSTER SILVER METALLIC-U)

Section A-ABore diameters in the cylinder block for the cylinder block liners:Position (A) ... 151.50 0.03 mm (5.965 .001 inch)Position (B) ... 149.8 0.3 mm (5.898 .012 inch)Position (C) ... 148.00 0.03 mm (5.827 .001 inch)Position (D) ... 141.90 0.15 mm (5.587 .006 inch) (4) The dowels extend past the top surface of the cylinder block by the following distance ... 10.0 0.5 mm (.39 .02 inch)(5) Distance from the centerline of the crankshaft bore to the top surface of the cylinder block ... 387.00 (15.236 inch)(6) Diameter of the camshaft bores ... 81.000 0.015 mm (3.1890 .0006 inch)(7) Bolt Tighten the bolt that holds the piston cooling jet to the following torque ... 35 3 N m (26 2 lb ft)The flatness of the top contact surface of the cylinder block must be within 0.05 mm (.002 inch) for any 150 mm (5.9 inch) section of the surface.(8) Width of main bearing cap ... 175.000 0.020 mm (6.8898 .0008 inch)Width in cylinder block for the main bearing cap ... 175.000 0.018 (6.8898 .0008 inch)(9) Distance from the centerline of the crankshaft to the bottom surface of the cylinder block ... 120.0 mm (4.72 inch)(10) Main bearing cap boltsUse the following procedure to install the main bearing cap bolts:1. Orient the main bearing cap correctly. The part number on the main bearing cap must face to the right and to the front face of the cylinder block. Also, the tab slots that are in the cylinder block and the main bearing caps must be adjacent. The main bearing caps are marked with identification numbers 1 through 7. Install the main bearing caps into the correct positions.2. Lubricate the main bearing cap bolts. Use "SAE 30W" oil or molybdenum grease to lubricate the threads and the washer face.3. Tighten the main bearing cap bolts. Tighten bolts to the following torque ... 95 5 N m (70 4 lb ft)4. Put an alignment mark on each cap and bolt. Rotate the bolts in the clockwise direction ... 90 5 degrees(11) Bore in the cylinder block for the seven main bearings ... 116.000 0.013 mm (4.5669 .0005 inch)
View B-BThe camshaft bearings are installed into the cylinder block at the values that follow:Position (A) ... 35.20 mm (1.386 inch)Position (B) ... 191.20 mm (7.528 inch)Position (C) ... 347.20 mm (13.669 inch)Position (D) ... 503.20 mm (19.811 inch)Position (E) ... 659.20 mm (29.953 inch)Position (F) ... 815.20 mm (32.094 inch)Position (G) ... 954.10 mm (37.563 inch)
Camshaft bearings must be installed in their correct position. Failure to do so will result in engine damage.
View C-C (Camshaft Bearing No. 7)(12) Bearing joint(A) Bearing oil hole at a 45 degree angle
View D-D (Camshaft Bearings No. 2 Through 6)(13) Bearing joint(14) Oil hole
View E-E (Camshaft Bearing No. 1)(15) Bearing joint(16) Oil hole The width of the number 1 through number 6 camshaft bearing is 33.4 0.5 mm (1.32 .02 inch). The width of the number 7 camshaft bearing is 28.0 0.5 mm (1.10 .02 inch). The number 1 camshaft bearing has a 5.0 0.5 mm (.20 .02 inch) wide single groove on the inside diameter of the camshaft bearing. The width of the single groove on the outside diameter of camshaft bearings 2 through 6 is 8.0 0.5 mm (.32 .02 inch). A single groove is on the outside diameter of the number 7 camshaft bearing.