91554-ZY9-000 Honda COLLAR, DISTANCE (6.2X7.5)


91554-ZY9-000 COLLAR, DISTANCE (6.2X7.5) Honda BF60AK1 LRTA, BF60AK1 XRTA, BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA COLLAR
91554-ZY9-000 COLLAR, DISTANCE (6.2X7.5) Honda
Rating:
103

Buy COLLAR, DISTANCE (6.2X7.5) 91554-ZY9-000 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 25
 

Honda entire parts catalog list:

BF60AK1 LRTA 2007
BF60AK1 XRTA 2007
BF75DK0 LHTA 2007
BF75DK0 LRTA 2007
BF75DK2 LRTA 2007
BF90DK0 LHTA 2007
BF90DK0 LRTA 2007
BF90DK0 XRTA 2007
BF90DK2 LRTA 2007
BF90DK2 XRTA 2007
BFP60AK1 LRTA 2007
BFP60AK1 LRTB 2007
BFP60AK1 XRTA 2007

Information:

Face Run Out (Axial Eccentricity) Of The Flywheel Housing
8T5096 Dial Indicator Group Installed (Typical Example)If any method other than given here is used, always remember bearing clearance must be removed to get correct measurements.1. Fasten a dial indicator to the flywheel so the anvil of the indicator will touch the face of the flywheel housing.2. Put a force on the crankshaft toward the rear before the indicator is read at each point.
Checking Face Runout Of The Flywheel Housing3. With dial indicator set at "0" (zero) at location (A), turn the flywheel and read the indicator at locations (B), (C) and (D).4. The difference between lower and higher measurements taken at all four points must not be more than 0.38 mm (.015 in), which is the maximum permissible face run out (axial eccentricity) of the flywheel housing.Bore Runout (Radial Eccentricity) Of The Flywheel Housing
1. Fasten the dial indicator as shown so the anvil of the indicator will touch the bore of the flywheel housing.2. With the dial indicator in position at (C), adjust the dial indicator to "0" (zero). Push the crankshaft up against the top of the bearing. Write the measurement for bearing clearance on line 1 in column (C) in the Chart For Dial Indicator Measurements.
8T5096 Dial Indicator Group Installed (Typical Example) Write the dial indicator measurements with their positive (+) and negative (-) notation (signs). This notation is necessary for making the calculations in the chart correctly.3. Divide the measurement from Step 2 by 2. Write this number on line 1 in columns (B) & (D).4. Turn the flywheel to put the dial indicator at (A). Adjust the dial indicator to "0" (zero).5. Turn the flywheel counterclockwise to put the dial indicator at (B). Write the measurements in the chart.
Checking Bore Runout Of The Flywheel Housing6. Turn the flywheel counterclockwise to put the dial indicator at (C). Write the measurement in the chart.7. Turn the flywheel counterclockwise to put the dial indicator at (D). Write the measurement in the chart. 8. Add lines I & II by columns.9. Subtract the smaller number from the larger number in line III in columns (B) & (D). The result is the horizontal eccentricity (out of round). Line III, column (C) is the vertical eccentricity.10. On the graph for total eccentricity, find the point of intersection of the lines for vertical eccentricity and horizontal eccentricity.11. If the point of intersection is in the range marked "Acceptable", the bore is in alignment. If the point of intersection is in the range marked "Not Acceptable", the flywheel housing must be changed.
Graph For Total Eccentricity
(1) Total Vertical Eccentricity [mm (in)]. (2) Total Horizontal Eccentricity [mm (in)]. (3) Acceptable. (4) Not Acceptable.Face Runout (Axial Eccentricity) Of The Flywheel
1. Install the dial indicator as shown. Always put a force on the crankshaft in the same direction before the indicator is read so the crankshaft end clearance (movement) is always removed.
Checking Face Runout Of The Flywheel (Typical Example)2. Set the dial indicator to read "0" (zero).3. Turn the flywheel and read the indicator every 90 degrees.4. The difference between the lower and higher measurements taken at all four points must not be more than 0.15 mm (.006 in), which is the maximum permissible face runout (axial eccentricity) of the flywheel.Bore Runout (Radial Eccentricity) Of The Flywheel
Checking Bore Runout Of The Flywheel (Typical Example)
(1) 7H1945 Holding Rod (2) 7H1645 Holding Rod (3) 7H1942 indicator (4) 7H1940 Universal Attachment1. Install the dial indicator (3) and make an adjustment of the universal attachment (4) so it makes contact as shown.2. Set the dial indicator to read "0" (zero).3. Turn the flywheel and read the indicator every 90 degrees.4. The difference between the lower and higher measurements taken at all four points must not be more than 0.15 mm (.006 in), which is the maximum permissible bore runout (radial eccentricity) of the flywheel.5. Runout (eccentricity) of the bore for the pilot bearing for the flywheel clutch, must not exceed 0.13 mm (.005 in).
Checking Flywheel Clutch Pilot Bearing Bore


Parts collar Honda:

91556-ZV5-000
 
91556-ZV5-000 COLLAR, DISTANCE (10X90) (Honda Code 3706876).
BF35AM LHA, BF35AM LRA, BF35AM LRTA, BF35AM SHA, BF35AM XRTA, BF40A1 LHA, BF40A1 LHTA, BF40A1 LRA, BF40A1 LRTA, BF40A1 XRTA, BF40A2 LHA, BF40A2 LHTA, BF40A2 LRA, BF40A2 LRTA, BF40A2 XRTA, BF40A3 LHA, BF40A3 LHTA, BF40A3 LRA, BF40A3 LRTA, BF40A3 XRTA,
24854-ZV5-000
COLLAR, SLIDING PLATE (Honda Code 3703196).
24854-ZV5-000 COLLAR, SLIDING PLATE (Honda Code 3703196).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
91567-ZV5-000
 
91567-ZV5-000 COLLAR, LINK JOINT (Honda Code 3706918).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
91570-ZV5-000
COLLAR, DISTANCE (6X10X43.5) (Honda Code 3706942).
91570-ZV5-000 COLLAR, DISTANCE (6X10X43.5) (Honda Code 3706942).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
91560-ZV5-000
COLLAR, STEERING ROD (Honda Code 3706892).
91560-ZV5-000 COLLAR, STEERING ROD (Honda Code 3706892).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
91553-ZZ3-000
COLLAR, DISTANCE (6.1X9.1X20.5)
91553-ZZ3-000 COLLAR, DISTANCE (6.1X9.1X20.5)
BF60AK1 LRTA, BF60AK1 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
91555-ZZ3-000
COLLAR, DISTANCE (6.5X16X14.5)
91555-ZZ3-000 COLLAR, DISTANCE (6.5X16X14.5)
BF60AK1 LRTA, BF60AK1 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
91552-ZZ3-000
COLLAR (6MM)
91552-ZZ3-000 COLLAR (6MM)
BF60AK1 LRTA, BF60AK1 XRTA, BFP60AK1 LRTA, BFP60AK1 LRTB, BFP60AK1 XRTA
Back to top