14111-ZY3-000 Honda CAMSHAFT, R. (Honda Code 6989453).


14111-ZY3-000 CAMSHAFT, R. (Honda Code 6989453). Honda BF200A2 LA, BF200A2 XA, BF200A2 XCA, BF200A2 XXA, BF200A2 XXCA, BF200A3 LA, BF200A3 XA, BF200A3 XCA, BF200A3 XXA, BF200A3 XXCA, BF200A4 LA, BF200A4 XA, BF200A4 XCA, BF200A4 XXA, BF200A4 XXCA, BF200A5 LA, BF200A5 XA, BF200A5 XCA, BF200A5 XXA, BF200A5 CAMSHAFT
14111-ZY3-000 CAMSHAFT, R. (Honda Code 6989453). Honda
Rating:
28

Buy CAMSHAFT, R. (Honda Code 6989453). 14111-ZY3-000 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Honda entire parts catalog list:

BF200A2 LA 2002
BF200A2 XA 2002
BF200A2 XCA 2002
BF200A2 XXA 2002
BF200A2 XXCA 2002
BF200A3 LA 2003
BF200A3 XA 2003
BF200A3 XCA 2003
BF200A3 XXA 2003
BF200A3 XXCA 2003
BF200A4 LA 2004
BF200A4 XA 2004
BF200A4 XCA 2004
BF200A4 XXA 2004
BF200A4 XXCA 2004
BF200A5 LA 2005
BF200A5 XA 2005
BF200A5 XCA 2005
BF200A5 XXA 2005
BF200A5 XXCA 2005
BF225A2 LA 2002
BF225A2 XA 2002
BF225A2 XCA 2002
BF225A2 XXA 2002
BF225A2 XXCA 2002
BF225A3 LA 2003
BF225A3 XA 2003
BF225A3 XCA 2003
BF225A3 XXA 2003
BF225A3 XXCA 2003
BF225A4 LA 2004
BF225A4 XA 2004
BF225A4 XCA 2004
BF225A4 XXA 2004
BF225A4 XXCA 2004
BF225A5 LA 2005
BF225A5 XA 2005
BF225A5 XCA 2005
BF225A5 XXA 2005
BF225A5 XXCA 2005

Information:


Table 1
J1939 Code and Description CDL Code and Description System Response
101-0
Engine Crankcase Pressure : High - most severe (3) E101 (3)
High Crankcase Pressure Warning The engine crankcase pressure is higher than a threshold.
101-15
Engine Crankcase Pressure : High - least severe (1) E101 (1)
High Crankcase Pressure Warning The engine crankcase pressure is higher than a threshold.
101-16
Engine Crankcase Pressure : High - moderate severity (2) E101 (2)
High Crankcase Pressure Warning The engine crankcase pressure is higher than a threshold. Probable Causes
Engine oil
Plugged CCV system
Clogged CCV filter
Sensor
Engine componentsRecommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Table 2
Troubleshooting Test Steps Values Results
1. Check the Engine Oil Level
Oil Level
Result: The engine oil level is OK.
Proceed to Test Step 2.
Result: The engine oil level is high.
Repair: Troubleshoot and repair the cause of the incorrect oil level.
If the problem is not resolved, proceed to Test Step 2.
2. Check for Plugged CCV System or Clogged Filters
A plugged CCV system or clogged filter will cause excessive crankcase pressure.
Plugged Crankcase Breather
Result: The crankcase breathers are NOT OK.
Repair: Replace the fumes disposal filter according to the Operation and Maintenance Manual, "Engine Crankcase Breather - Clean".
Result: The crankcase breathers are OK.
Proceed to Test Step 3.
3. Check for a Faulty Pressure Sensor
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Turn the keyswitch to the ON position. Do not start the engine.
C. Remove the oil filler cap.
D. Monitor the crankcase pressure and the atmospheric pressure in Cat ET.
Crankcase Pressure Sensor
Result: The crankcase pressure is within 3.5 kPa (0.5 psi) of the atmospheric pressure.
Proceed to Test Step 4.
Result: The crankcase pressure is not within 3.5 kPa (0.5 psi) of the atmospheric pressure.
Repair: Replace the crankcase pressure sensor.
If the problem is not resolved, proceed to Test Step 4.
4. Internal Engine Problem
Damaged pistons or rings can cause too much pressure in the crankcase. This condition will cause the engine to run rough. There will be more than the normal quantity of fumes (blowby) entering the crankcase breathers. The crankcase breathers can then more quickly become restricted, causing oil leakage at gaskets and seals that would not normally have leakage. Blowby can also be caused by worn valve guides or by a failed turbocharger seal.
A. To determine whether the piston rings leak, measure the crankcase blowby.
B. Perform the Compression Test using Cat ET. Refer to Testing and Adjusting, "Compression - Test" for additional information.
Damaged or Worn Engine Parts
Result: There are worn or damaged engine parts.
Repair: Repair or replace the worn or damaged parts.
Result: At least one cylinder has been identified as having low compression.
Repair: Identify the cause of the low compression. Possible causes of low compression include the following:
- Faulty piston
- Faulty piston rings
- Worn cylinder bores
- Worn valves
- Faulty cylinder head gasket
- Damaged cylinder head
Perform the necessary repairs.
Result: The compression for each cylinder is OK.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts camshaft Honda:

14211-ZY3-000
 
14211-ZY3-000 CAMSHAFT, L. (Honda Code 6989461).
BF200A2 LA, BF200A2 XA, BF200A2 XCA, BF200A2 XXA, BF200A2 XXCA, BF200A3 LA, BF200A3 XA, BF200A3 XCA, BF200A3 XXA, BF200A3 XXCA, BF200A4 LA, BF200A4 XA, BF200A4 XCA, BF200A4 XXA, BF200A4 XXCA, BF200A5 LA, BF200A5 XA, BF200A5 XCA, BF200A5 XXA, BF200A5
Back to top