17948-ZV4-000 Honda BRACKET, NEUTRAL START CABLE (Honda Code 2826246).

Table 1
J1939 Code and Description CDL Code and Description Comments
3216-11
Aftertreatment #1 Intake NOx : Other Failure Mode 3655-11
Aftertreatment #1 Intake NOx Level Sensor : Other Failure Mode The #1 intake NOx sensor heater cannot generate enough heat or the power supply is intermittent.
3216-12
Aftertreatment #1 Intake NOx : Failure 3655-12
Aftertreatment #1 Intake NOx Level Sensor : Failure A failed #1 intake NOx sensor has been detected.
3226-11
Aftertreatment #1 Outlet NOx : Other Failure Mode 3609-11
Aftertreatment #1 Outlet #1 NOx Level Sensor : Other Failure Mode The #1 outlet NOx sensor heater cannot generate enough heat or the power supply is intermittent.
3226-12
Aftertreatment #1 Outlet NOx : Failure 3609-12
Aftertreatment #1 Outlet #1 NOx Level Sensor : Failure A failed #1 outlet NOx sensor has been detected.
3360-12
Aftertreatment #1 DEF Controller : Failure 3820-12
Aftertreatment #1 Diesel Exhaust Fluid Controller : Failure The #1 Diesel Exhaust Fluid Controller (DCU) has been flashed or a failed #1 DCU has been detected.
7538-12
Aftertreatment #1 DEF Controller #2 : Failure 4797-12
Aftertreatment #1 Diesel Exhaust Fluid Controller #2 : Failure The #2 DCU has been flashed or a failed #2 DCU has been detected.
7649-11
Aftertreatment #1 SCR Intake NOx #2 : Other Failure Mode 3967-11
Aftertreatment #1 Intake #2 NOx Level Sensor : Other Failure Mode The #2 intake NOx sensor heater cannot generate enough heat or the power supply is intermittent.
7649-12
Aftertreatment #1 SCR Intake NOx #2 : Failure 3967-12
Aftertreatment #1 Intake #2 NOx Level Sensor : Failure A failed #2 intake NOx sensor has been detected.
7660-11
Aftertreatment #1 Outlet NOx #2 : Other Failure Mode 3610-11
Aftertreatment #1 Outlet #2 NOx Level Sensor : Other Failure Mode The #2 outlet NOx sensor heater cannot generate enough heat or the power supply is intermittent.
7660-12
Aftertreatment #1 Outlet NOx #2 : Failure 3610-12
Aftertreatment #1 Outlet #2 NOx Level Sensor : Failure A failed #2 outlet NOx sensor has been detected. Note: Turn the keyswitch to the OFF position before connecting or disconnecting these components.If the Cat® Electronic Technician (ET) will not communicate with the Electronic Control Module (ECM), refer to Troubleshooting, "Electronic Service Tool Does Not Communicate" before you begin this procedure. The procedure verifies that electrical power is being supplied to the ECM and to the service tool connector.The data links are used to communicate information between the engine ECM and other control modules that are a part of the application. Cat ET also communicates with the ECM via the data links.The service tool connector contains connections for electrical power and for the data links.When the keyswitch is in the OFF position, Cat ET may communicate with the ECM. However, the communications may be disrupted and the communications may require frequent reconnection. To avoid this problem, place the keyswitch in the ON position when Cat ET is being used.Cat ET may display the following error message:"The version of the ECM is not recognized and the integrity of the changed parameters and displayed data is not guaranteed."This message indicates that one of the following conditions exist:
The flash file in the ECM is newer than the version of Cat ET.
The latest version of Cat ET has not been installed.
Illustration 1 g06028428
The NOx sensors are on the Clean Emissions Module (CEM).
(1) Inlet 1 NOx sensor
(2) Inlet 2 NOx sensor
(3) Outlet 1 NOx sensor
(4) Outlet 2 NOx sensor
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A -11 code is active or logged.
Proceed to Test Step 2.
Result: A3360-12, 3820-12, 4797-12, or 7538-12 code is active or logged,
Proceed to Test Step 4.
Result: A-12 code other than a 3360-12, 3820-12, 4797-12, or 7538-12 is active or logged.
Repair: Replace the failed NOx sensor. Refer to Special Instruction, REHS8151 for special handling instructions.
Proceed to Test Step 5.
2. Inspect the Electrical Connectors and the Wiring
A. Turn the keyswitch to the OFF position.
B. Thoroughly inspect the connectors. Refer to Troubleshooting, "Electrical Connectors-Inspect" for additional information.
C. Perform a 45 N (10 lb) pull test on the connector wires.
D. Check the harness for abrasions and pinch points.
Connectors and Wiring
Result: The connectors and wiring appear to be OK.
Proceed to Test Step 3.
Result: There is a problem with the connectors and/or wiring.
Repair: Repair or replace the connectors or wiring. Ensure that all the seals are properly in place and ensure that the connectors are coupled.
Note: The Diesel Exhaust Fluid Control Unit (DCU) connector is not serviceable.
If the problem is not resolved, proceed to Test Step 3.
3. Check the Voltage to the Affected Sensor
A. Disconnect the affected sensor from the wiring harness.
B. Turn the keyswitch to the ON position.
C. Measure the voltage on the wiring harness connector between the following:
- +Battery (supply) and -Battery (return)
Battery Voltage
Result: The measured voltage is equal to battery voltage.
Repair: Replace the failed NOx sensor. Refer to Special Instruction, REHS8151 for special handling instructions.
Proceed to Test Step 5.
Result: The measured voltage is not equal to battery voltage.
Repair: There is a problem with an intermittent battery supply. Check the power supply to the affected sensor.
If the problem is not resolved, proceed to Test Step 5.
4. Perform the "DEF Dosing Control Module Reset"
A. Connect Cat ET.
B. Select the "Selective Catalyst Reduction System".
C. Use Cat ET to perform the following diagnostic test:
- DEF Dosing Control Module Key Switch Line Test
Reset
Result: A 3360-12, 3820-12, 4797-12, or 7538-12 code is not active.
Return to service.
Result: A 3360-12, 3820-12, 4797-12, or 7538-12 code is active.
Repair: Replace the DCU.
Proceed to Test Step 5.
5. Perform the "Aftertreatment System Functional Test"
A. Connect Cat ET.
B. Select the "Selective Catalyst Reduction System".
C. Use Cat ET to perform the following diagnostic test:
- "Aftertreatment System Functional Test"
Test
Result: The test was successful.
Return to service.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).