32520-ZW4-H00 Honda CABLE ASSY., REMOTE CONTROL (Honda Code 7531684). (A)


32520-ZW4-H00 CABLE ASSY., REMOTE CONTROL (Honda Code 7531684). (A) Honda BF40A4 LHA, BF40A5 LHA CABLE
32520-ZW4-H00 CABLE ASSY., REMOTE CONTROL (Honda Code 7531684). (A) Honda
Rating:
8

Buy CABLE ASSY., REMOTE CONTROL (Honda Code 7531684). (A) 32520-ZW4-H00 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

Compatible models:

Honda entire parts catalog list:

BF40A4 LHA 2004
BF40A5 LHA 2005

Information:

Removing And Fitting Cooling Fan
1. Undo the mounting bolt of the generator clamping plate, Fig. 8-1, and remove the V-belt.
8-1 Note for Refitment:The free movement for tensioning the V-belt is about 10 - 15 mm.2. Remove the generator mounting bolt from the cooling fan housing, Fig. 8-2 and remove the generator with the clamping plate.
8-2 Note for Refitment:Note any shims. Correct any misalignment with the V-belt pulley with shims.3. Unscrew the bolts with recessed hexagonal holes and remove the cooling fan.Fig. 8-4
8-4The cooling fan is fitted in reverse order. Note for Refitment:Tighten bolts with recessed hexagonal holes as specified.Dismantling And Reassembling The Cooling Fan
Dismantling
1. Clamp the pulley of the cooling fan in a vice with protective aluminium jaws and unscrew the clamping bolt.Fig. 8-5
8-52. Remove the fan wheel.3. Drive out the drive shaft from the fan housing with a suitable soft metal drift.Fig. 8-6
8-64. Pull the ball bearing from the drive shaft with a bearing puller.Fig. 8-7
8-75. Remove the retaining ring from the ball bearing and drive the ball bearing out of the housing using a suitable soft metal drift.Reassembling:
6. Fill the new bearing with hot-running bearing grease.7. Press the smaller of the two ball bearings into the fan housing with the closed side facing downwards.Fig. 8-8
8-88. Protect the ball bearing against axial movements in the fan housing with the retaining ring.Fig. 8-9
8-99. Press the larger ball bearing over the drive shaft with the closed side facing the V-belt pulley wheel.Fig. 8-10
8-10 Note for Refitment:Only ball bearings with running-play code C 3 should be used.10. Press the fan shaft (with the ball bearing fitted) home into the fan housing.Fig. 8-11
8-1111. Clamp the cooling fan in a vice by the pulley wheel.12. Fit the rotor wheel, Fig. 8-12 and screw in the clamping bolt. Tighten the clamping bolt as specified. For values see Technical Data.
8-12Removing And Fitting The Oil Cooler (F2L 511)
1. Remove the oil line to oil cooler.Fig. 8-13
8-13 Note for Refitment:Use new copper sealing rings.2. Remove air ducting panel.Fig. 8-14
8-143. Remove the oil cooler together with shield.Fig. 8-15
8-15 Note for Refitment:The bolt marked "A" is a banjo bolt. Use new sealing rings to provide a seal.4. Check and/or replace the oil cooler. Check to ensure a seal (acceptable value) 13 bars.The oil cooler is fitted in reverse order.Removing And Fitting Oil Pump
The front cover has been removed.Removal:
1. Remove crankcase cover.Fig. 8-16
8-162. Remove the four bolts of the crankshaft gear wheel and remove the crankshaft gear wheel.Fig. 8-17
8-173. Remove the oil pump mounting bolt.Fig. 8-18
8-184. Twist the oil pump is such a way that it can be removed complete with the intake pipe.Fitting:
5. Fit the oil pump, insert the mounting bolt with a new copper sealing ring and tighten.6. Fit the crankshaft gear wheel. Note for Refitment:Check that the gear wheel markings line up.Fig. 8-19
8-197. Fit the crankcase cover.Checking The Oil Pump For Wear
1. Dismantle and clean the oil pump.2. Check the oil pump cover for wear. The cover must be absolutely flat.Fig. 8-20
8-203. Measure any axial play by means of a measuring square and / or a sliding caliper and feeler gauge.Fig. 8-21For axial play see Technical Data.
8-214. Measure the backlash of the teeth with a feeler gauge.Fig. 8-22For backlash of the teeth see Technical Data.
8-225. Measure the play in the gear wheels in the housing with the feeler gauge, Fig. 8-23 and compare with the values in the Technical Data.
8-236. Fit the oil pump cover. Tighten the bolts.


Parts cable Honda:

32580-ZY3-000
CABLE ASSY., SWITCH PANEL (Honda Code 6991772).
32580-ZY3-000 CABLE ASSY., SWITCH PANEL (Honda Code 6991772).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
17910-ZW4-H01
CABLE, THROTTLE (Honda Code 7744089).
17910-ZW4-H01 CABLE, THROTTLE (Honda Code 7744089).
BF25D4 LHA, BF25D4 LHTA, BF25D4 LRGA, BF25D4 LRTA, BF25D4 SHA, BF25D4 SHGA, BF25D4 SRGA, BF25D4 SRTA, BF25D5 LHA, BF25D5 LHTA, BF25D5 LRGA, BF25D5 LRTA, BF25D5 SHA, BF25D5 SHGA, BF25D5 SRGA, BF25D5 SRTA, BF25D6 LHA, BF25D6 LHTA, BF25D6 LRGA, BF25D6 L
24590-ZW4-H01
CABLE, SHIFT (Honda Code 7744105).
24590-ZW4-H01 CABLE, SHIFT (Honda Code 7744105).
BF25D4 LHA, BF25D4 LHTA, BF25D4 LRGA, BF25D4 LRTA, BF25D4 SHA, BF25D4 SHGA, BF25D4 SRGA, BF25D4 SRTA, BF25D5 LHA, BF25D5 LHTA, BF25D5 LRGA, BF25D5 LRTA, BF25D5 SHA, BF25D5 SHGA, BF25D5 SRGA, BF25D5 SRTA, BF25D6 LHA, BF25D6 LHTA, BF25D6 LRGA, BF25D6 L
32538-ZW4-H01
CABLE ASSY., LONG HANDLE (A) (Honda Code 7785629).
32538-ZW4-H01 CABLE ASSY., LONG HANDLE (A) (Honda Code 7785629).
BF40A4 LHA, BF40A4 LHTA, BF40A4 LRTA, BF40A5 LHA, BF40A5 LHTA, BF40A5 LRTA, BF40A6 LHA, BF40A6 LHTA, BF40A6 LRTA, BF40AK0 LHA, BF40AK0 LRTA, BF50A4 LHTA, BF50A4 LRTA, BF50A4 SRJA, BF50A4 XRTA, BF50A5 LHTA, BF50A5 LRTA, BF50A5 SRJA, BF50A5 XRTA, BF50A
32410-ZW4-H00
 
32410-ZW4-H00 CABLE ASSY., STARTER (Honda Code 7531676).
BF40A4 LHA, BF40A5 LHA, BF40A6 LHA, BF40AK0 LHA
Back to top