41005-881-000ZA Honda CASE ASSY., GEAR *NH282MU* (Honda Code 6007330). (S-TYPE) (OYSTER SILVER METALLIC-U)


41005-881-000ZA CASE ASSY., GEAR *NH282MU* (Honda Code 6007330). (S-TYPE) (OYSTER SILVER METALLIC-U) Honda BF8A3 SA, BF8A4 SA, BF8A5 SA, BF8A6 SA, BF8AK0 SA, BF8AM SA, BF8AW SA, BF8AX SA, BF8AY SA CASE
41005-881-000ZA CASE ASSY., GEAR *NH282MU* (Honda Code 6007330). (S-TYPE) (OYSTER SILVER METALLIC-U) Honda
Rating:
88

Buy CASE ASSY., GEAR *NH282MU* (Honda Code 6007330). (S-TYPE) (OYSTER SILVER METALLIC-U) 41005-881-000ZA Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Honda entire parts catalog list:

BF8A3 SA 2003
BF8A4 SA 2004
BF8A5 SA 2005
BF8A6 SA 2006
BF8AK0 SA 2007
BF8AM SA 1997
BF8AW SA 1998
BF8AX SA 1999
BF8AY SA 2000

Information:


Table 1
Engine Event
J1939 Code and Description Conditions that Generate the Code System Response
100-1 Engine Oil Pressure : Low - most severe (3) Oil pressure is below the specified pressure for at least eight seconds. A snapshot is triggered. The code is logged. Engine performance is not affected. The code is logged.
100-17 Engine Oil Pressure : Low - least severe (1) Oil pressure is lower than the specified pressure for at least four seconds. Engine power is reduced. A snapshot is triggered. The code is logged. Factory passwords are required.
100-18 Engine Oil Pressure : Low - moderate severity (2) Probable Causes
Engine Oil Level
Low engine oil levelAerated Oil
Aeration in the oilOil Viscosity
Low oil viscosityOil Filter
Plugged Oil FilterOil Pump
Faulty oil pumpEngine Oil Pressure Sensor
Faulty engine oil pressure sensorEngine Oil Filter Bypass Valve
Faulty bypass valveOil Pump Suction Tube
Damaged suction tube or cracked suction tubeWorn Engine Components
Excessive wear of engine componentsTroubleshooting Sequence
Note: Complete the following procedures in the order that is provided.
Engine Oil Level
Check the engine oil level in the crankcase. Refer to the Operation and Maintenance Manual for calibration of the dipstick gauge. The oil level can possibly be too far below the oil pump supply tube. There will not be enough oil and the oil pump will not supply enough lubrication to the engine components.
If the engine oil level is low, add engine oil in order to obtain the correct level. Refer to Operation and Maintenance Manual, "Engine Oil" for the recommendations of engine oil.
If the problem has been corrected, return the unit to service.
If the symptom remains, proceed to the next Test Step.
Aerated Oil
Sample the engine oil for aeration.
If the oil is aerated, proceed to Test Step 8.
If the symptom remains, proceed to the next Test Step.
Oil Viscosity
Sample the engine oil viscosity.
If the oil viscosity is not correct, replace the engine oil. Refer to Operation and Maintenance Manual, "Engine Oil" for the recommendations of engine oil. If the symptom is corrected, return the unit to service. If the symptom still exists, proceed to the next Test Step.
If the oil viscosity is correct, proceed to the next Test Step. Refer to Operation and Maintenance Manual, "Engine Oil" for the recommendations of engine oil.
Oil Filter
Replace the engine oil filter.
If the symptom is corrected, return the unit to service.
If the symptom remains, proceed to the next Test Step.
Oil Pump
Manually check the engine oil pressure. Refer to Testing and Adjusting, "Engine Oil Pressure - Test" for the correct procedure.
If the pressure at the test port is correct, proceed to the next Test Step.
If the pressure does not meet the specifications, replace the pump.
If the symptom is corrected, return the unit to service.
If the symptom remains, proceed to the next Test Step.
Engine Oil Pressure Sensor
Remove the oil pressure sensor.
Install a tee fitting at the port for the pressure sensor.
Install a manual gauge on one side of the tee fitting and install the oil pressure sensor on the other side of the tee fitting.
Start the engine and compare the two readings. The pressure reading must be within 13.8 kPa ( 2 psi).
If the pressure is within 13.8 kPa ( 2 psi), proceed to the next Test Step.
If the pressure is not within 13.8 kPa ( 2 psi), replace the sensor.
If the symptom is corrected, return the unit to service.
If the symptom remains, proceed to the next Test Step.
Engine Oil Filter Bypass Valve
Replace the oil filter base.
If the symptom is corrected, return the unit to service.
If the symptom remains, proceed to the next Test Step.
Oil Pump Suction Tube
Remove the oil pan.
Inspect the suction tube. Check the joints of the tube for cracks or for a damaged O-ring seal at the connection to the pump.
Inspect the inlet screen of the suction tube for a restriction. This restriction will cause cavitation and a loss of engine oil pressure.
Replace parts, if necessary.
If the symptom is corrected, return the unit to service.
If the symptom remains, proceed to the next Test Step.
Worn Engine Components
Remove the valve covers.
Inspect the camshaft and bearings.
Remove the oil pan.
Excessive clearance at the crankshaft or camshaft bearings will cause low engine oil pressure. Check the engine components for excessive clearance. Also, inspect the piston cooling jets.
Replace parts, if necessary. Check the Reuse and Salvage Guidelines for the reusability of existing engine components.


Parts case Honda:

11301-881-020ZA
 
11301-881-020ZA CASE, STARTER *NH8* (DARK GRAY) (Honda Code 3753324).
BF8A3 LA, BF8A3 SA, BF8A4 LA, BF8A4 SA, BF8A5 LA, BF8A5 SA, BF8A6 LA, BF8A6 SA, BF8AK0 LA, BF8AK0 SA, BF8AM LA, BF8AM SA, BF8AM XA, BF8AW LA, BF8AW SA, BF8AW XA, BF8AX LA, BF8AX SA, BF8AX XA, BF8AY LA, BF8AY SA, BF8AY XA
41100-881-A00ZB
 
41100-881-A00ZB CASE, GEAR *NH282MU* (Honda Code 3746765). (OYSTER SILVER METALLIC-U)
BF8A3 LA, BF8A3 SA, BF8A4 LA, BF8A4 SA, BF8A5 LA, BF8A5 SA, BF8A6 LA, BF8A6 SA, BF8AK0 LA, BF8AK0 SA, BF8AM LA, BF8AM SA, BF8AM XA, BF8AW LA, BF8AW SA, BF8AW XA, BF8AX LA, BF8AX SA, BF8AX XA, BF8AY LA, BF8AY SA, BF8AY XA
50200-881-844ZB
CASE ASSY., SWIVEL *NH282MU* (Honda Code 7353162). (OYSTER SILVER METALLIC-U)
50200-881-844ZB CASE ASSY., SWIVEL *NH282MU* (Honda Code 7353162). (OYSTER SILVER METALLIC-U)
BF8A3 LA, BF8A3 SA, BF8A4 LA, BF8A4 SA, BF8A5 LA, BF8A5 SA, BF8A6 LA, BF8A6 SA, BF8AK0 LA, BF8AK0 SA, BF8AM LA, BF8AM SA, BF8AM XA, BF8AW LA, BF8AW SA, BF8AW XA, BF8AX LA, BF8AX SA, BF8AX XA, BF8AY LA, BF8AY SA, BF8AY XA
28401-881-016
 
28401-881-016 CASE, RECOIL STARTER (Honda Code 4582730).
BF8A3 LA, BF8A3 SA, BF8A4 LA, BF8A4 SA, BF8A5 LA, BF8A5 SA, BF8A6 LA, BF8A6 SA, BF8AK0 LA, BF8AK0 SA, BF8AM LA, BF8AM SA, BF8AM XA, BF8AW LA, BF8AW SA, BF8AW XA, BF8AX LA, BF8AX SA, BF8AX XA, BF8AY LA, BF8AY SA, BF8AY XA
40201-881-842ZB
 
40201-881-842ZB CASE, EXTENSION *NH282MU* (S) (Honda Code 3746724). (OYSTER SILVER METALLIC-U)
BF8A3 SA, BF8A4 SA, BF8A5 SA, BF8A6 SA, BF8AK0 SA, BF8AM SA, BF8AW SA, BF8AX SA, BF8AY SA
28401-881-016ZA
 
28401-881-016ZA CASE, RECOIL STARTER *NH8* (Honda Code 2920908). (DARK GRAY)
BF8AX LA, BF8AX SA, BF8AX XA, BF8AY LA, BF8AY SA, BF8AY XA
Back to top