91552-ZZ3-000 COLLAR (6MM) Honda
BF60AK1 LRTA, BF60AK1 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
COLLAR
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Compatible models:
Honda entire parts catalog list:
- SHIFT SHAFT » 91552-ZZ3-000
- SHIFT SHAFT » 91552-ZZ3-000
- SHIFT SHAFT » 91552-ZZ3-000
- SHIFT SHAFT » 91552-ZZ3-000
- SHIFT SHAFT » 91552-ZZ3-000
Information:
4. Disconnect heater hose (1) from the housing assembly.5. Remove the hose from the housing assembly on the water pump to the inlet elbow on the radiator.6. Remove bolts (2) that hold the housing assembly in position. Remove housing assembly (3). 7. Remove tube assembly (5).8. Remove four bolts (4). 9. Remove nuts (6) from behind the water pump. Remove water pump (7).Install Water Pump
1. Check the condition of the seal in the housing assembly for the water pump. If the seal has damage, use new parts for replacement. 2. Put water pump (1) in position on the timing gear cover. Install nuts (2) that hold it. 3. Install four bolts (3).4. Install the tube assembly to the water temperature regulator housing on the right side of the machine. 5. Install housing assembly (5) over the water pump. Install the bolts that hold it.6. Install the hose from the water pump to the inlet elbow on the radiator.7. Connect heater hose (4) to th housing assembly.8. Install the vee belt set for the fan.9. Install the panel over the water pump. The location of the panel is on the left side of the machine.10. Fill the cooling system with coolant to the correct level. See MAINTENANCE GUIDE.Disassemble Water Pump
start by: a) remove water pump 1. Remove O-ring seal (1) from adapter (2).2. Remove adapter (2) with a screwdriver. Remove the seal from the edge of adapter (2).3. Remove bolt (3) and washer. 4. Remove impeller (4) from the water pump housing with tooling (A). 5. Remove seal assembly (5). Remove ring and seal (6). 6. Remove the bolt and washer that hold gear (7) on the water pump shaft.7. Remove gear (7) with tooling (B).8. Remove bolts and retainer (9).9. Remove O-ring seal (8). 10. Remove shaft (10) and bearings as a unit.11. Remove bearing (11), spacer (12) and bearing (13) from shaft (10).12. Remove lip type seal from the gear side of the water pump. Remove ring and seal from the impeller side of the water pump.Assemble Water Pump
1. Put clean engine oil on the lip seal (1). Install seal (1) as shown with tooling (A). 2. Install bearing (4), spacer (3) and bearing (5) on shaft (2). Install shaft (2) in the pump housing. 3. Install retainer (7) and O-ring seal (8).4. Install gear (6). Install the washer and bolt that hold gear (6) to shaft (2).
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
5. Put ceramic ring (10) in position in the rubber seal (9). Use hand pressure and the tool (which is with the replacement ring) to install the ceramic ring in the housing. 6. Remove spring (12) from seal assembly (11). Use hand pressure and the tool (which is with the replacement ring) to install the seal (11) assembly. Push seal assembly on the shaft until the seal face makes light contact.7. Install spring (12) on the shaft. 8. Install impeller (14) and the washer and bolt (13) that hold the impeller to the pump shaft. Tighten the bolt to a torque of 28 2 lb.ft. (39 3 N m). Make an air pressure test of the seal at 20 psi (140 kPa). 9. Put clean engine oil on the O-ring seals (15). Install the O-ring seals on adapter (16).10. Install adapter (16) in the pump housing with the notch in alignment with dowel (17).end by:a) install water pump
