12328-ZZ5-000 CLAMP, TUBE Honda
BF40DK2 LHA, BF40DK2 LRTA, BF50DK2 LRTA, BF50DK2 XRTA
CLAMP
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Compatible models:
Honda entire parts catalog list:
- TIMING BELT » 12328-ZZ5-000
- TIMING BELT » 12328-ZZ5-000
- TIMING BELT » 12328-ZZ5-000
- TIMING BELT » 12328-ZZ5-000
Information:
Start By: a. remove oil pump1. Check the identification marks on the connecting rods and caps as to their location in the engine. The caps must be installed in original positions in the engine.2. Turn the crankshaft until two of the pistons are at bottom center. 3. Remove conecting rod caps (1) from the connecting rods. Remove the lower half of the bearings from the caps.
Be careful not to damage the crankshaft journals. Do not turn the crankshaft while any of the connecting rod caps are removed.
4. Push the connecting rod away from the crankshaft, and remove the upper half of the bearings from the connecting rods.5. Make sure the surface of the connecting rod where the bearings make contact is clean and free of dirt.
Make sure the tabs on the bearings are in alignment with the notches in the connecting rods and caps.
6. Install the upper half of new bearings in the connecting rods.7. Pull the connecting rod down slowly on the crankshaft.
Make sure the surfaces where the bearings make contact in the caps are clean and free of dirt.
8. Install new bearings (2) in the caps. Make sure the tabs on the bearings are in alignment with the notches in the caps.The serviceman must be very careful to use Plastigage, tool (B) correctly. The following points must be remembered: ... Make sure that the backs of the bearings and the bores are clean and dry.... Make sure that the bearing locking tabs are properly seated in their slots.... The crankshaft must be free of oil where the Plastigage touches it.... Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.... Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.... Do not turn the crankshaft with the Plastigage installed.... Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.... Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004") the readings may be low by 0.013 to 0.025 mm (.0005 to .0010"). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider that the other.For complete details concerning measuring bearing clearances, see Engine Bearings And Crankshafts, Form No. SEBD0531.9. Put 2P2506 Thread Lubricant on the threads of the bolts in the connecting rods.10 Check the bearing clearance with Plastigage (A) as follows:
When Plastigage is used to check bearing clearance, do not use an impact wrench for the torque tightening sequence. However, an impact wrench can be used for the final tightening torque.
a. Make sure the numbers on the caps and connecting rods are the same and are on the same respective side. If new connecting rods are installed. Put the cylinder number on the rods and caps. b. Put caps (1) and Plastigage (A) in the correct position on the connecting rods. Install the nuts that hold them. c. Tighten the two nuts evenly to a torque of 80 8 N m (60 6 lb.ft.). Put a mark on each nut, and tighten the nuts 120° 5° more from the marks.d. Remove the caps from the connecting rods and Plastigage (A). Measure the thickness of the Plastigage (A). The connecting rod bearing clearance must be 0.071 to 0.168 mm (.0028 to .0066 in.) for new bearings and maximum permissible distance for worn bearings 0.25 mm (.010 in.).e. Put clean engine oil in the bearing caps, and install them again. Follow the tightening procedure in Step 10c.f. Do Steps 1 through 10 for the other connecting rod bearings.End By: a. install oil pump
Be careful not to damage the crankshaft journals. Do not turn the crankshaft while any of the connecting rod caps are removed.
4. Push the connecting rod away from the crankshaft, and remove the upper half of the bearings from the connecting rods.5. Make sure the surface of the connecting rod where the bearings make contact is clean and free of dirt.
Make sure the tabs on the bearings are in alignment with the notches in the connecting rods and caps.
6. Install the upper half of new bearings in the connecting rods.7. Pull the connecting rod down slowly on the crankshaft.
Make sure the surfaces where the bearings make contact in the caps are clean and free of dirt.
