32112-ZV5-000 Honda SEE PART DETAILS - SUP; BRACKET, CABLE CLIP (S) (Honda Code 3703758).

Every attempt is made to provide accurate, up-to-date information. By use of this document, you agree that Caterpillar Inc. is not responsible for errors or omissions. The recommendations provided are the latest recommendations for the Caterpillar 2007 model year On-highway Diesel Engines.
These recommendations are subject to change without prior notice. Contact your Caterpillar dealer for the most up to date recommendations.
For more information on all of the fluids, refer to the latest edition of Special Publication, SEBU6385, "Cat On-highway Diesel Engine Fluids Recommendations".Diesel Engine Oil
Cat Diesel Engine Oil (Cat DEO)
Cat oils have been developed and tested in order to provide the full performance and service life that has been designed and built into Cat engines. Cat oils are currently used to fill Cat Diesel Engines at the factory. These oils are offered by Cat dealers for continued use when the engine oil is changed. Consult your Cat dealer for more information on these oils.Due to significant variations in the quality and in the performance of commercially available oils, Caterpillar makes the following recommendations:
Table 1
Cat Lubricants Viscosity Grade
Diesel Engine Oil-Ultra Low Sulfur Cat DEO-ULS SAE 15W-40
SAE 10W-30
Cat Cold Weather DEO-ULS SAE 0W-40
Diesel Engine Oil Cat DEO SAE 15W-40
SAE 10W-30 Note: Cat DEO-ULS and Cat DEO multigrade oils are the preferred oils for use in this Cat Diesel Engine.Note: The use of Cat DEO-ULS in DPF equipped engines will help maintain the expected DPF performance. Use of oils other than Cat DEO-ULS in DPF equipped engines may cause the need for more frequent DPF cleaning cycles and may contribute to DPF plugging.Commercial Oil
Note: Non-Cat commercial oils are second choice oils for your engine.
Caterpillar does not warrant the quality or performance of non-Cat fluids.
The three current Caterpillar ECF specifications are: Cat ECF-1-a, Cat ECF-2 and Cat ECF-3. Each higher Cat ECF specification provides increased performance over lower Cat ECF specifications.The Caterpillar ECF-3 specification was developed to protect 2007 model year and newer on-highway diesel engines that are designed to use fuels with 15 ppm or less of sulfur. Oils that meet the Caterpillar ECF-3 specification are designed with the following objectives: protection of the emissions control systems, compliance with the emissions standards, reduction of engine wear, reduction of piston deposits and reduction of oil consumption. Oils that meet the API CJ-4 standard are Caterpillar ECF-3 compliant.Oils that have not met the performance requirements of the Caterpillar ECF-3 specification and/or the performance requirements for the API CJ-4 oil category may cause reduced engine life due to deposits, excessive wear, more frequent cleaning of the diesel particulate filter (DPF) and reduced life of the DPF.A commercial oil must meet the following standards to be considered an equivalent of a Cat Diesel Engine Oil:
Table 2
Cat Engine Crankcase Fluids (ECF) Definitions
Cat Performance Requirement Cat ECF Specifications Requirements
Cat ECF-3 API CJ-4 Oil Category performance requirements In selecting oil for any engine application, both of the following must be satisfied: the oil viscosity and the category of oil performance or the specification for oil performance . Using only one of these parameters will not sufficiently define oil for an engine application.The proper SAE viscosity grade of oil is determined by the following temperatures: minimum ambient temperature during cold engine start-up and maximum ambient temperature during engine operation. Refer to Table 3 (minimum temperature) in order to determine the required oil viscosity for starting a cold engine.Refer to Table 3 (maximum temperature) in order to select the oil viscosity for engine operation at the highest ambient temperature that is anticipated.Note: Generally, use the highest oil viscosity that is available to meet the requirement for the temperature at start-up.
Table 3
Lubricant Viscosities for Ambient Temperatures
Oil Type and Performance Requirements Oil Viscosities °C °F
Min Max Min Max
Cat DEO-ULS Cold Weather SAE 0W-40 −40 40 −40 104
Cat DEO-ULS
Cat DEO SAE 10W-30 −18 40 0 104
SAE 15W-40 −10 50 14 122
Commercial Oil ECF-3 SAE 0W-40 −40 40 −40 104
SAE 5W-30 −30 30 −22 86
SAE 0W-30 −40 30 −40 86
SAE 5W-40 −30 50