1. Check the condition of the seal in the housing assembly for the water pump. If the seal has damage, use new parts for replacement. 2. Put water pump (1) in position on the timing gear cover. Install nuts (2) that hold it. 3. Install four bolts (3).4. Install the tube assembly to the water temperature regulator housing on the right side of the machine. 5. Install housing assembly (5) over the water pump. Install the bolts that hold it.6. Install the hose from the water pump to the inlet elbow on the radiator.7. Connect heater hose (4) to th housing assembly.8. Install the vee belt set for the fan.9. Install the panel over the water pump. The location of the panel is on the left side of the machine.10. Fill the cooling system with coolant to the correct level. See MAINTENANCE GUIDE.Disassemble Water Pump
start by: a) remove water pump 1. Remove O-ring seal (1) from adapter (2).2. Remove adapter (2) with a screwdriver. Remove the seal from the edge of adapter (2).3. Remove bolt (3) and washer. 4. Remove impeller (4) from the water pump housing with tooling (A). 5. Remove seal assembly (5). Remove ring and seal (6). 6. Remove the bolt and washer that hold gear (7) on the water pump shaft.7. Remove gear (7) with tooling (B).8. Remove bolts and retainer (9).9. Remove O-ring seal (8). 10. Remove shaft (10) and bearings as a unit.11. Remove bearing (11), spacer (12) and bearing (13) from shaft (10).12. Remove lip type seal from the gear side of the water pump. Remove ring and seal from the impeller side of the water pump.Assemble Water Pump
1. Put clean engine oil on the lip seal (1). Install seal (1) as shown with tooling (A). 2. Install bearing (4), spacer (3) and bearing (5) on shaft (2). Install shaft (2) in the pump housing. 3. Install retainer (7) and O-ring seal (8).4. Install gear (6). Install the washer and bolt that hold gear (6) to shaft (2).
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
5. Put ceramic ring (10) in position in the rubber seal (9). Use hand pressure and the tool (which is with the replacement ring) to install the ceramic ring in the housing. 6. Remove spring (12) from seal assembly (11). Use hand pressure and the tool (which is with the replacement ring) to install the seal (11) assembly. Push seal assembly on the shaft until the seal face makes light contact.7. Install spring (12) on the shaft. 8. Install impeller (14) and the washer and bolt (13) that hold the impeller to the pump shaft. Tighten the bolt to a torque of 28 2 lb.ft. (39 3 N m). Make an air pressure test of the seal at 20 psi (140 kPa). 9. Put clean engine oil on the O-ring seals (15). Install the O-ring seals on adapter (16).10. Install adapter (16) in the pump housing with the notch in alignment with dowel (17).end by:a) install water pump
Parts collar Honda:
91556-ZV5-000
91556-ZV5-000 COLLAR, DISTANCE (10X90) (Honda Code 3706876).
BF35AM LHA, BF35AM LRA, BF35AM LRTA, BF35AM SHA, BF35AM XRTA, BF40A1 LHA, BF40A1 LHTA, BF40A1 LRA, BF40A1 LRTA, BF40A1 XRTA, BF40A2 LHA, BF40A2 LHTA, BF40A2 LRA, BF40A2 LRTA, BF40A2 XRTA, BF40A3 LHA, BF40A3 LHTA, BF40A3 LRA, BF40A3 LRTA, BF40A3 XRTA,
24854-ZV5-000
24854-ZV5-000 COLLAR, SLIDING PLATE (Honda Code 3703196).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
91567-ZV5-000
91567-ZV5-000 COLLAR, LINK JOINT (Honda Code 3706918).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
91570-ZV5-000
91570-ZV5-000 COLLAR, DISTANCE (6X10X43.5) (Honda Code 3706942).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
91560-ZV5-000
91560-ZV5-000 COLLAR, STEERING ROD (Honda Code 3706892).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
91553-ZZ3-000
91553-ZZ3-000 COLLAR, DISTANCE (6.1X9.1X20.5)
BF60AK1 LRTA, BF60AK1 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
91555-ZZ3-000
91555-ZZ3-000 COLLAR, DISTANCE (6.5X16X14.5)
BF60AK1 LRTA, BF60AK1 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
91554-ZZ3-000
91554-ZZ3-000 COLLAR, DISTANCE (6.5X16X16.5)
BF60AK1 LRTA, BF60AK1 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA