31207-ZV5-013 Honda CLUTCH, OVERRUNNING (Honda Code 6672463).


31207-ZV5-013 CLUTCH, OVERRUNNING (Honda Code 6672463). Honda BF40A1 LHA, BF40A1 LHTA, BF40A1 LRA, BF40A1 LRTA, BF40A1 XRTA, BF40A2 LHA, BF40A2 LHTA, BF40A2 LRA, BF40A2 LRTA, BF40A2 XRTA, BF40A3 LHA, BF40A3 LHTA, BF40A3 LRA, BF40A3 LRTA, BF40A3 XRTA, BF40A4 LHA, BF40A4 LHTA, BF40A4 LRTA, BF40A5 LHA, BF40A5 LHTA CLUTCH
31207-ZV5-013 CLUTCH, OVERRUNNING (Honda Code 6672463). Honda
Rating:
13

Buy CLUTCH, OVERRUNNING (Honda Code 6672463). 31207-ZV5-013 Honda genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$182.31
 

30-05-2023
0.25[0.11] Pounds
-: -
Honda 31207-ZV5-013 Clutch Overrunning
Honda 31207-ZV5-013 Clutch Overrunning
Number on catalog scheme: 2
 

Honda entire parts catalog list:

BF40A1 LHA 2001
BF40A1 LHTA 2001
BF40A1 LRA 2001
BF40A1 LRTA 2001
BF40A1 XRTA 2001
BF40A2 LHA 2002
BF40A2 LHTA 2002
BF40A2 LRA 2002
BF40A2 LRTA 2002
BF40A2 XRTA 2002
BF40A3 LHA 2003
BF40A3 LHTA 2003
BF40A3 LRA 2003
BF40A3 LRTA 2003
BF40A3 XRTA 2003
BF40A4 LHA 2004
BF40A4 LHTA 2004
BF40A4 LRTA 2004
BF40A5 LHA 2005
BF40A5 LHTA 2005
BF40A5 LRTA 2005
BF40A6 LHA 2006
BF40A6 LHTA 2006
BF40A6 LRTA 2006
BF40AK0 LHA 2007
BF40AK0 LRTA 2007
BF40DK2 LHA 2007
BF40DK2 LRTA 2007
BF50A1 LHTA 2001
BF50A1 LRA 2001
BF50A1 LRTA 2001
BF50A1 SRJA 2001
BF50A1 XRTA 2001
BF50A2 LHTA 2002
BF50A2 LRA 2002
BF50A2 LRTA 2002
BF50A2 SRJA 2002
BF50A2 XRTA 2002
BF50A3 LHTA 2003
BF50A3 LRA 2003
BF50A3 LRTA 2003
BF50A3 SRJA 2003
BF50A3 XRTA 2003
BF50A4 LHTA 2004
BF50A4 LRTA 2004
BF50A4 SRJA 2004
BF50A4 XRTA 2004
BF50A5 LHTA 2005
BF50A5 LRTA 2005
BF50A5 SRJA 2005
BF50A5 XRTA 2005
BF50A6 LHTA 2006
BF50A6 LRTA 2006
BF50A6 SRJA 2006
BF50A6 XRTA 2006
BF50AK0 LRTA 2007
BF50AK0 SRJA 2007
BF50AK0 XRTA 2007
BF50DK2 LRTA 2007
BF50DK2 XRTA 2007

Information:


Table 1
J1939 Code and Description Comments
101-0
Engine Crankcase Pressure : High - most severe (3) The engine crankcase pressure is greater than the trip point pressure for the programmed delay time.
The code is logged.
101-15
Engine Crankcase Pressure : High - least severe (1) The engine crankcase pressure is greater than the trip point pressure for the programmed delay time.
The code is logged. Probable Causes
Oil level
Crankcase breather
Ventilation system (if equipped)
Sensor
Worn engine componentsRecommended Actions
Table 2
Troubleshooting Test Steps Values Results
1. Check the Engine Oil Level
Oil Level
Result: The engine oil level is OK.
Proceed to Test Step 2.
Result: The engine oil level is high.
Repair: Troubleshoot the cause of the incorrect oil level.
If the problem is not resolved, proceed to Test Step 2.
2. Check for a Plugged Crankcase Breather
Note: If the engine is running in cold ambient temperatures, check to ensure that the breather tube is not plugged with ice.
Plugged Breather
Result: The crankcase breather is not plugged.
Proceed to Test Step 3.
Result: The crankcase breather is plugged.
Repair: Replace the crankcase breather.
Note: A plugged crankcase breather can cause the crankshaft seal to leak. Sealing of the piston rings can be lost and the increase in crankcase blowby will increase the crankcase pressure.
If the problem is not resolved, proceed to Test Step 3.
3. Check the Crankcase Ventilation System
Note: Engines that use bio-gas may have a system for ventilation of the crankcase. A problem with the ventilation system can increase the crankcase pressure.
Ventilation System
Result: The crankcase ventilation system is OK.
Proceed to Test Step 4.
Result: The crankcase ventilation system is NOT OK.
Repair: For information on crankcase ventilation system, refer to the Original Equipment Manufacturers (OEM) service information.
If the problem is not resolved, proceed to Test Step 4.
4. Check the Crankcase Pressure Sensor
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Turn the main disconnect switch to the ON position. Do not start the engine.
C. Remove the oil filler cap.
D. Use Cat ET to monitor the following pressures:
- Crankcase pressure
Sensor
Result: The crankcase pressure is within 0 1 kPa (0 4inch of H2O) of 0 with the main disconnect switch in the ON position.
Proceed to Test Step 6.
Result: The crankcase pressure is not within 0 1 kPa (0 4inch of H2O) of 0 with the main disconnect switch in the ON position.
Proceed to Test Step 5.
5. Inspect the Electrical Connectors and the Wiring
A. Turn the main disconnect switch to the OFF position.
B. Thoroughly inspect the connectors. Refer to Troubleshooting, "Electrical Connectors-Inspect" for additional information.
C. Perform a 45 N (10 lb) pull test on the connector wires.
D. Check the harness for abrasions and pinch points.
Connectors and Wiring
Result: The connectors and wiring appear to be OK.
Repair: Replace the sensor.
If the problem is not resolved, proceed to Test Step 6.
Result: There is a problem with the connectors and/or wiring.
Repair: Repair or replace the connectors or wiring. Ensure that all the seals are properly in place and ensure that the connectors are coupled.
If the problem is not resolved, proceed to Test Step 6.
6. Inspect the Engine for Internal Problems
Note: Damaged pistons or rings can cause too much pressure in the crankcase. This condition will cause the engine to run rough.
Damaged or Worn Engine Components
Result: There are worn or damaged engine components.
Repair: Repair or replace the worn or damaged engine components.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts clutch Honda:

31207-ZV5-003
 
31207-ZV5-003 CLUTCH, OVERRUNNING (Honda Code 3703576).
BF35AM LHA, BF35AM LRA, BF35AM LRTA, BF35AM SHA, BF35AM XRTA, BF40A1 LHA, BF40A1 LHTA, BF40A1 LRA, BF40A1 LRTA, BF40A1 XRTA, BF40AW LHA, BF40AW LHTA, BF40AW LRA, BF40AW LRTA, BF40AW XRTA, BF40AX LHA, BF40AX LHTA, BF40AX LRA, BF40AX LRTA, BF40AX XRTA,
Back to top