8. Install new bearings (2) in the caps. Make sure the tabs on the bearings are in alignment with the notches in the caps.The serviceman must be very careful to use Plastigage, tool (B) correctly. The following points must be remembered: ... Make sure that the backs of the bearings and the bores are clean and dry.... Make sure that the bearing locking tabs are properly seated in their slots.... The crankshaft must be free of oil where the Plastigage touches it.... Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.... Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.... Do not turn the crankshaft with the Plastigage installed.... Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.... Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004") the readings may be low by 0.013 to 0.025 mm (.0005 to .0010"). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider that the other.For complete details concerning measuring bearing clearances, see Engine Bearings And Crankshafts, Form No. SEBD0531.9. Put 2P2506 Thread Lubricant on the threads of the bolts in the connecting rods.10 Check the bearing clearance with Plastigage (A) as follows:
When Plastigage is used to check bearing clearance, do not use an impact wrench for the torque tightening sequence. However, an impact wrench can be used for the final tightening torque.
a. Make sure the numbers on the caps and connecting rods are the same and are on the same respective side. If new connecting rods are installed. Put the cylinder number on the rods and caps. b. Put caps (1) and Plastigage (A) in the correct position on the connecting rods. Install the nuts that hold them. c. Tighten the two nuts evenly to a torque of 80 8 N m (60 6 lb.ft.). Put a mark on each nut, and tighten the nuts 120° 5° more from the marks.d. Remove the caps from the connecting rods and Plastigage (A). Measure the thickness of the Plastigage (A). The connecting rod bearing clearance must be 0.071 to 0.168 mm (.0028 to .0066 in.) for new bearings and maximum permissible distance for worn bearings 0.25 mm (.010 in.).e. Put clean engine oil in the bearing caps, and install them again. Follow the tightening procedure in Step 10c.f. Do Steps 1 through 10 for the other connecting rod bearings.End By: a. install oil pump
Parts clamp Honda:
32660-MJ6-710
32660-MJ6-710 CLAMP, WIRE (Honda Code 3703907).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
24818-ZV5-003
24818-ZV5-003 CLAMP, HARNESS (Honda Code 3703113).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
37215-KM1-670
37215-KM1-670 CLAMP (Honda Code 2047215).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
17439-PY3-A01
17439-PY3-A01 CLAMP, TUBE (7.5-11.5) (BLACK) (Honda Code 3684628).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
90601-ZV3-030
90601-ZV3-030 CLAMP, TUBE (D17)
BF115DK1 LA, BF115DK1 XA, BF115DK1 XCA, BF135A4 LA, BF135A4 XA, BF135A4 XCA, BF135A5 LA, BF135A5 XA, BF135A5 XCA, BF135A6 LA, BF135A6 XA, BF135A6 XCA, BF135AK0 LA, BF135AK0 XA, BF135AK0 XCA, BF135AK2 LA, BF135AK2 XA, BF135AK2 XCA, BF150A4 LA, BF150A4
16897-ZW9-003
16897-ZW9-003 CLAMP, FUEL TUBE
BF115DK1 LA, BF115DK1 XA, BF115DK1 XCA, BF135AK2 LA, BF135AK2 XA, BF135AK2 XCA, BF150AK2 LA, BF150AK2 XA, BF150AK2 XCA, BF15DK2 LHA, BF15DK2 LHSA, BF15DK2 LHTA, BF15DK2 LRTA, BF15DK2 SHA, BF15DK2 SHSA, BF15DK2 SHTA, BF15DK3 LHA, BF15DK3 LHSA, BF15DK3
53123-ZW4-H01
53123-ZW4-H01 CLAMP, BRACKET
BF25DK0 LRGA, BF25DK0 LRTA, BF25DK0 SHGA, BF25DK2 LRGA, BF25DK2 LRTA, BF25DK2 SHGA, BF25DK3 LRGA, BF25DK3 LRTA, BF25DK3 SHGA, BF30DK0 LRGA, BF30DK0 LRTA, BF30DK0 SRTA, BF30DK2 LRGA, BF30DK2 LRTA, BF30DK2 SRTA, BF30DK3 LRGA, BF30DK3 LRTA, BF30DK3 SRTA
16895-ZZ5-003