90689-SB0-013 Honda CLIP, SEAL RUBBER (Honda Code 1904507).

} } @media print { div.divFooter { position: fixed; bottom: 0; right: 0; } } Caterpillar: Confidential Yellow
SAFETY - INSTALL PARTS ON ICM TRANSMISSIONS TO PREVENT STARTING ENGINE WITH TRANSMISSION LEVER IN GEAR - 651E, 657E, 768 C, 772B, 776, 769C, 773B, 777 - PI1034 - WORLDWIDE EXCEPT BRAZIL
  The information supplied in this service letter may not be valid after the termination date of this program.   Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.
INSTALL PARTS ON ICM TRANSMISSIONS TO PREVENT STARTING ENGINE WITH TRANSMISSION LEVER IN GEAR, 651E, 657E, 768C, 772B, 776 Tractors; 769C, 773B, 777 Trucks, 3167, 3168, 1424, PI1034 U-2 A-1 AU-1 C-1 E-2 O-1 safety Problem Effective with the first serial numbers listed in the Chart, each model is equipped with the ICM (Individual Clutch Modulated) transmission. It is possible that the engine in any of the listed machines can be started with the transmission selector lever "in gear". This could cause the vehicle to move unexpectedly. A neutral start switch is now used to prevent the starter from cranking if the transmission is left in gear. Affected Machines And Parts Needed Model Serial Numbers 651E Tractor 89Z1-89Z95, 98 657E Tractor 90Z1-90Z117, 120 657E Tractor 91Z1-91Z205 768C Tractor 2X350-2X355 772B Tractor 64W168-64W170 776 Tractor 14H206-14H214 769C Truck 1X2877-1X3017, 3019-3022, 3032, 3034-3042 773B Truck 63W1221-63W1347, 1349, 1352, 1353 777 Truck 84A1286-84A1406, 1410-1412, 1414-1439, 1442, 1444 Special Note on Parts Ordering (U.S. and Canada) Automatic shipment of the appropriate parts will be made on behalf of USCD and Canadian dealers. U. S. and Canadian owners will receive the attached Owner Notification. All other dealers should order all necessary parts for this Program. These are: 1 - 8W1053 Neutral Start Group * (For all 700's) 1 - 8W1061 Neutral Start Group ** (For 651E, 657E Tractors) * List only the 8W1053 Group part number on claims. The following 8W1053 Group consists is listed only for your convenience and verification. 1 - 8W980 Harness As. - - 5P3859 Tape 1 - 8W977 Cam 1 - 8W1026 Harness As. 2 - 343223 Screw 1 - 7N9738 Housing 1 - 7T6141 Switch As. 1 - 7N7779 Socket 2 - 2N3477 Screw 1 - 7N7780 Pin 2 - 4B5324 Washer 1 - 9G9150 Clip 2 - 7D6922 Nut 1 - 3T3048 Clip As. 1 - 8W1056 Plate 1 - 8W978 Plate 2 - 310215 Bolt 2 - 309615 Screw 2 - 9S8750 Nut 5 - 3S2093 Strap 2 - 5P537 Washer 1 - 8K1433 Grommet 1 - 8W1025 Harness As. 2 - 309615 Screw ** List only the 8W1061 Group part numbers on claims. The following 8W1061 Group consists is listed for your convenience and verification: 1 - 8W980 Harness As. 2 - 310215 Bolt 1 - 8W977 Cam 2 - 5P537 Washer 2 - 343223 Screw 2 - 9S8750 Nut 1 - 8W982 Plate 1 - 8W981 Harness As. 1 - 7T6141 Switch As. 41 dm (13.5') - 5P3859 Tape 2 - 2N3477 Screw 1 - 8W978 Plate 4 - 4B5324 Washer 2 - 309615 Screw 2 - 7D6922 Nut Action Requested Install the new parts on all the listed machines. Use the attached Procedures. When applicable, do this work at the same time as the modification in December 13, 1984 Service Letter (PI3079) and January 15, 1985 Service Letter, PI3086. PI3079 applies only to certain 776 Tractors and 777 Trucks. Warranty Allowances Caterpillar Dealer User Parts Labor Hr. Parts Labor Hr. Parts Labor Hr. 651E, 657E 100% 3 * 0 0 0 0 700's 100% 3 ** 0 0 0 0 * This is a 3-hr. job. ** This is a 3-hr. job. A one-time allowance for reasonable labor is also allowed if the console template is made. Parts Disposition Dispose of the parts in accordance with your Warranty Bulletin on warranty parts handling. MAKE EVERY EFFORT TO COMPLETE THIS PROGRAM AS SOON AS POSSIBLE Attach. (2) Owner Notification Installation Procedure COPY OF MAIL NOTIFICATION FOR U.S. AND CANADIAN OWNERS XYZ Corporation 3240 Arrow Drive Anywhere, YZ 99999 SAFETY - Possibility of Unexpected Vehicle Movement When Engine Started MODELS INVOLVED - 651E, 657E, 768C, 772B, 776 Tractors; 769C, 773B, 777 Trucks Dear Caterpillar Owner: On the machines listed above, the engine can be started with the transmission in gear. If the operator attempts to start the machine and is unaware that the transmission is in gear, the vehicle can move unexpectedly. Service To Be Performed Caterpillar would like to install new parts on your machine(s) which prevent the engine from starting with the transmission control lever in gear. This will be done at no cost to you. To Have Service Performed Contact your local Caterpillar dealer immediately and schedule a time to have the service performed. The repair time to do this service is about two to three hours, depending on the model. Our records indicate you own the machines listed