40201-ZV5-010ZA Honda CASE, EXTENSION *NH282MU* (S) (Honda Code 7091747). (OYSTER SILVER METALLIC-U)


40201-ZV5-010ZA CASE, EXTENSION *NH282MU* (S) (Honda Code 7091747). (OYSTER SILVER METALLIC-U) Honda BF35AM SHA, BF45AM SRTA, BF50A1 SRJA, BF50A2 SRJA, BF50A3 SRJA, BF50A4 SRJA, BF50A5 SRJA, BF50A6 SRJA, BF50AK0 LRTA, BF50AK0 SRJA, BF50AK0 XRTA, BF50AW SRJA, BF50AX SRJA, BF50AY SRJA CASE
40201-ZV5-010ZA CASE, EXTENSION *NH282MU* (S) (Honda Code 7091747). (OYSTER SILVER METALLIC-U) Honda
Rating:
98

Buy CASE, EXTENSION *NH282MU* (S) (Honda Code 7091747). (OYSTER SILVER METALLIC-U) 40201-ZV5-010ZA Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Honda entire parts catalog list:

BF35AM SHA 1997
BF45AM SRTA 1997
BF50A1 SRJA 2001
BF50A2 SRJA 2002
BF50A3 SRJA 2003
BF50A4 SRJA 2004
BF50A5 SRJA 2005
BF50A6 SRJA 2006
BF50AK0 LRTA 2007
BF50AK0 SRJA 2007
BF50AK0 XRTA 2007
BF50AW SRJA 1998
BF50AX SRJA 1999
BF50AY SRJA 2000

Information:


Table 1
J1939 Code CDL Code Code Description Comments
1639-17 E1363 (1) Low Engine Cooling Fan Speed The code is logged.
N/A 544-2 Engine Cooling Fan Speed Sensor : Erratic, Intermittent, or Incorrect The code is logged.
N/A 544-8 Engine Cooling Fan Speed Sensor : Abnormal Frequency, Pulse Width, or Period The code is logged. The engine cooling fan speed sensor provides a signal to the Electronic Control Module (ECM). The ECM controls fan speed by varying the current to the fan control solenoid.The engine cooling fan speed sensor receives a supply voltage of 5.0 0.5 VDC from the ECM. The sensor outputs a frequency that is directly proportional to fan speed. The sensor generates a signal pulse for each revolution of the fan. The output frequency varies between 5 Hz to 180 Hz over the speed range between 50 rpm and 1800 rpm.Recommended Actions
Table 2
Troubleshooting Test Steps Values Results
1. Check the Status of the Engine Fan Speed
A. Turn the keyswitch to OFF.
B. Connect Cat® Electronic Technician (ET) to the service tool connector.
C. Turn the keyswitch to ON.
D. Access the "Fan Override Test" under the "Diagnostics" menu.
E. Start the "Fan Override Test" on Cat ET. Set the fan speed to 800 rpm.
F. Use a 351-8635 Tachometer Kit to determine the actual speed of the fan.
G. Compare the engine fan speed that is reported by Cat ET to the actual engine fan speed that is reported by the photo-tachometer.
H. Deactivate the "Fan Override Test".
I. Turn the keyswitch to OFF.
Fan Speed
Result: The engine fan speed is within 50 rpm.
The sensor is operating correctly. There may be an intermittent electrical problem in a connector or in the harness. If an intermittent problem is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect".
Result: The engine fan speed is not within 50 rpm.
Proceed to Test Step 2.
2. Check the Sensor Supply Voltage at the Sensor Connector
A. Turn the keyswitch to OFF.
B. Disconnect the sensor connector from the wiring harness.
C. Turn the keyswitch to ON.
D. Measure the voltage between the fan speed sensor supply pin and the ground pin.
Note: Some fan speed sensors use a 5V power supply and some use an 8V power supply. Refer to the appropriate schematic for the correct pins.
Supply Voltage
Result: The supply voltage is reaching the sensor.
Proceed to Test Step 3.
Result: The supply voltage is not reaching the sensor.
Repair: Refer to Troubleshooting, "Sensor Supply - Test".
3. Check the Signal Frequency at the Sensor Connector
A. Turn the keyswitch to OFF.
B. Remove the wire from terminal 1 on the sensor side of the connector. Connect the sensor connector.
C. Turn the keyswitch to ON.
D. Access the "Fan Override Test" under the "Diagnostics" menu on Cat ET.
E. Start the "Fan Override Test" on Cat ET. Set the fan speed to 800 rpm.
F. Use a multimeter to measure the frequency between the signal wire from the sensor and engine ground.
G. Deactivate the "Fan Override Test".
H. Turn the keyswitch to OFF.
I. Restore all connectors and wiring to the original configuration.
Sensor Frequency
Result: The frequency is approximately 80 Hz.
Note: Large Hydraulic Excavators use a frequency of 27Hz
The engine cooling fan speed sensor is generating the correct signal.
Repair: Repair the harness or replace the harness.
Verify that the problem is resolved.
Note: Large Hydraulic Excavators use a frequency of 27Hz
Result: The frequency is not approximately 80 Hz.
Repair: Replace the fan drive assembly.
Verify that the problem is resolved.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solution Network (DSN).


