12215-ZW2-000ZA Honda CYLINDER HEAD ASSY. *NH8* (Honda Code 6375547). (DARK GRAY)


12215-ZW2-000ZA CYLINDER HEAD ASSY. *NH8* (Honda Code 6375547). (DARK GRAY) Honda BF30A1 LHA, BF30A1 LHSA, BF30A1 LRSA, BF30A1 SHA, BF30A1 SRSA, BF30A2 LHA, BF30A2 LHSA, BF30A2 LRSA, BF30A2 SHA, BF30A2 SRSA, BF30A3 LHA, BF30A3 LHSA, BF30A3 LRSA, BF30A3 SHA, BF30A3 SRSA, BF30AW LHA, BF30AW LHSA, BF30AW LRSA, BF30AW SHA, BF30AW SRSA CYLINDER
12215-ZW2-000ZA CYLINDER HEAD ASSY. *NH8* (Honda Code 6375547). (DARK GRAY) Honda
Rating:
8

Buy CYLINDER HEAD ASSY. *NH8* (Honda Code 6375547). (DARK GRAY) 12215-ZW2-000ZA Honda genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Honda entire parts catalog list:

BF30A1 LHA 2001
BF30A1 LHSA 2001
BF30A1 LRSA 2001
BF30A1 SHA 2001
BF30A1 SRSA 2001
BF30A2 LHA 2002
BF30A2 LHSA 2002
BF30A2 LRSA 2002
BF30A2 SHA 2002
BF30A2 SRSA 2002
BF30A3 LHA 2003
BF30A3 LHSA 2003
BF30A3 LRSA 2003
BF30A3 SHA 2003
BF30A3 SRSA 2003
BF30AW LHA 1998
BF30AW LHSA 1998
BF30AW LRSA 1998
BF30AW SHA 1998
BF30AW SRSA 1998
BF30AX LHA 1999
BF30AX LHSA 1999
BF30AX LRSA 1999
BF30AX SHA 1999
BF30AX SRSA 1999
BF30AY LHA 2000
BF30AY LHSA 2000
BF30AY LRSA 2000
BF30AY SHA 2000
BF30AY SRSA 2000

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
5576-2
Aftertreatment #1 Identification : Erratic, Intermittent, or Incorrect 3468-2
Aftertreatment #1 Identification Number Module : Erratic, Intermittent, or Incorrect The installed Clean Emissions Module (CEM) #1 is not a certified match with the engine.
The code is a confirmed emissions regulation violation. A financial penalty and/or legal action may result, if the problem is not corrected immediately. Do not operate the engine with the active fault.
Engine power is derated.
5576-8
Aftertreatment #1 Identification : Abnormal Frequency, Pulse Width, or Period 3468-8
Aftertreatment #1 Identification Number Module : Abnormal Frequency, Pulse Width, or Period Emissions do not conform to regulations. Do not continue to operate the engine with the active fault.
Engine power is derated.
5577-2
Aftertreatment #2 Identification : Erratic, Intermittent, or Incorrect 3469-2
Aftertreatment #2 Identification Number Module : Erratic, Intermittent, or Incorrect The installed CEM #2 is not a certified match with the engine.
The code is a confirmed emissions regulation violation. A financial penalty and/or legal action may result, if the problem is not corrected immediately. Do not operate the engine with the active fault.
Engine power is derated.
5577-8
Aftertreatment #2 Identification : Abnormal Frequency, Pulse Width, or Period 3469-8
Aftertreatment #2 Identification Number Module : Abnormal Frequency, Pulse Width, or Period Emissions do not conform to regulations. Do not continue to operate the engine with the active fault.
Engine power is derated.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A code is active or logged.
Proceed to Test Step 2.
Illustration 1 g02896037
Typical Clean Emissions Module (CEM) identification plate
Table 3
Troubleshooting Test Steps Values Results
2. Manually Enter the Aftertreatment Identification Information
The Clean Emissions Module (CEM) identification plate is on the electronics panel.
Factory Passwords are required for this procedure.
A. Confirm that a certified CEM is installed on the engine.
Contact your local Cat dealer for a list of approved CEM configurations for your engine.
B. Record the affected CEM serial number and the configuration group from the CEM Identification Plate.
C. Verify that the affected CEM is a certified match with the engine.
Certified Match
Result: The affected CEM is a certified match with the engine.
Proceed to Test Step 3.
Result: The affected CEM is not a certified match for the engine.
Repair: Remove the affected CEM and replace the affected CEM with a certified match for the engine. Refer to Disassembly and Assembly for additional information. When the new CEM is installed, the"Aftertreatment Identification Number Module" will begin communicating with the ECM and the code will be cleared.
When determining if a CEM is a certified match:
The engine ECM will only communicate with the CEM if the total lifetime hours of the engine are less than 100. If the hours are greater than 100, the information from the CEM identification plate must be programmed into the ECM by using Cat ET.
If the problem is not resolved, proceed to Test Step 3.
Illustration 2 g03733735
Typical "Aftertreatment Configuration"
Table 4
Troubleshooting Test Steps Values Results
3. Program the Aftertreatment Identification Number
A. Connect Cat ET.
B. Navigate to the "Aftertreatment Configuration" in the affected "Engine Aftertreatment Controller" page.
C. Program the required "Factory Installed Aftertreatment Identification Number" with the serial number from the CEM Identification Plate.
Identification Number
Result: The code is automatically cleared.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts cylinder Honda:

12210-ZV7-010ZA
 
12210-ZV7-010ZA CYLINDER HEAD *NH8* (DARK GRAY) (Honda Code 6387823).
BF25A1 LHA, BF25A1 LHSA, BF25A1 LRSA, BF25A1 SHA, BF25A1 SHSA, BF25A1 SRSA, BF25A1 XRSA, BF25A2 LHA, BF25A2 LHSA, BF25A2 LRSA, BF25A2 SHA, BF25A2 SHSA, BF25A2 SRSA, BF25A2 XRSA, BF25A3 LHA, BF25A3 LHSA, BF25A3 LRSA, BF25A3 SHA, BF25A3 SHSA, BF25A3 SR
Back to top