19277-ZY9-000 Honda COVER, FLUSH VALVE


19277-ZY9-000 COVER, FLUSH VALVE Honda BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA COVER
19277-ZY9-000 COVER, FLUSH VALVE Honda
Rating:
58

Buy COVER, FLUSH VALVE 19277-ZY9-000 Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Honda entire parts catalog list:

BF75DK0 LHTA 2007
BF75DK0 LRTA 2007
BF75DK2 LRTA 2007
BF90DK0 LHTA 2007
BF90DK0 LRTA 2007
BF90DK0 XRTA 2007
BF90DK2 LRTA 2007
BF90DK2 XRTA 2007

Information:

For removal of the governor from the fuel injection pump housing, see Disassemble Governor. 1. Remove cover (1). 2. Install tooling (B). Engage the timing pin in the center groove of the fuel rack. Move the fuel rack in the direction of the arrow to find the center groove.3. Install tooling (D), and remove bushing (2). 4. Install tooling (E), and remove the fuel injection pump. 5. Remove spacer (3). Do not mix components from fuel injection pump assemblies.6. Remove the remainder of the fuel injection pumps and spacers with Steps 2 through 5 done again for each injection pump. 7. Remove cover (4). 8. Remove fuel rack (5). 9. Use a bar magnet to remove lifter assemblies (6). Put identification marks on the lifter assemblies as to their location in the fuel injection pump housing. 10. Use tooling (A) to remove snap ring (7). Do not let the camshaft fall because the machined surfaces will be scratched.11. Use a plastic hammer to make camshaft (8) move out of washer (9). 12. Remove camshaft (8). 13. Use tooling (C) to remove rack rear bearing (10) and camshaft rear bearing (11). 14. Install the location plate from tooling (B). Align the bore in the plate with the O-ring seal counterbore in the fuel injection pump housing. Make a mark for alignment.15. Remove tooling (B). 16. Use tooling (C) to remove rack bearing (12) and camshaft bearing (13).Assemble Fuel Injection Pump Housing
Be sure all of oil passages are clear, and put clean engine oil on all parts before assembly. 1. Use tool (A) to install the camshaft bearing in the drive end of the fuel injection pump housing with the joint of the bearing toward the top of the fuel injection pump housing. Install the bearing so it is 1.00 0.25 mm (.039 .010 in) below the surface of the housing. 2. Use tooling (A) to install the camshaft bearing in the governor end of the fuel injection pump housing with the joint of the bearing toward the top of the fuel injection pump housing. Install the bearing so it is 0.25 0.20 mm (.010 0.008 in) below the surface of the housing.3. Use tooling (A) to install the fuel rack rear (governor end) bearing. Install the bearing so it is 7.16 0.13 mm (.282 .005 in) below the surface of the housing. 4. Install the plate assembly from tooling (B) on the drive end of the fuel injection pump housing to install the bearing for the fuel rack. Use clean grease to hold the new fuel rack bearing on the driver from tooling (B). Install the driver and bearing in the plate assembly with the groove in the driver in alignment with the pin in the plate assembly, and use a hammer to push the bearing into position. The bearing will be installed to the correct depth when the shoulder of the driver is against the plate assembly.5. Remove tooling (B) from the fuel injection pump housing. The rack bearing must be installed so it is 0.25 0.25 mm (0.010 0.010 in) below the surface of the housing. 6. Install fuel injection pump camshaft (8) in the fuel injection pump housing.7. Put the fuel injection pump housing on end, and put a block under the camshaft. 8. Put washer (9) over the end of the camshaft, and use tooling (A) and (C) to push washer (9) against its seat on the camshaft. The camshaft must have 0.285 0.235 mm (0.0112 0.0093 in) end play when the washer is pushed against cam shoulder. 9. Use tool (D) to install snap ring (7) in the groove in the camshaft.
If the original lifters are to be installed, be sure to install them in their respective bores in the pump housing. New lifters can be mixed.
10. Install four lifter assemblies (6) in the fuel injection pump housing with the groove in the lifter in alignment with the pin in the housing. 11. Install fuel rack (5) in the fuel injection pump housing. Install the rack with the groove in the end of fuel rack in alignment with the ear (tab) of the rack bearing at the drive end of the fuel injection pump housing. 12. Install the timing pin from tooling (B). Engage the timing pin in the center groove of the fuel rack. Move the fuel rack in the direction of the arrow to locate the center groove.13. Install spacer (3). 14. Put (slot) groove (15) in the gear segment 180° away from groove (14) in the barrel. When the fuel injection pump is installed, groove (14) must engage the dowel (16). 15. Use tool (E) to install the fuel injection pump. Installation is made easier by rotation of the cam lobe away from the lifter assembly. 16. Install O-ring seal (17). 17. Install bushing (2). Tighten bushing (2) by hand until the bushing is even with the top of the housing. If installation of the bushing cannot be made this far by hand, remove it. Remove the pump, put the parts in alignment again, and install the bushing again.18. Use tool (F) and a torque wrench to tighten the bushing to a torque of 163 14 N m (120 10 lb ft).19. Remove tooling (B). 20. Install tooling (G) and (H) to measure total rack travel. Correct rack travel is 15.70 mm (.618 in). A smaller measurement is an indication of incorrect fuel injection pump installation.21. Complete the installation of the remainder of fuel injection pumps as given in Steps 11-19. 22. Install cover (1) and gasket.23. Install the governor on the fuel injection pump housing. See Assemble Governor; then install the fuel injection pump housing and governor on the engine.


Parts cover Honda:

24812-ZW7-U01
COVER, GRIP (Honda Code 6799548).
24812-ZW7-U01 COVER, GRIP (Honda Code 6799548).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
24814-ZW7-U01
COVER, LOCK ARM (Honda Code 6799597).
24814-ZW7-U01 COVER, LOCK ARM (Honda Code 6799597).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
24812-ZW5-U01
COVER, L. GRIP (Honda Code 6799522).
24812-ZW5-U01 COVER, L. GRIP (Honda Code 6799522).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
24813-ZW5-U21
COVER, DUAL GRIP (Honda Code 6799563).
24813-ZW5-U21 COVER, DUAL GRIP (Honda Code 6799563).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
24812-ZW5-U11
COVER, R. GRIP (Honda Code 6799530).
24812-ZW5-U11 COVER, R. GRIP (Honda Code 6799530).
BF115A1 LA, BF115A1 LCA, BF115A1 XA, BF115A1 XCA, BF115A2 LA, BF115A2 LCA, BF115A2 XA, BF115A2 XCA, BF115A3 LA, BF115A3 LCA, BF115A3 XA, BF115A3 XCA, BF115A4 LA, BF115A4 LCA, BF115A4 XA, BF115A4 XCA, BF115A5 LA, BF115A5 LCA, BF115A5 XA, BF115A5 XCA,
19315-ZY9-000
COVER, THERMOSTAT (Honda Code 9139536).
19315-ZY9-000 COVER, THERMOSTAT (Honda Code 9139536).
BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA
19361-ZY9-010
COVER, WATER JACKET
19361-ZY9-010 COVER, WATER JACKET
BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA
38216-ZY9-003
COVER ASSY., FUSE (70A) (Honda Code 8577033).
38216-ZY9-003 COVER ASSY., FUSE (70A) (Honda Code 8577033).
BF75DK0 LHTA, BF75DK0 LRTA, BF75DK2 LRTA, BF90DK0 LHTA, BF90DK0 LRTA, BF90DK0 XRTA, BF90DK2 LRTA, BF90DK2 XRTA
Back to top