Parts case Honda:

40101-ZV5-000ZA
 
40101-ZV5-000ZA CASE, ENGINE (LOWER) *NH282MU* (Honda Code 3704335). (OYSTER SILVER METALLIC-U)
BF35AM LHA, BF35AM LRA, BF35AM LRTA, BF35AM SHA, BF35AM XRTA, BF40A1 LHA, BF40A1 LHTA, BF40A1 LRA, BF40A1 LRTA, BF40A1 XRTA, BF40A2 LHA, BF40A2 LHTA, BF40A2 LRA, BF40A2 LRTA, BF40A2 XRTA, BF40A3 LHA, BF40A3 LHTA, BF40A3 LRA, BF40A3 LRTA, BF40A3 XRTA,
40151-ZV5-000ZA
CASE, SEPARATE *NH282MU* (Honda Code 3704483). (OYSTER SILVER METALLIC-U)
40151-ZV5-000ZA CASE, SEPARATE *NH282MU* (Honda Code 3704483). (OYSTER SILVER METALLIC-U)
BF35AM LHA, BF35AM LRA, BF35AM LRTA, BF35AM SHA, BF35AM XRTA, BF40A1 LHA, BF40A1 LHTA, BF40A1 LRA, BF40A1 LRTA, BF40A1 XRTA, BF40A2 LHA, BF40A2 LHTA, BF40A2 LRA, BF40A2 LRTA, BF40A2 XRTA, BF40A3 LHA, BF40A3 LHTA, BF40A3 LRA, BF40A3 LRTA, BF40A3 XRTA,
40201-ZV5-701ZA
 
40201-ZV5-701ZA CASE, EXTENSION *NH282MU* (L) (Honda Code 7226087). (OYSTER SILVER METALLIC-U)
BF35AM LHA, BF35AM LRA, BF35AM LRTA, BF35AM XRTA, BF40A1 LHA, BF40A1 LHTA, BF40A1 LRA, BF40A1 LRTA, BF40A1 XRTA, BF40A2 LHA, BF40A2 LHTA, BF40A2 LRA, BF40A2 LRTA, BF40A2 XRTA, BF40A3 LHA, BF40A3 LHTA, BF40A3 LRA, BF40A3 LRTA, BF40A3 XRTA, BF40A4 LHA,
30587-ZV5-003
CASE, IGNITION CONTROL MODULE (Honda Code 3703485).
30587-ZV5-003 CASE, IGNITION CONTROL MODULE (Honda Code 3703485).
BF25A1 LHA, BF25A1 LHSA, BF25A1 LRSA, BF25A1 SHA, BF25A1 SHSA, BF25A1 SRSA, BF25A1 XRSA, BF25A2 LHA, BF25A2 LHSA, BF25A2 LRSA, BF25A2 SHA, BF25A2 SHSA, BF25A2 SRSA, BF25A2 XRSA, BF25A3 LHA, BF25A3 LHSA, BF25A3 LRSA, BF25A3 SHA, BF25A3 SHSA, BF25A3 SR
50201-ZV5-020ZA
CASE, SWIVEL *NH282MU* (Honda Code 6649453). (OYSTER SILVER METALLIC-U)
50201-ZV5-020ZA CASE, SWIVEL *NH282MU* (Honda Code 6649453). (OYSTER SILVER METALLIC-U)
BF35AM LHA, BF35AM LRA, BF35AM LRTA, BF35AM SHA, BF35AM XRTA, BF40A1 LHA, BF40A1 LHTA, BF40A1 LRA, BF40A1 LRTA, BF40A1 XRTA, BF40A2 LHA, BF40A2 LHTA, BF40A2 LRA, BF40A2 LRTA, BF40A2 XRTA, BF40A3 LHA, BF40A3 LHTA, BF40A3 LRA, BF40A3 LRTA, BF40A3 XRTA,
41100-ZW4-H96ZA
 
41100-ZW4-H96ZA CASE ASSY., GEAR *NH282MU* (UL-TYPE) (OYSTER SILVER METALLIC-U)
BF40A1 LHA, BF40A1 LHTA, BF40A1 LRA, BF40A1 LRTA, BF40A1 XRTA, BF40A2 LHA, BF40A2 LHTA, BF40A2 LRA, BF40A2 LRTA, BF40A2 XRTA, BF40A3 LHA, BF40A3 LHTA, BF40A3 LRA, BF40A3 LRTA, BF40A3 XRTA, BF40AY LHA, BF40AY LHTA, BF40AY LRA, BF40AY LRTA, BF40AY XRTA
04231-ZV5-000ZA
CASE KIT, PRIMARY GEAR *NH8* (DARK GRAY)
04231-ZV5-000ZA CASE KIT, PRIMARY GEAR *NH8* (DARK GRAY)
BF40A1 LHA, BF40A1 LHTA, BF40A1 LRA, BF40A1 LRTA, BF40A1 XRTA, BF40A2 LHA, BF40A2 LHTA, BF40A2 LRA, BF40A2 LRTA, BF40A2 XRTA, BF40A3 LHA, BF40A3 LHTA, BF40A3 LRA, BF40A3 LRTA, BF40A3 XRTA, BF40A4 LHA, BF40A4 LHTA, BF40A4 LRTA, BF40A5 LHA, BF40A5 LHTA
41101-ZW4-H01ZA
 
41101-ZW4-H01ZA CASE, GEAR *NH282MU* (Honda Code 7968548). (OYSTER SILVER METALLIC-U)
BF40A4 LHA, BF40A4 LHTA, BF40A4 LRTA, BF40A5 LHA, BF40A5 LHTA, BF40A5 LRTA, BF40A6 LHA, BF40A6 LHTA, BF40A6 LRTA, BF40AK0 LHA, BF40AK0 LRTA, BF50A4 LHTA, BF50A4 LRTA, BF50A4 XRTA, BF50A5 LHTA, BF50A5 LRTA, BF50A5 XRTA, BF50A6 LHTA, BF50A6 LRTA, BF50A
Back to top