80105-MG9-000 Honda CUSHION, AIR CLEANER (Honda Code 1530062).


80105-MG9-000 CUSHION, AIR CLEANER (Honda Code 1530062). Honda BF2.3DK2 LCHA, BF2.3DK2 SCHA, BF2D1 LCHA, BF2D1 SA, BF2D1 SAB, BF2D1 SCAB, BF2D1 SCHA, BF2D1 SHA, BF2D2 LCHA, BF2D2 SA, BF2D2 SAB, BF2D2 SCAB, BF2D2 SCHA, BF2D2 SHA, BF2D3 LCHA, BF2D3 SA, BF2D3 SAB, BF2D3 SCAB, BF2D3 SCHA, BF2D3 SHA, BF2D4 LCHA, BF2D CUSHION
80105-MG9-000 CUSHION, AIR CLEANER (Honda Code 1530062). Honda
Rating:
103

Buy CUSHION, AIR CLEANER (Honda Code 1530062). 80105-MG9-000 Honda genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$11.59
 

20-06-2024
0.25[0.11] pounds
US: PowerToolReplacement
Honda 80105-MG9-000 Cushion Air Cleaner
Honda Honda 80105-MG9-000 Cushion Air Cleaner
Number on catalog scheme: 13
 

Honda entire parts catalog list:

BF2.3DK2 LCHA 2007
BF2.3DK2 SCHA 2007
BF2D1 LCHA 2001
BF2D1 SA 2001
BF2D1 SAB 2001
BF2D1 SCAB 2001
BF2D1 SCHA 2001
BF2D1 SHA 2001
BF2D2 LCHA 2002
BF2D2 SA 2002
BF2D2 SAB 2002
BF2D2 SCAB 2002
BF2D2 SCHA 2002
BF2D2 SHA 2002
BF2D3 LCHA 2003
BF2D3 SA 2003
BF2D3 SAB 2003
BF2D3 SCAB 2003
BF2D3 SCHA 2003
BF2D3 SHA 2003
BF2D4 LCHA 2004
BF2D4 SA 2004
BF2D4 SCHA 2004
BF2D4 SHA 2004
BF2D5 LCHA 2005
BF2D5 SCHA 2005
BF2D5 SHA 2005
BF2D6 LCHA 2006
BF2D6 SCHA 2006
BF2D6 SHA 2006
BF2DK0 LCHA 2007
BF2DK0 SCHA 2007
BF2DX LCHA 1999
BF2DX SA 1999
BF2DX SAB 1999
BF2DX SCAB 1999
BF2DX SCHA 1999
BF2DY LCHA 2000
BF2DY SA 2000
BF2DY SAB 2000
BF2DY SCAB 2000
BF2DY SCHA 2000
BF2DY SHA 2000

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
5576-14
Aftertreatment #1 Identification : Special Instruction 3468-14
Aftertreatment #1 Identification Number Module : Special Instruction The code is logged.
5577-14
Aftertreatment #2 Identification : Special Instruction 3469-14
Aftertreatment #2 Identification : Special Instruction The code is logged.
6806-14
ECU Interface Mismatch : Special Instruction E1132 (2)
Inconsistent Configuration Detected The code is logged.
7105-14
Aftertreatment #1 Inconsistent Configuration Detected : Special Instruction E1585 (2)
Aftertreatment #1 Inconsistent Configuration Detected The code is logged.
N/A 3050-14
Drivetrain Control : Special Instruction The engine Electronic Control Module (ECM) is not receiving speed command from the drivetrain control ECM.
Table 2
Associated Codes
J1939 Code CDL Code Troubleshooting Procedure
639-9 247-9 Troubleshooting, "Data Link - Test"
639-14 247-14 Troubleshooting, "Data Link - Test"
1231-9 2348-9 Troubleshooting, "Data Link - Test"
1231-14 2348-14 Troubleshooting, "Data Link - Test"
1235-9 5856-9 Troubleshooting, "Data Link - Test"
1235-14 5856-14 Troubleshooting, "Data Link - Test"
Table 3
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: An associated -9 or -14 code is active or logged.
Repair: Repair all associated -9 or -14 codes before continuing with this procedure. Refer to Troubleshooting, "Data Link - Test" for additional information.
Result: A 5576-14, 5577-14, 3468-14, or 3469-14 code is active or logged.
Proceed to Test Step 2.
Result: An E1132 (2) or 6806-14 code is active or logged.
Proceed to Test Step 3.
Result: An E1585 (2) or 7105-14 code is active or logged.
Proceed to Test Step 4.
2. Check for Incorrect Configuration Parameters
A. Connect Cat ET.
B. Use Cat ET to verify that the correct parameter is being used.
- "Factory Installed Aftertreatment Identification Number"
C. Connect to the "SCR Controller". Under "Aftertreatment Configuration" in the Configuration Parameters, make sure that the "Factory Installed Aftertreatment Identification Number" matches the Clean Emissions Module (CEM) serial number on the CEM data plate.
Identification Number
Result: The CEM serial number matches the "Factory Installed Aftertreatment Identification Number".
Repair: Replace the aftertreatment identification module.
If the problem is not resolved, proceed to Test Step 3.
Result: The CEM serial number does not match the "Factory Installed Aftertreatment Identification Number".
Repair: Verify that the correct CEM is installed on the engine. Program the CEM serial number into the "Factory Installed Aftertreatment Identification Number".
If the problem is not resolved, proceed to Test Step 3.
3. Ensure that the latest Flash File Software is Installed in the Selective Catalyst Reduction (SCR) System
A. Connect Cat ET.
B. Use Cat ET to update the following software:
- "SCR Controller"
Note: The 6806 -14 or E1132 (2) code indicates that the software in the Engine ECM and the"SCR Controller" does not match. If the software in one ECM was updated, and the other was not, this code will log.
Flash File
Result: The software updated successfully and the code changed to logged.
Return to service.
4. Ensure that the latest Flash File Software is Installed in the Diesel Exhaust Fluid Control Unit (DCU)
A. Connect Cat ET.
B. Use Cat ET to update the following software:
- "SCR Controller"
- "Diesel Exhaust Fluid Controller #1"
- "Diesel Exhaust Fluid Controller #2"
Note: The 7105-14 or E1585 (2) code indicates the software in the DCUs do not match with the software the SCR Controller is expecting.
Flash File
Result: The software updated successfully and the code changed to logged.
Return to service.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Back to top